OBD-II DİZEL ATÖLYE PROTOKOLÜ8-10 min read

P0236Turbo ve EmişYüksek Önem💡 Motor Arıza Lambası Yanıyor

P0236: P0236 Turbo Takviye Basınç Sensörü A Devresi Aralık/Performans

FuelPartsDB Teknik Mühendislik EkibiYayınlanma: March 15, 2026Son Güncelleme: October 3, 2026Uzmanlık: Common Rail Sistemleri

Arıza Teşhis Kodu (DTC) P0236, Motor Kontrol Modülünün (ECM/PCM) Manifold Mutlak Basınç (MAP) / Aşırı Doldurma (Boost) Basınç Sensörü 'A' devresinde bir tutarlılık, mantıksallık veya dinamik tepki korelasyon hatası tespit ettiğini gösterir. Modern ortak hatlı (common rail) turbo dizel platformlarında MAP sensörü, değişken geometrili turboşarj (VNT) kanatçık konumunu yönetmek ve yakıt püskürtme miktar sınırlarını hesaplamak amacıyla intercooler çıkışındaki emme havası yoğunluğunu izler. P0236 kodu, temel olarak Kontak Açık - Motor Kapalı (KOEO) barometrik tutarlılık denetimi sırasında; MAP sensörü ölçümünün ECM dahili Barometrik Basınç (BARO) sensöründen veya ortam hava basıncı sensöründen 7.0 - 10.0 kPa (70 - 100 mbar) aralığından daha fazla sapması durumunda tetiklenir. Ayrıca, yüksek motor yükü altında ölçülen fiili aşırı doldurma basıncının yükselme süresi, kalibre edilmiş eşikleri aşarak hedeflenen basınç değerinin gerisinde kaldığında da kaydedilir.

🚗 SÜRÜCÜ REHBERİ VE ONARIM PROTOKOLÜ

🚗 Sürüş Güvenliği, Tahmini Onarım Maliyeti ve Doğrulama

🟢 Bilgi: Sürüşe Uygun / Emisyon Kontrolü

01
🚦 Sürüş Güvenliği ve Mekanik Risk
Acil mekanik değerlendirme ve çekici gereksinimi
Turbo Aşırı Doldurma Basınç Sensörü 'A' Devresi Aralık / Performans - Gecikmeli Tepki
Manifold Mutlak Basınç (MAP) veya Aşırı Doldurma Basınç Sensörü gecikmeli tepki veriyor ya da motor çalışmıyorken atmosfer basıncıyla uyuşmayan veriler üretiyor. Araç kısıtlı turbo basıncı ile çalışacaktır. Mevcut sürüşünüzü güvenle tamamlayabilirsiniz.
SÜRÜŞE DEVAM EDİLMESİ DURUMUNDA MOTOR RİSKLERİ:Hava-yakıt oranının bozulmasından kaynaklanan yüksek kurum üretimi, kademeli dizel partikül filtresi (DPF) tıkanması ve tek şeritli yollarda yetersiz sollama ivmelenmesi.
02
💰 Servis Onarım Bütçesi
Beklenen parça değişimi ve servis işçilik maliyet kademeleri
Küçük Bakım / Filtre Temizliği750 TL - 2.000 TL: Yağlanmış sensör ucunun yağsız kontak spreyi veya MAF temizleyici sprey ile temizlenmesi.
Sensör temizliği, yakıt filtresi değişimi, sigorta kontrolü veya kablo soketi temizliği.
Valf / Sensör Değişimi2.500 TL - 7.500 TL: Orijinal yeni Bosch/Continental aşırı doldurma (boost) basınç sensörü değişimi.
Tek bileşen değişimi (basınç regülatörü, dozaj valfi veya revizyonlu enjektör).
Ağır Onarım / Pompa ve Enjektörler12.000 TL - 25.000 TL: Turbo basınç kaçağı onarımı (patlak intercooler hortumu, çatlak emme manifoldu değişimi).
Yüksek basınç pompası revizyonu, yeni OEM enjektör takımı veya DPF değişimi.
Servis referans fiyatları. Arızaların %70'inden fazlası komple parçalar değiştirilmeden Seviye 1 veya 2 dahilinde çözülür.
03
🧰 Hızlı Görsel ve Fiziksel Kontroller
Servisi aramadan önce aletsiz 5 dakikalık hızlı kontrol
1Sensörü sökün ve algılayıcı ucunu inceleyin: EGR sisteminden gelen siyah yağlı kurumla kaplanmışsa, yağsız kontak spreyi ve yumuşak kıllı bir fırça ile nazikçe temizleyin.
2Aşırı doldurma basınç kaçaklarını kontrol edin: İntercooler hortum bağlantıları etrafında dışarı sızmış siyah yağ kalıntılarını ve yarıkları araştırın.
3Motor KAPALI ve kontak AÇIK (KOEO) konumdayken arıza tespit cihazından canlı değerleri okuyun: Basınç sensörü yaklaşık 100 kPa / 1.0 bar (atmosfer basıncı) değerini göstermelidir.
04
🛡️ Yanıltıcı Arıza Teşhisine Karşı Koruma
Gereksiz parça değişimini önlemek için tamirciye sorulacak sorular
"Ustanıza şunu söyleyin: 'MAP sensörünü yenilemeden önce, patlak intercooler hortumlarını ve kaçakları tespit etmek için lütfen sisteme aşırı doldurma duman testi uygulayın.'"
"Ustanıza şunu söyleyin: 'Sensörü temizledikten sonra, motor kapalı ve kontak açık konumda sıfır ofset barometrik kalibrasyonunu teyit edin.'"
Teknik Not: Yüksek maliyetli parça değişimini onaylamadan önce ustanıza bu soruları yöneltin:

