BOSCH
A2640900200
Ver especificaciones
SolenoidGasoline Direct Injection (GDI)Euro 56
BOSCH A2640900200 Bomba Alta Presión Mercedes C260 C300 E300 2.0T M264 M254
Plataforma de motor:Mercedes-Benz 1.5L & 2.0L Turbocharged DOHC 16V M264 / M254 EQ Boost →
REFERENCIA OE
2640900200, A2640900100, 2640900100, HPP0038, HM10046VÁLVULA DE CONTROL
-TOBERA
-PRESIÓN DE RAIL
200 barNORMA EMISIONESEuro 5 / Euro 6
GARANTÍA12 Meses
02
Aplicaciones de vehículos y motores
| Vehículo | Motor | Años |
|---|---|---|
| Mercedes-Benz C260 / C300 (W205 / W206) & E300 / E350 (W213) | 1.5L & 2.0L Turbo EQ Boost 48V (M264 / M254) | 2018-2024 |
| Mercedes-Benz GLC 300 (X253 / X254) / GLE 350 (V167) / CLS 350 | 2.0L Turbocharged DOHC 16V (M264.920 / M254.920) | 2019-2024 |
03
Especificaciones técnicas
| Especificación | Valor |
|---|---|
| Part Number / SKU | A2640900200 |
| Manufacturer Brand | BOSCH |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Mercedes-Benz 1.5L & 2.0L Turbocharged DOHC 16V M264 / M254 EQ Boost |
| Presión de servicioDato clave | |
| Mounting Torque (Flange / Bracket) | 20 N-m (15 lb-ft) |
| Fuel Line / Rail Torque | 27 N-m (20 lb-ft) |
| Códigos de avería frecuentes | P0087, P0088, P053F, P0171 |
04
Consejos de instalación
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 20 N-m (15 lb-ft), and torque fuel line fittings to 27 N-m (20 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
05
Codigos de Falla (DTC) y Protocolos de Diagnostico
Codigos de falla de diagnostico (DTC) comunes que se activan cuando este inyector common rail experimenta desgaste, fallas de circuito o desbalance:
P0087Critical
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
P0201 - P0208High
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
P0300 / P0301+High
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
P0088High
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
PROTOCOLOS DE TALLER
Protocolos Técnicos de Diagnóstico y Servicio
Procedimientos de taller verificados, umbrales de prueba y pautas de servicio para este conjunto.
DIAGNÓSTICO COMMON RAIL EN TALLER
Leer protocolo técnicoDiagnóstico Bomba Alta Presión: Código P0087 y Bosch CP4
DIAGNÓSTICO TÉCNICO COMMON RAIL
Leer protocolo técnicoDiagnóstico Válvula Dosificadora IMV SCV y Test P0088
PROTOCOLO DE DIAGNÓSTICO OBD-II
Leer protocolo técnicoGuía de diagnóstico de baja presión en el raíl DTC P0087
DIAGNÓSTICO TÉCNICO COMMON RAIL
Leer protocolo técnico