OBD-II DIESEL WERKPLAATSPROTOCOL8-10 min read
P20EEDPF & EmissiesHoge Ernst💡 Motorstoringslampje brandt⚠️ Noodloop actief

P20EE: P20EE SCR NOx-katalysatorrendement onder drempelwaarde (Cilinderrij 1)

Foutcode (DTC) P20EE geeft aan dat de motorregeleenheid (ECM/PCM) heeft gedetecteerd dat het conversierendement van de selectieve katalytische reductie (SCR) NOx-katalysator (Bank 1) onder de gekalibreerde emissiegrenswaarden is gedaald. Moderne Euro 6- en EPA Tier 3-dieselvoertuigen maken gebruik van een SCR-katalysator die stroomopwaarts wordt gevoed door een AdBlue/DEF-doseerklep. Een stroomopwaartse slimme NOx-sensor meet de ongereinigde uitstoot direct na de motor, terwijl een stroomafwaartse NOx-sensor de restuitstoot bij de uitlaat meet. De ECM berekent continu het actuele rendement. Zakt het NOx-reductierendement tijdens een gestandaardiseerde testcyclus onder de 70% (nominale streefwaarde > 90%-95%), dan wordt DTC P20EE opgeslagen en treedt een aftelprocedure voor herstartblokkade in werking.

🚗 BESTUURDERSGIDS & REPARATIEPROTOCOL

🚗 Rijveiligheid, geschatte reparatiekosten & verificatie

🟢 Info: Veilig te rijden / Emissiecontrole
  1. 01

    🚦 Rijveiligheid en mechanisch risico

    Directe inspectie en noodzaak voor een takelwagen

    SCR NOx-katalysatorrendement onder drempelwaarde - Risico op herstartblokkade

    De SCR-emissiekatalysator neutraliseert stikstofoxiden (NOx) onvoldoende. De auto rijdt technisch gezien volkomen normaal, maar de emissiewetgeving voor moderne diesels dwingt een herstartblokkade af ('Geen motorstart mogelijk over 800/300 km' op het dashboard). Zodra deze aftelteller nul bereikt, weigert de motor te starten.

    MECHANISCHE RISICO'S BIJ DOORRIJDEN:Onherroepelijke startblokkade waardoor u strandt langs de weg, kristallisatie van ureumresidu dat het uitlaatsysteem verstopt, en directe afkeur bij de APK-emissietest.
  2. 02

    💰 Typisch werkplaatsbudget

    Verwachte kostenstaffels voor onderdelen en arbeid
    Klein onderhoud / Filter€ 40 - € 120: AdBlue/DEF-tank leegpompen en vullen met verse vloeistof conform ISO 22241, of reinigen van ureumkristallen op de AdBlue-doseerklep.

    Sensorreiniging, brandstoffilter vervangen, zekering controleren of contacten reinigen.

    Klep / Sensor vervangen€ 280 - € 550: Vervanging van de stroomopwaartse of stroomafwaartse NOx-sensor (slimme sensor van Continental / Bosch).

    Vervanging enkel onderdeel (drukregelventiel, doseereenheid of gereviseerde verstuiver).

    Grote revisie / Pomp en injectoren€ 1.400 - € 3.200+: Volledige vervanging van het SCR-katalysatorelement of de complete AdBlue-tankinheid inclusief opvoerpomp.

    Revisie hogedrukpomp, nieuwe OEM-verstuivers of vervanging DPF-roetfilter.

    Werkplaatsreferentietarieven. Meer dan 70% van de gevallen wordt opgelost binnen niveau 1 of 2 zonder vervanging van complete subeenheden.

  3. 03

    🧰 Snelle visuele controle zonder gereedschap

    5-minuten garagecheck voordat u de werkplaats belt
    1Inspecteer de AdBlue/DEF-doseerklep: Deze bevindt zich in de voorpijp van het uitlaatsysteem. Draai de klem los en controleer of de sproeikop bedekt is met een witte, bloemkoolachtige korst van gekristalliseerd ureum.
    2Controleer de houdbaarheid en kwaliteit van de AdBlue: Als het voertuig langer dan 6 maanden heeft stilgestaan of als er inferieure vloeistof is gebruikt, ontleedt het ureum in ammoniak en water, wat direct P20EE veroorzaakt.
    3Inspecteer de bedrading van de NOx-sensoren: Kijk onder de auto langs de uitlaattunnel of de gevlochten kabelboom of stuurmodule van de NOx-sensor niet beschadigd is door opspattend steenslag of loshangt.
  4. 04