🔧 UZMAN TEKNİSYEN TAVSİYESİ VE ONARIM PROTOKOLÜRAPID ASSESSMENT

30 Saniyelik Hızlı Atölye Triyajı

Temel Belirtiler

Check Engine Light (MIL) illuminated continuously on the dashboard
Sluggish engine acceleration, noticeable throttle lag, and lack of top-end pulling power
Engine entering Limp-Home mode with boost pressure restricted and maximum RPM capped (~2,800 RPM)

En Olası Nedenler

Internal calibration drift (zero-offset shift) or micro-fracture of the MAP sensor piezoresistive silicon diaphragm
Thick accumulation of oily crankcase sludge and EGR carbon plugging the sensor's physical sensing nipple
High electrical contact resistance, terminal pin fretting corrosion, or loose crimps in the MAP sensor harness connector

İlk Gerekli İşlem

Connect scan tool live telemetry: compare Target Fuel Rail Pressure vs Actual Rail Pressure and log metering valve command PWM duty cycle during idle and road load.

🛠️ Geri Dönüş (Back-Leak) Denge Analizörü

Expensive Diagnostic Pitfall & Technical Reality

❌ Yaygın servis yanılgısı:

P0236 proves the turbocharger turbine or wastegate mechanism has failed and the turbocharger must be replaced as an entire assembly ($1,500 - $2,600).

🔍 Teknik ve hidrolik gerçeklik:

P0236 is a plausibility range code: the Manifold Absolute Pressure (MAP) sensor electrical circuit is complete, but its signal does not correlate logically with ambient barometric pressure or engine operating speed. In over 78% of verified cases, the turbocharger itself is in perfect working order. The root cause is a small vent foam filter plugged with road grime on the N75 vacuum regulator solenoid, a split silicone vacuum hose leading to the wastegate/VNT actuator, or heavy oily carbon sludge plugging the tiny sensing port of the MAP sensor on the intake manifold.

💡 Teknik doğrulama protokolü:

Unnecessarily spending $2,000 on a new turbocharger vs clearing the sensor pressure port ($0) or replacing cracked vacuum hoses ($25), saving over $1,900.

Turbocharger Overspeed & Intercooler Burst Hazard

CRITICAL WORKSHOP WARNING: A drifting or under-reporting MAP sensor directly endangers the turbocharger compressor and intake piping!

MANDATORY PROTOCOL: If the MAP sensor under-reports true intake pressure (for instance, reading 180 kPa when actual manifold pressure has surged to 260 kPa), the ECM's closed-loop boost controller commands the VNT turbine vanes to remain aggressively closed to chase the target. This drives the turbocharger into extreme overspeed (> 220,000 RPM) and thermal choke, resulting in compressor wheel fatigue burst, journal bearing seizure, or catastrophic bursting of the aluminum/plastic intercooler end-tanks. Never operate under heavy boost until MAP calibration is cross-verified with a mechanical pressure gauge.

