12697966
HITACHI 12697966 ТНВД Топливный Насос GM Ecotec 2.0T 2.5L SIDI
12697966, 12641847, 12633492, 12633115, 12639694Integrated Pulse-Width Modulated Spill Valve Solenoid-200 barОбзор детали
The Hitachi 12697966 (GM OE 12641847 / 12633492) is the genuine original equipment high-pressure mechanical fuel pump for General Motors 2.0L Turbo LTG, 2.5L LCV, and 3.6L LGX SIDI engines. Mounted directly on the rear of the cylinder head and actuated by the exhaust camshaft lobe via a roller lifter, this pump delivers 200 bar (2900 psi) direct injection pressure. Failure triggers extended cold cranking, engine stumbling under full throttle, and diagnostic trouble codes P0087 and P0089.
OIL DILUTION & ROLLER TAPPET SCUFFING HAZARD: On GM 2.0T LTG and 2.5L SIDI engines, worn internal high-pressure pump plunger seals allow pressurized liquid fuel to leak past the cylinder head into the crankcase. This causes severe oil dilution, thin oil viscosity, and catastrophic rod bearing failure. Furthermore, always replace the roller lifter (GM OE 12612289) during pump replacement; installing a new HPFP on a scored camshaft lobe will ruin the new pump immediately.
Применяемость к авто и двигателям
Технические характеристики
| Параметр | Значение |
|---|---|
| Pump Generation | Hitachi Radial Plunger High-Pressure Mechanical Fuel Pump |
| Operating Rail PressureОсн. параметр | |
| Cam Drive Type | Exhaust Camshaft Tri-Lobe via Roller Lifter (GM 12612289) |
| Flow Regulation Control | Integrated Pulse-Width Modulated Spill Valve Solenoid |
| Pump Flange Mounting Torque | 12 N·m + 45° (Even two-stage torque) |
| High Pressure Pipe Flare Nut Torque | 30 N·m |
| Tightening Torque | 30 N·m |
| Момент затяжки прижимной скобы | 12 N·m |
| Primary OEM Reference | 12697966, 12641847, 12633492, 12633115 |
| Engine Emission Compliance | Euro 6 / LEV III / Tier 3 Bin 30 |
| Standard Industrial Warranty | 12 Months / Unlimited Mileage |
| Рабочее давлениеОсн. параметр |
Совместимый ТНВД (Топливный контур в сборе)
Работает в одном контуре Common Rail высокого давления. При падении давления (P0087) проверьте подачу насоса перед заменой форсунок.
Рекомендации по установке
Необходимый инструмент: 10mm socket, extension, and ratchet for pump flange mounting bolts, Torque wrench calibrated for 10-35 N·m range, Line flare wrench for high-pressure fuel pipe union nuts, Clean engine oil or assembly lube for roller lifter and O-ring seal, Eye protection and absorbent shop towels for high-pressure fuel release
- Disconnect battery negative terminal; remove fuel pump relay/fuse and crank engine to relieve static line pressure.
- Wrap shop towels around high-pressure fuel line fitting and slowly loosen flare nut to bleed residual rail pressure safely.
- Disconnect electrical wiring connector from the fuel metering spill valve solenoid.
- Disconnect low-pressure fuel feed line quick-connector from pump inlet.
- Loosen the two pump flange bolts alternately in half-turn increments to relieve camshaft spring tension evenly.
- Extract pump from cylinder head; remove roller lifter GM 12612289 and inspect for surface scoring or bearing play; replace if worn.
- Clean mounting bore thoroughly; coat new pump O-ring seal with clean engine oil.
- Rotate engine so the camshaft driving lobe is on its base circle (lowest lift point).
- Insert lubricated roller lifter, seat pump square, and thread mounting bolts finger-tight.
- Torque mounting bolts alternately in two progressive steps to 12 N·m plus a 45-degree angle turn.
- Thread high-pressure steel line flare nut by hand to prevent cross-threading; torque nut to 30 N·m.
- Reconnect low-pressure feed line and wiring harness; cycle key on 3 times to prime system and check for fuel leaks.
- Camshaft Base Circle Mandate: Always rotate engine so the driving cam lobe is at its lowest position before torquing pump bolts to prevent binding internal plunger.
- Mandatory Oil Flush: If replacing pump due to gasoline smell on dipstick or rising oil levels, flush engine oil and filter immediately to protect rod bearings.
- Roller Lifter Inspection: Always renew the roller lifter alongside the pump; a worn lifter flat spot will gouge the new pump plunger within miles.
Коды неисправностей (DTC) и протоколы диагностики
Основные диагностические коды неисправностей (DTC), возникающие при износе, замыкании цепи или отклонении калибровки данной форсунки Common Rail:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Кросс-номера и совместимость
Смежные артикулы, модификации одной платформы и известные ограничения совместимости.
Технические протоколы диагностики и обслуживания
Проверенные сервисные процедуры, пороговые значения тестов и регламенты для данного узла.