    🛡️ Bescherming tegen verkeerde diagnoses

    Gerichte vragen aan de monteur om onnodige vervanging te voorkomen
    "Vraag: 'Wilt u eerst de sproeikop van de AdBlue-doseerklep demonteren en reinigen in warm gedestilleerd water voordat u overgaat tot het vervangen van dure NOx-sensoren?'"
    "Vraag: 'Kunt u de live data controleren: wat zijn de exacte ppm-waarden van de stroomopwaartse versus de stroomafwaartse NOx-sensor tijdens een snelwegcyclus van 20 minuten?'"

    Technische opmerking: Stel deze gerichte vragen aan uw monteur voordat u akkoord gaat met dure reparaties:

🔧 PROFESSIONEEL TECHNICUSADVIES & REPARATIEPROTOCOLRAPID ASSESSMENT

30-seconden werkplaatstriage

Belangrijkste symptomen
  • Check Engine Light (MIL) and DEF / AdBlue warning symbols illuminated on the dashboard
  • Instrument cluster displaying an urgent message: 'Engine Restart Prevented in XXX km / miles'
  • No noticeable change in engine power, drivability, or fuel economy (engine runs cleanly, but emissions exceed limits)
Meest waarschijnlijke oorzaken
  • Contaminated, diluted, or expired Diesel Exhaust Fluid (DEF/AdBlue) with urea concentration below 32.5%
  • Heavy white rock-like urea crystallization (biuret deposits) clogging the dosing injector tip or exhaust decomposition pipe
  • Defective, drifting, or poisoned downstream (post-SCR) smart NOx sensor over-reporting residual NOx ppm
Eerste vereiste actie

Connect scan tool live telemetry: compare Target Fuel Rail Pressure vs Actual Rail Pressure and log metering valve command PWM duty cycle during idle and road load.

Expensive Diagnostic Pitfall & Technical Reality

❌ Veelvoorkomende werkplaatsmisvatting:

P20EE confirms that the SCR exhaust catalyst block is poisoned or dead, requiring replacement of the complete underbody SCR catalytic converter canister ($2,800 - $4,500).

🔍 Technische en hydraulische werkelijkheid:

Modern SCR catalyst substrates are engineered to last the full lifecycle of the vehicle (>500,000 km). In over 85% of verified P20EE faults, the SCR catalyst matrix itself is in pristine condition. The efficiency code is triggered because the upstream Diesel Exhaust Fluid (DEF / AdBlue) dosing injector is crusted shut with white urea crystals, the DEF fluid in the tank is adulterated or diluted below the mandatory 32.5% concentration, or the downstream NOx sensor has suffered internal ceramic sensing chamber soot contamination, falsely reporting high tailpipe NOx.

💡 Technisch verificatieprotocol:

Replacing the entire $3,200 SCR catalytic converter vs ultrasonic cleaning of the AdBlue dosing valve ($0) and verifying urea concentration with a $15 refractometer, saving upwards of $3,000.

Mandatory No-Start Lockout & DEF Crystallization Alert

CRITICAL WORKSHOP WARNING: Environmental regulations enforce a permanent engine no-start lockout under persistent P20EE faults!

MANDATORY PROTOCOL: When P20EE is verified, federal and European regulations mandate that the vehicle display an irreversible restart prevention countdown (e.g. 'No Restart in 800 km'). Once this counter reaches 0 km, the ECM locks the starter motor relay, preventing engine cranking until the fault is repaired and authenticated via a protected scan tool adaptation procedure. Furthermore, never flush the DEF system with tap water; mineral deposits instantly poison the expensive zeolite catalyst core, requiring complete exhaust replacement!