PLATFORM ARCHITECTURE

En Çok Etkilenen Motorlar ve Enjeksiyon Sistemleri

Bu arıza kodu öncelikle aşağıdaki common rail dizel platformlarını etkiler. Fabrika arıza modelleri ve parça numaraları için motor ailenizi inceleyin:

VAG 2.0 TDI (EA189 / EA288 Common Rail)

Tipik Belirti: Intermittent limp mode when passing on highway, flashing glow plug lamp, engine smooths out after ignition cycle

Bilinen Fabrika Arıza Modeli: Intercooler intake pipe MAP sensor sampling port plugged with oily carbon sludge, dampening dynamic pressure response

Temel Alt Parça:OE 038906051K / Bosch 0 281 002 401 3-Bar / 4-Bar Manifold Absolute Pressure Sensor

VAG 2.0 TDI (EA189 / EA288 Common Rail) Motor Teknik Merkezini İncele →

Ford / PSA 1.6 TDCi (DV6ATED4 / DV6TED4)

Tipik Belirti: Delayed turbo boost response under acceleration, mild whistling noise, Check Engine light illuminated

Bilinen Fabrika Arıza Modeli: Boost sensor piezoresistive element zero-point calibration drift, or hairline boost leak at intercooler silicone elbow hose

Temel Alt Parça:OE 9639381480 / Bosch 0 261 230 043 Boost Pressure Sensor & Intercooler Hose

Ford / PSA 1.6 TDCi (DV6ATED4 / DV6TED4) Motor Teknik Merkezini İncele →

BMW 2.0d / 3.0d (N47 / N57 / M47N)

Tipik Belirti: Drivetrain malfunction warning, sluggish throttle response, DDE fault code 41AA / P0236 stored

Bilinen Fabrika Arıza Modeli: Intake manifold heavy carbon fouling creating localized pressure drop across MAP sensor orifice

Temel Alt Parça:OE 13627792260 / Bosch 0 281 002 961 Intake Manifold Pressure Sensor

BMW 2.0d / 3.0d (N47 / N57 / M47N) Motor Teknik Merkezini İncele →

Mercedes-Benz 2.1 CDI (OM651)

Tipik Belirti: Top speed restricted to 60 mph on highway, harsh automatic transmission shifts, engine light on

Bilinen Fabrika Arıza Modeli: Cracked charge air pipe seam or MAP sensor internal bridge drift causing rationality failure against atmospheric BARO sensor

Temel Alt Parça:OE A0061539928 / Bosch 0 281 002 844 Boost Pressure Sensor

Mercedes-Benz 2.1 CDI (OM651) Motor Teknik Merkezini İncele →

WORKSHOP MASTER TEARDOWN GUIDE

Diesel Boost Pressure Sensor (MAP) Diagnostics Guide

Workshop diagnostic guide for turbo boost sensor fault codes P0236, P0237, and P0238. Manifold pressure testing, 5V reference, and VNT vane correlation.

Read Full Master Guide →

THEORY OF OPERATION

Kontrol Devresi ve Aktüatör Çalışma Mantığı

1. Dynamic In-Demand Fuel Metering

The Boost Pressure Sensor 'A' utilizes a piezoresistive silicon micromachined diaphragm exposed to manifold air pressure on one side and an internal sealed reference vacuum on the other. It is wired into a three-pin circuit: 5.0V regulated reference supply, dedicated analog sensor ground, and analog signal output (typically 0.5V to 4.5V corresponding to 20 kPa to 300+ kPa absolute pressure). At sea level ambient conditions (101.3 kPa absolute), sensor output rests at approximately 1.65V to 1.85V. Under peak turbocharger boost (220 to 280 kPa absolute / 1.2 to 1.8 bar gauge boost), output voltage climbs smoothly toward 3.80V to 4.30V.

2. Closed-Loop PID Deviation Monitoring

The ECM runs continuous dual-phase plausibility checks: (1) Static KOEO Zero-Drift Check: When ignition is switched ON with engine stopped, intake manifold pressure must equal local ambient barometric pressure. If MAP differs from BARO by > 10 kPa for more than 2 seconds, the sensor is flagged as zero-drifted; (2) Dynamic Correlation Check: Under full-load acceleration, the ECM models expected air mass from engine speed, intake temperature, and MAF airflow. If measured boost pressure fails to track modeled manifold pressure within ±25 kPa over a 4-second observation window, DTC P0236 is recorded and Limp-Home fueling limits are engaged.

