06M906036P
BOSCH 06M906036P Inyector Alta Presión Audi S4 S5 RS4 Porsche 2.9T 3.0T EA839
06M906036AE, 0261500478, 0261500479Laser-Drilled Micro-Orifice Solenoid Valve-250 barEspecificaciones técnicas
| Especificación | Valor |
|---|---|
| Tipo de sistema | Bosch HDEV6 Multi-Hole Solenoid Direct Gasoline Fuel Injector |
| Presión de servicioDato clave | |
| Spray Pattern | Precision laser-drilled multi-orifice targeting combustion bowl |
| Fuel Rail Bolt Torque | 10 N·m (flanged retaining bolt) |
| High Pressure Pipe Torque | 25 N·m Flare Nut Connection |
| Coil Resistance | 1.3 - 1.6 Ω at 20°C (High-speed Peak & Hold excitation) |
| Códigos de avería frecuentes | P0300 (Random Misfire), P0301-P0306 (Cylinder Misfire), P0172 / P0175 (System Rich) |
| Workshop Precaution | Combustion chamber Teflon sealing ring must be calibrated with sizing tool before cylinder head insertion |
Bomba de alta presión compatible (Ensamblaje del circuito de combustible)
Funciona en el mismo circuito de alta presión Common Rail. Al diagnosticar baja presión (P0087), verifique el caudal de la bomba antes de sustituir los inyectores.
Consejos de instalación
- [
- {
- "step": 1,
- "title": "Depressurize High Pressure Fuel Circuit",
- "instruction": "Disconnect low pressure electric fuel pump controller or pull fuse. Run engine until it stalls to vent high pressure fuel rail."
- },
- {
- "step": 2,
- "title": "Remove Charge Air Ducting & Fuel Rail Retainers",
- "instruction": "Unbolt hot-V intake charge pipe components. Disconnect electrical harnesses and remove fuel rail retaining bolts (10 N·m)."
- },
- {
- "step": 3,
- "title": "Extract Injectors & Renew Teflon Chamber Seals",
- "instruction": "Use puller tool T10133 to extract injectors from cylinder head. Fit new Teflon combustion seal and backing washer with assembly cone."
- },
- {
- "step": 4,
- "title": "Reinstall Rail & Torque Connections to Spec",
- "instruction": "Seat injectors into head. Torque rail bolts evenly to 10 N·m. Tighten high pressure lines to 25 N·m. Cycle ignition and verify zero fuel weepage."
- }
- ]
Codigos de Falla (DTC) y Protocolos de Diagnostico
Codigos de falla de diagnostico (DTC) comunes que se activan cuando este inyector common rail experimenta desgaste, fallas de circuito o desbalance:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Protocolos Técnicos de Diagnóstico y Servicio
Procedimientos de taller verificados, umbrales de prueba y pautas de servicio para este conjunto.