PLATFORM ARCHITECTURE

Meest getroffen motoren en injectieplatformen

Deze foutcode treedt hoofdzakelijk op bij de volgende common-rail dieselplatforms. Raadpleeg hieronder uw motorfamilie voor fabrieksspecificaties en onderdeelnummers:

Ford 6.7L Powerstroke V8 Turbo Diesel

Typisch symptoom: Message cluster countdown 'Speed Limited to 50 MPH in 50 Miles', white crust on tailpipe, P20EE stored

Bekende fabriekszwakte: DEF / AdBlue dosing injector nozzle choked with hard white crystalline urea crust, preventing proper spray atomization

Belangrijk onderdeel:OE BC3Z-5J281-B / Motorcraft DEF Doser Injector & HC3Z-5J299-A Upstream NOx Sensor

VAG 2.0 TDI (EA189 / EA288 Common Rail)

Typisch symptoom: Instrument warning 'AdBlue error: No engine restart in 1000 km', solid wrench icon, failed periodic emissions test

Bekende fabriekszwakte: Downstream NOx smart sensor internal probe thermal aging or degraded non-compliant DEF fluid with refractive index below 32.5%

Belangrijk onderdeel:OE 04L907805L / Continental Gen 3 NOx Sensor & Bosch AdBlue Dosing Module

Mercedes-Benz 2.1 CDI (OM651)

Typisch symptoom: Sprinter dashboard shows 'Engine Start Not Possible in 10 Starts', strong ammonia odor from exhaust tip

Bekende fabriekszwakte: SCR mixer chamber wall heavy crystallized urea buildup preventing turbulent mixing of exhaust gas and ammonia

Belangrijk onderdeel:OE A0009053603 / Continental NOx Sensor & A0004900200 Dosing Valve

BMW 2.0d / 3.0d (N47 / N57 / M47N)

Typisch symptoom: iDrive warning 'Incorrect Diesel Exhaust Fluid - No engine start in 200 mi', SCR catalytic efficiency below 70%

Bekende fabriekszwakte: Exhaust gas temperature sensor (EGT) drift before SCR brick causing ECU to under-dose urea at low load

Belangrijk onderdeel:OE 13628589846 / Bosch NOx Sensor & SCR Catalyst Assembly
WORKSHOP MASTER TEARDOWN GUIDE

AdBlue DEF Crystallization & No-Start Reset Guide

AdBlue countdown warning or engine restart prohibited? Diagnose urea injector crystallization deposits, DEF pump pressure faults and emergency resets.

Read Full Master Guide →
THEORY OF OPERATION

Stuurstroomcircuit & Actuatorlogica

1. Dynamic In-Demand Fuel Metering

The SCR system injects an aqueous urea solution (32.5% high-purity urea in demineralized water) into the hot exhaust gas stream. Under exhaust temperatures exceeding 200°C, the urea undergoes thermolysis and hydrolysis to produce ammonia (NH3). Inside the SCR catalytic ceramic core (coated with copper/iron zeolite or vanadium pentoxide), the ammonia reacts selectively with harmful nitrogen oxides (NO and NO2) to produce harmless diatomic nitrogen (N2) and water vapor (H2O). Dual ceramic smart NOx sensors communicate emission values to the ECM via dedicated high-speed CAN-bus networks.

2. Closed-Loop PID Deviation Monitoring

The ECM runs continuous closed-loop SCR efficiency monitoring whenever exhaust temperature is between 220°C and 450°C and exhaust mass flow is stable. The ECM integrates upstream NOx mass against downstream NOx mass over an observation window. If: Efficiency = (NOx_In - NOx_Out) / NOx_In < 0.70 (70%) across two consecutive drive cycles, DTC P20EE is confirmed. Under environmental regulations, the ECM triggers an instrument cluster countdown (e.g. 'Engine Restart Prevented in 800 km / 500 miles') that permanently disables starter cranking once the countdown reaches zero.

3. Diagnostic Trap: Normally Open (NO) vs Normally Closed (NC) Valves

Chemical Contamination vs Hardware Failure: P20EE is rarely a broken catalytic converter! Over 75% of workshop cases are caused by poor-quality or diluted DEF/AdBlue fluid (refractometer reading < 32.5%), white crystallized urea deposits choking the injector nozzle or mixer tube, a drifting downstream NOx sensor, or low exhaust temperatures caused by a stuck-open engine thermostat.