3. Diagnostic Trap: Normally Open (NO) vs Normally Closed (NC) Valves

Piezoresistive Diaphragm Calibration Drift: P0236 is rarely a broken wire; it is overwhelmingly caused by physical sensor degradation. Over years of service, oily crankcase blow-by fumes (PCV) and EGR soot cake the microscopic pressure port, creating a viscous gel layer that slows pressure transmission to the silicon diaphragm. Alternatively, thermal cycling can induce hysteresis or micro-fractures in the internal piezoresistive bridge, permanently shifting the output baseline by 0.3V-0.5V.

ENGINEERING SPECIFICATIONS

Elektriksel ve Hidrolik Fiziksel Standartlar

Solenoid Coil DC ResistancePiezoresistive Bridge Internal Resistance: 1.5 kΩ - 3.5 kΩ measured between 5V Ref and Ground pinsMeasured @ 20°C across terminals 1 & 2

Insulation Resistance> 10 MΩ measured between any sensor pin and engine metal chassis (tested @ 250V/500V DC)Between terminals and pump body (ground)

Operating Supply VoltageECM Regulated 5V Reference Supply: 4.95 V - 5.05 V DC; Sensor Ground Voltage Drop: < 0.05 V DCHigh-side feed from ECM / main relay

PWM Frequency StandardLinear analog DC voltage (0.5V to 4.5V) corresponding to 20 kPa to 300 kPa (or 400 kPa on high-performance diesels)Square-wave PWM modulation

Idle Duty Cycle (Warm Engine)Key-ON Engine-OFF / Sea Level Idle (100 kPa): 1.65 V - 1.85 V; Permissible MAP vs BARO variance: < 7.0 kPa (70 mbar)Nominal baseline at 250–350 bar

Full-Load Duty Cycle (WOT)Full Boost Output @ 250 kPa (1.5 bar boost): 3.65 V - 3.95 V; Maximum permissible signal lag under transient step: < 250 msMaximum high-speed fuel delivery demand

Low-Pressure Feed SupplyMaximum Permissible Signal Wire Resistance: < 0.4 Ω end-to-end between ECM harness connector and MAP sensor plugMeasured at pump fuel inlet

Internal Cascade BackpressureSensor Orifice Clog Threshold: Pressure port bore diameter < 1.8 mm; Caked soot reduction > 30% causes signal lagControlled by overflow cascade valve

PROCEDURAL PROTOCOL

Adım Adım Atölye Teşhis Protokolü

STEP 1

Key-ON Engine-OFF 3-Way Pressure Sensor Rationality Test

Connect a professional scan tool with ignition switched ON and engine OFF. Display live data PIDs for: (1) Manifold Absolute Pressure (MAP); (2) Barometric Pressure (BARO); (3) Pre-Turbo Ambient Pressure. In an un-started engine, all three sensors measure the same atmospheric air. Compare the three values: at sea level, all should read approximately 99-102 kPa. If the MAP sensor differs from BARO by more than 7 kPa (0.07 bar / 1.0 psi), the MAP sensor has suffered irreversible zero-point calibration drift and must be replaced.

STEP 2

Inspect Sensing Orifice for EGR Carbon Sludge Clogging

Unbolt the MAP sensor from the intake manifold or charge pipe. Visually inspect the tiny pressure sampling aperture. In common rail diesels, a mixture of oily PCV blow-by and dry EGR soot frequently cakes over the hole, forming a viscous diaphragm that delays pressure changes. Clean carefully using electrical contact cleaner. Never poke rigid metal picks or wire probes into the hole, as this punctures the microscopic silicon diaphragm instantly.

STEP 3

Regulated Mityvac Bench Pressure & Voltage Test

With the sensor removed or probed in-place, connect a calibrated pressure hand pump (Mityvac) with an accurate digital gauge to the sensor port. Turn ignition ON (5V supply active). Apply 0 kPa, 50 kPa, 100 kPa, and 150 kPa relative gauge pressure. Monitor sensor signal voltage with a precision digital multimeter. Voltage must track factory transfer curves (e.g., ~1.75V @ 0 bar gauge / 100 kPa abs; ~3.05V @ 1.0 bar gauge / 200 kPa abs). If voltage plateaus, lags, or deviates > 0.15V from the transfer curve, discard the sensor.

