16790-5LA-A01
KEIHIN 16790-5LA-A01 ТНВД Honda CR-V Civic Accord 1.5T Earth Dreams L15B7
HM10035, GDP301--200 barПрименяемость к авто и двигателям
| Автомобиль | Двигатель | Годы выпуска |
|---|---|---|
| Honda Civic X 1.5 Turbo | Honda 1.5L Earth Dreams VTEC Turbo & i-VTEC (L15B7 / L15BA / L15BE / L15B2) | 2016-2021 |
| Honda CR-V V 1.5 Turbo | Honda 1.5L Earth Dreams VTEC Turbo & i-VTEC (L15B7 / L15BA / L15BE / L15B2) | 2017-2022 |
| Honda Accord X 1.5 Turbo | Honda 1.5L Earth Dreams VTEC Turbo & i-VTEC (L15B7 / L15BA / L15BE / L15B2) | 2018-2022 |
Технические характеристики
| Параметр | Значение |
|---|---|
| Part Number / SKU | 16790-5LA-A01 |
| Manufacturer Brand | KEIHIN |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Honda 1.5L Earth Dreams Turbo DOHC 16V (L15B7 / L15BA / L15BD) |
| Рабочее давлениеОсн. параметр | |
| Mounting Torque (Flange / Bracket) | 12 N-m (106 lb-in) |
| Fuel Line / Rail Torque | 27 N-m (20 lb-ft) |
| Типичные коды ошибок OBD | P0087, P0172, P0088, P219D |
Совместимый ТНВД (Топливный контур в сборе)
Работает в одном контуре Common Rail высокого давления. При падении давления (P0087) проверьте подачу насоса перед заменой форсунок.
Рекомендации по установке
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 12 N-m (106 lb-in), and torque fuel line fittings to 27 N-m (20 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
Коды неисправностей (DTC) и протоколы диагностики
Основные диагностические коды неисправностей (DTC), возникающие при износе, замыкании цепи или отклонении калибровки данной форсунки Common Rail:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Технические протоколы диагностики и обслуживания
Проверенные сервисные процедуры, пороговые значения тестов и регламенты для данного узла.