ENGINEERING SPECIFICATIONS

Elektrische & Hydraulische referentiewaarden

Solenoid Coil DC ResistanceAdBlue Dosing Injector Coil Resistance: 12.0 - 16.0 Ω @ 20°C; Heated DEF Line Resistance: 1.8 - 3.5 ΩMeasured @ 20°C across terminals 1 & 2
Insulation Resistance> 10 MΩ measured between NOx sensor controller pins and exhaust metal chassis (tested @ 250V/500V DC)Between terminals and pump body (ground)
Operating Supply VoltageNOx Sensor Controller Operating Voltage: 12.0 V - 14.5 V DC; DEF Dosing Pump Supply: 12.0 VHigh-side feed from ECM / main relay
PWM Frequency StandardHigh-Speed CAN-bus (J1939 / ISO 11898 @ 500 kbps) communicating NOx ppm and O2 concentrationSquare-wave PWM modulation
Idle Duty Cycle (Warm Engine)DEF Fluid Concentration Specification: 32.5% ± 0.7% Urea (Refractometer Index: 1.3814 - 1.3843 @ 20°C)Nominal baseline at 250–350 bar
Full-Load Duty Cycle (WOT)Nominal SCR NOx Conversion Efficiency: 85% to 98% under normal highway operating temperatures (250°C-400°C)Maximum high-speed fuel delivery demand
Low-Pressure Feed SupplyRegulated DEF Dosing Pressure: 4.5 - 5.5 bar (65 - 80 psi) generated by the electric dosing unit pumpMeasured at pump fuel inlet
Internal Cascade BackpressureExhaust Temperature Light-Off Threshold: SCR dosing commences strictly when EGT exceeds 200°CControlled by overflow cascade valve
PROCEDURAL PROTOCOL

Stap-voor-stap Werkplaatsprotocol

STEP 1

Test DEF / AdBlue Fluid Quality with an Optical Refractometer

Draw a small sample of fluid from the vehicle's DEF tank. Place two drops on the prism of an automotive optical refractometer calibrated for AdBlue (AUS 32). Read the urea concentration percentage. High-quality fluid must read exactly 32.5% ± 0.7% (refractive index ~1.382). If the fluid reads below 31% (diluted with water) or above 34% (evaporated), drain the tank completely, flush with distilled water, and refill with fresh ISO 22241 certified DEF.

STEP 2

Inspect DEF Dosing Injector for White Urea Crystallization

Unbolt the DEF dosing injector from the exhaust downpipe. Inspect the injector nozzle face and exhaust mixing chamber. Heavy white, chalky crystallized urea buildup indicates a leaking injector needle or insufficient exhaust heat. Soak the injector tip in warm distilled water (60°C) to dissolve the crystals. Never chip crystals with metal tools, as this damages the microscopic spray holes.

STEP 3

DEF Dosing Quantity & Pressure Test

Place the unbolted DEF dosing injector into a clean graduated glass beaker. Connect the scan tool and navigate to Special Functions -> 'DEF / AdBlue Dosing Quantity Test'. Command a 3-minute injection test. Verify that the dosing pump maintains 4.5-5.5 bar pressure and that the delivered fluid volume matches factory specifications (typically 45-60 mL with an even, conical spray pattern).

STEP 4

Dual NOx Sensor Live Data Comparison & Offset Check

With the vehicle at highway cruising speed (> 80 km/h) and exhaust temperatures above 250°C, graph Upstream NOx Sensor (ppm) and Downstream NOx Sensor (ppm). When the DEF system doses, downstream NOx should plummet to under 20-50 ppm while upstream reads 300-600 ppm. If downstream NOx tracks upstream NOx closely despite verified DEF dosing, the downstream sensor is poisoned or the SCR catalyst is dead.

STEP 5

Verify Downstream NOx Sensor Zero-Offset During Deceleration

Perform an extended closed-throttle deceleration (overrun fuel cutoff) from 100 km/h down to 40 km/h. During fuel cutoff, engine-out NOx is zero. Both upstream and downstream NOx sensors must drop to 0 ± 15 ppm. If the downstream sensor remains stuck at 60-100 ppm during zero-fuel overrun, the sensor has suffered internal zero-point drift and must be replaced.

STEP 6

Exhaust Temperature Profile & Catalyst Thermal Check

Verify that the SCR catalyst inlet temperature exceeds 220°C under cruise. If the engine coolant thermostat is stuck open and the engine runs at 70°C, the exhaust never achieves the thermal activation window required for the catalytic reduction reaction, setting false P20EE codes.