STEP 4

5V Reference & Sensor Ground Circuit Voltage Drop Test

Disconnect the MAP sensor plug. With ignition ON, measure voltage on the 5V reference pin referenced to battery negative (must read 4.95V-5.05V). Next, measure voltage drop between the harness sensor ground terminal and battery negative (must be < 0.05V / 50 mV). High resistance in the ground circuit offsets sensor signal voltage upward, mimicking a high boost condition.

STEP 5

Smoke Machine Test for Charge-Air Induction Leaks

If the sensor passes electrical bench calibration, connect an automotive smoke generator to the intake tract. Pressurize the system to 1.0 bar. Inspect all silicone boost couplers, intercooler crimp seams, and intake manifold gaskets. A split in an intercooler hose can cause dynamic pressure lag under boost that triggers P0236 despite a functional electrical sensor.

STEP 6

Dynamic Road Test Oscilloscope Boost Response Capture

Back-probe the MAP signal wire with a digital storage oscilloscope. Perform a full-throttle acceleration run in 3rd gear from 1,500 to 3,500 RPM. Verify that the signal voltage rises smoothly from ~1.8V to ~3.8V within 400-600 milliseconds. Look for signal dropouts, excessive noise hash (> 200 mV ripple), or sluggish step-up response indicative of harness terminal fretting or sensor fatigue.

COMPONENT-LEVEL REPAIR

Donanım Onarımı ve Yedek Parça Listesi (BOM)

Pneumatic / Electronic Boost Pressure Control & MAP Feedback Interface

Bosch Combined MAP & Air Temperature Sensor

0 281 002 976 / 0 281 006 059

Measures absolute charge air pressure and manifold temperature to control VNT vane angle

OEM: Protocol: Clean or replace if sensor reading deviates by >50 mbar from ambient barometric pressure at key-on

Pierburg Electro-Pneumatic Boost Pressure Solenoid Valve (N75)

7.00470.07.0 / 1K0 906 627 B

Regulates vacuum supply to VNT actuator; internal venting filter vents vacuum to atmospheric

OEM: Protocol: Replace if internal diaphragm leaks or vent filter is choked with black dust

Heavy-Duty Fluorosilicone Vacuum Tubing Kit (3.5mm & 5.0mm)

Reinforced Vacuum Line Kit

Maintains steady vacuum without heat collapse between vacuum pump, solenoid, and actuator

OEM: Protocol: Replace whenever rubber feels soft, sticky, or cracks under flex

Workshop Technical & Economic Benchmark: Sensor retaining bolt: 3.5 - 4.5 Nm; Handheld vacuum pump with gauge (must pull and hold 600 mbar vacuum); Scan tool MAP vs BARO correlation screen.

LIVE WORKSHOP TOOL

Canlı Common Rail Tolerans Hesaplayıcı

Launch Dedicated Calculator with Factory Tolerances →

CALIBRATION RELEARN

Yüksek Basınç Pompası Adaptasyon Sıfırlama ve Test

Following the replacement or cleaning of the MAP / Boost Pressure Sensor for DTC P0236:

1. Connect the diagnostic scanner and clear all active and pending trouble codes from the ECM.

2. Access ECM Special Functions -> 'Reset Air Mass / Boost Pressure Sensor Adaptation Values'.

3. Switch ignition OFF, disconnect scan tool, and allow the vehicle to rest for 60 seconds until main relay shuts down (power latch phase).

4. Switch ignition ON with engine OFF for 10 seconds; the ECM executes its baseline KOEO barometric correlation routine and registers new zero-drift offsets.

5. Start the engine, bring coolant to operating temperature (> 80°C), and perform a test drive including several wide-open throttle (WOT) accelerations in 3rd and 4th gear to allow closed-loop VNT boost control maps to adapt.

DIFFERENTIAL DIAGNOSIS

Diferansiyel Teşhis ve İlgili Hata Kodları

P0237

Mass or Volume Air Flow Sensor 'A' Range/Performance

FIELD REPAIR REPORTS

Atölye Saha Vaka İncelemeleri

CASE #1

2014 Škoda Superb 2.0 TDI (CFFB 140hp)(188,000 km)

Reported Complaint:Sluggish throttle response with stepped power dropouts under load; DTC P0236 stored in memory.

Teardown Root Cause:Key-On Engine-Off live data showed BARO at 1,008 mbar, but MAP reported 1,180 mbar (172 mbar positive offset error). Removed MAP sensor and discovered sensing port was packed solid with baked oily soot slurry from the EGR system.

Repair Solution:Cleaned sensor orifice with electronic contact cleaner and soft brush without probing the silicon diaphragm. Reinstalled: KOEO reading matched BARO at 1,009 mbar. Full power delivery restored with zero fault codes.

DIAGNOSTIC FAQ

Sıkça Sorulan Teknik Sorular

P0236 motor arıza kodu ne anlama gelir?

P0236 kodunun en yaygın belirtileri nelerdir?

Check Engine Light (MIL) illuminated continuously on the dashboard, Sluggish engine acceleration, noticeable throttle lag, and lack of top-end pulling power, Engine entering Limp-Home mode with boost pressure restricted and maximum RPM capped (~2,800 RPM), Inconsistent or surging acceleration during steady highway cruising under light incline, Excessive black exhaust smoke during tip-in acceleration due to mismatch between modeled air and injected fuel, Scan tool live data displays MAP sensor pressure differing from Barometric Pressure (BARO) with Key-ON Engine-OFF.

Dizel motorda P0236 arızasına ne sebep olur?

Internal calibration drift (zero-offset shift) or micro-fracture of the MAP sensor piezoresistive silicon diaphragm; Thick accumulation of oily crankcase sludge and EGR carbon plugging the sensor's physical sensing nipple; High electrical contact resistance, terminal pin fretting corrosion, or loose crimps in the MAP sensor harness connector; Boost pressure leaks in the charge-air tract (cracked intercooler hose, leaking plastic end-tank, or blown gasket); Sticking variable geometry turbocharger (VGT/VNT) vanes or defective boost control vacuum actuator (N75 solenoid); Defective ECM internal Barometric Pressure (BARO) sensor causing a false differential calculation against a healthy MAP sensor.

P0236 kodu etkinken araç sürmek güvenli midir?

🟡 Dikkat: Koruma Modu Aktif / Servise Gidin

P0236 arıza kodunun tamir maliyeti ne kadardır?

P0236 arıza kodu için tipik onarım maliyetleri kök nedene ve teşhis seviyesine bağlıdır: Seviye 1 (Hafif Onarım / Bakım): 750 TL - 2.000 TL: Yağlanmış sensör ucunun yağsız kontak spreyi veya MAF temizleyici sprey ile temizlenmesi. (Sensör temizliği, yakıt filtresi değişimi, sigorta kontrolü veya kablo soketi temizliği.); Seviye 2 (Parça Değişimi): 2.500 TL - 7.500 TL: Orijinal yeni Bosch/Continental aşırı doldurma (boost) basınç sensörü değişimi. (Tek bileşen değişimi (basınç regülatörü, dozaj valfi veya revizyonlu enjektör).); Seviye 3 (Komple Revizyon): 12.000 TL - 25.000 TL: Turbo basınç kaçağı onarımı (patlak intercooler hortumu, çatlak emme manifoldu değişimi). (Yüksek basınç pompası revizyonu, yeni OEM enjektör takımı veya DPF değişimi.). Servis referans fiyatları. Arızaların %70'inden fazlası komple parçalar değiştirilmeden Seviye 1 veya 2 dahilinde çözülür.

Can I clean a MAP sensor with brake cleaner to fix P0236?

No! Harsh chlorinated brake cleaners contain aggressive aromatic solvents that degrade the silicone gel sealant and delicate bonding wires inside the sensor aperture. Always use dedicated, residue-free electronic contact cleaner or specialized mass air flow sensor cleaner, and let it dry completely.

Why does P0236 cause the car to feel sluggish even at low speeds?

When the ECM detects that the MAP sensor fails its barometric plausibility check, it immediately disables closed-loop turbo boost control as a failsafe. The ECM sets a fixed, conservative fuel injection limit (smoke limitation map based on default air values) and opens the VNT vanes, resulting in severe power loss.

What is the acceptable variance between MAP and BARO readings?

With the engine OFF and ignition ON, the MAP sensor and internal BARO sensor should read within 3.0 to 5.0 kPa (0.03 to 0.05 bar) of each other. Any deviation greater than 7.0 to 10.0 kPa flags DTC P0236 on modern Euro 5/6 and Tier 2/3 diesel platforms.