COMPONENT-LEVEL REPAIR

Reparatie op hardwareniveau & Onderdelenlijst

Selective Catalytic Reduction (SCR) Exhaust Aftertreatment & DEF Dosing

Bosch Denoxtronic DEF / AdBlue Urea Dosing Valve (Injector)

0 444 021 024 / 0 444 021 048

Atomizes liquid urea into exhaust stream ahead of SCR catalyst under 5.0 - 8.5 bar pump pressure

OEM: Protocol: Inspect tip for cauliflower-like white crystal buildup; clean in warm deionized water (60°C)
Continental / Vitesco Smart NOx Sensor & Control Module - Downstream

5WK9 6688A / A0009053503 / 059 907 807 J

Measures tailpipe NOx concentration (ppm) to verify SCR reduction catalytic efficiency

OEM: Protocol: Replace if sensor probe ceramic heater circuit fails or output locks at high ppm
DEF Dosing Valve High-Temperature Exhaust Flange Clamp & Gasket

OEM V-Band Exhaust Clamp (Make-specific)

Prevents corrosive urea liquid and exhaust leakage at dosing valve mounting bung

OEM: Protocol: Replace if crusty white crystallizations appear around the injector base
Workshop Technical & Economic Benchmark: NOX sensor boss Hex 22mm: 45 - 55 Nm (apply high-temperature anti-seize strictly to threads, not on sensor sniffer tip); DEF dosing injector clamp: 5.5 - 7.0 Nm; Optical DEF refractometer.
LIVE WORKSHOP TOOL

Interactieve Common Rail Tolerantiecalculator

DEF / AdBlue Concentration & Quality Refractometer Guide

Test DEF concentration: Standard ISO 22241 specification requires precisely 32.5% ±0.7% urea in deionized water. Fluid below 31% triggers P20EE catalyst efficiency faults.

📐 Factory Engineering Tolerance: Standard Urea Concentration: Exactly 32.5% (Refractive Index 1.3829)
CALIBRATION RELEARN

Pomp-adaptatiereset & Inleer-proefrit

Following DEF tank replenishment, injector cleaning, NOx sensor replacement, or SCR catalyst replacement for DTC P20EE:

1. Clear all active and pending diagnostic trouble codes from the Engine Control Module.

2. Access ECM Special Functions -> 'SCR System Reset / Quality Verification Test / Reset No-Start Warning'.

3. If a new NOx sensor was installed: execute 'Reset Learned Values for NOx Sensor 1 / 2'.

4. Perform the mandatory SCR Adaptation Drive Cycle: drive on the highway at a sustained 80-110 km/h for at least 25 to 35 minutes with exhaust temperatures maintained above 250°C to allow the ECM to run its complete SCR conversion efficiency test and extinguish the restart countdown warning.

DIFFERENTIAL DIAGNOSIS

Differentiaaldiagnose & Gerelateerde fouten

P204F

Reductant System Performance (Bank 1)

P207F

Reductant Quality Performance

P229E

NOx Sensor Circuit (Bank 1 Sensor 2)

P20EE

SCR NOx Catalyst Efficiency Below Threshold (Bank 1)

FIELD REPAIR REPORTS

Praktijkgevallen uit de werkplaats

CASE #1

2017 BMW X5 xDrive30d (F15 N57)(152,000 km)

Reported Complaint:Dashboard warning '200 miles until engine will not restart - AdBlue system fault'; DTC P20EE stored.
Teardown Root Cause:DEF fluid refractometer check showed 32.6% urea (specification pass). Removed Bosch DEF dosing valve from exhaust downpipe and found nozzle tip completely choked with crystalline urea deposits resembling cauliflower. Dosing spray pattern was restricted to a weak dribble.
Repair Solution:Immersed dosing valve in 60°C deionized water bath for 20 minutes until deposits completely dissolved. Performed actuator spray test (3 distinct fine atomized cones verified). Road tested 40 km: downstream NOx dropped from 420 ppm to 25 ppm (>94% reduction efficiency), clearing the no-start counter.
DIAGNOSTIC FAQ

Veelgestelde technische vragen

Wat betekent motorfoutcode P20EE?

Foutcode (DTC) P20EE geeft aan dat de motorregeleenheid (ECM/PCM) heeft gedetecteerd dat het conversierendement van de selectieve katalytische reductie (SCR) NOx-katalysator (Bank 1) onder de gekalibreerde emissiegrenswaarden is gedaald. Moderne Euro 6- en EPA Tier 3-dieselvoertuigen maken gebruik van een SCR-katalysator die stroomopwaarts wordt gevoed door een AdBlue/DEF-doseerklep. Een stroomopwaartse slimme NOx-sensor meet de ongereinigde uitstoot direct na de motor, terwijl een stroomafwaartse NOx-sensor de restuitstoot bij de uitlaat meet. De ECM berekent continu het actuele rendement. Zakt het NOx-reductierendement tijdens een gestandaardiseerde testcyclus onder de 70% (nominale streefwaarde > 90%-95%), dan wordt DTC P20EE opgeslagen en treedt een aftelprocedure voor herstartblokkade in werking.

Wat zijn de meest voorkomende symptomen van P20EE?

Check Engine Light (MIL) and DEF / AdBlue warning symbols illuminated on the dashboard, Instrument cluster displaying an urgent message: 'Engine Restart Prevented in XXX km / miles', No noticeable change in engine power, drivability, or fuel economy (engine runs cleanly, but emissions exceed limits), Audible crystalline crunches or white powder deposits visible around the DEF dosing injector exhaust flange, Vehicle entering permanent starter lockout (no-crank condition) once the distance countdown reaches zero, Scan tool live data displays downstream NOx sensor ppm reading nearly as high as upstream NOx sensor ppm.

Wat veroorzaakt P20EE bij een dieselmotor?

Contaminated, diluted, or expired Diesel Exhaust Fluid (DEF/AdBlue) with urea concentration below 32.5%; Heavy white rock-like urea crystallization (biuret deposits) clogging the dosing injector tip or exhaust decomposition pipe; Defective, drifting, or poisoned downstream (post-SCR) smart NOx sensor over-reporting residual NOx ppm; Insufficient DEF injection pressure or restricted DEF dosing unit pump failing to deliver required 5.0 bar pressure; Thermal efficiency loss due to a stuck-open coolant thermostat keeping exhaust gas temperatures below 200°C; Chemical poisoning or thermal degradation of the SCR catalyst ceramic substrate due to sulfur, engine oil ash, or coolant leaks.

Is het veilig om te rijden met actieve code P20EE?

🟡 Pas op: Noodloop actief / Bezoek werkplaats

Wat kost het repareren van foutcode P20EE?

De gemiddelde reparatiekosten voor storingscode P20EE hangen af van de exacte oorzaak en het diagnoseniveau: Niveau 1 (Klein onderhoud / Doe-het-zelf): € 40 - € 120: AdBlue/DEF-tank leegpompen en vullen met verse vloeistof conform ISO 22241, of reinigen van ureumkristallen op de AdBlue-doseerklep. (Sensorreiniging, brandstoffilter vervangen, zekering controleren of contacten reinigen.); Niveau 2 (Vervanging onderdeel): € 280 - € 550: Vervanging van de stroomopwaartse of stroomafwaartse NOx-sensor (slimme sensor van Continental / Bosch). (Vervanging enkel onderdeel (drukregelventiel, doseereenheid of gereviseerde verstuiver).); Niveau 3 (Revisie hoofdsysteem): € 1.400 - € 3.200+: Volledige vervanging van het SCR-katalysatorelement of de complete AdBlue-tankinheid inclusief opvoerpomp. (Revisie hogedrukpomp, nieuwe OEM-verstuivers of vervanging DPF-roetfilter.). Werkplaatsreferentietarieven. Meer dan 70% van de gevallen wordt opgelost binnen niveau 1 of 2 zonder vervanging van complete subeenheden.

Can bad AdBlue/DEF trigger DTC P20EE?

Yes! In fact, diluted, contaminated, or degraded DEF is the single most common cause of P20EE. If the fluid contains less than 32.5% urea (due to water contamination or heat degradation), insufficient ammonia is produced in the exhaust, causing NOx conversion to fail.

How do I remove the 'Engine Restart Prevented' warning?

The warning cannot be cleared simply by pressing 'Clear DTCs'. The physical cause (crystallization, sensor, or fluid) must be repaired, followed by initiating the 'SCR System Verification Drive' via scan tool and driving at highway speeds for 20-30 minutes until the ECM confirms efficiency > 85%.

Will a faulty downstream NOx sensor cause P20EE?

Yes. If the downstream NOx sensor suffers calibration drift and over-reports tailpipe NOx by even 50 ppm, the ECM's internal mathematical equation calculates that the catalyst is failing, setting a false P20EE even when the catalyst is physically perfect.