31686560
BOSCH 31686560 Bomba Alta Presión Volvo XC90 XC60 S90 2.0L Drive-E T6
31478796, 31375549, 0261520295, 0261520476Integrated High-Speed Digital Flow Control Valve (FCV)-200 barEspecificaciones técnicas
| Especificación | Valor |
|---|---|
| Tipo de sistema | Bosch HDP5 Mechanical High Pressure Fuel Pump |
| Presión de servicioDato clave | |
| Actuation Type | Exhaust camshaft dedicated pump lobe driving roller tappet |
| Mounting Flange Bolt Torque | 13 N·m (alternating diagonal progressive tightening) |
| High Pressure Pipe Torque | 25 N·m Flare Nut Connection |
| Flow Control Solenoid Resistance | 9.8 - 12.0 Ω at 20°C (ECU digital metering valve) |
| Códigos de avería frecuentes | P0087 (Fuel Rail Pressure Too Low), P0088 (Rail Pressure Too High), P1193 (Fuel Delivery Error) |
| Workshop Precaution | Lubricate internal roller follower with clean engine oil prior to inserting into cylinder head bore |
Bomba de alta presión compatible (Ensamblaje del circuito de combustible)
Funciona en el mismo circuito de alta presión Common Rail. Al diagnosticar baja presión (P0087), verifique el caudal de la bomba antes de sustituir los inyectores.
Consejos de instalación
- [
- {
- "step": 1,
- "title": "Depressurize Fuel Rail & Remove Acoustic Cover",
- "instruction": "Depressurize fuel rail via diagnostic scan tool or fuse isolation. Remove upper engine acoustic shroud to access the cylinder head rear."
- },
- {
- "step": 2,
- "title": "Disconnect Fuel Feed Hose & Steel High Pressure Union",
- "instruction": "Detach low pressure quick-release fuel supply hose. Unscrew high pressure steel pipe flare nut (25 N·m) with backup counter-wrench."
- },
- {
- "step": 3,
- "title": "Unbolt Mounting Fasteners & Inspect Roller Lifter",
- "instruction": "Loosen two M6 Torx mounting bolts evenly in half-turn increments to relieve spring tension. Remove pump and inspect camshaft roller tappet for scoring."
- },
- {
- "step": 4,
- "title": "Fit New O-Ring, Torque Bolts Evenly & Check For Leaks",
- "instruction": "Install replacement O-ring with fresh engine oil coating. Torque mounting bolts alternately to 13 N·m. Tighten steel line to 25 N·m. Test run engine."
- }
- ]
Codigos de Falla (DTC) y Protocolos de Diagnostico
Codigos de falla de diagnostico (DTC) comunes que se activan cuando este inyector common rail experimenta desgaste, fallas de circuito o desbalance:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Protocolos Técnicos de Diagnóstico y Servicio
Procedimientos de taller verificados, umbrales de prueba y pautas de servicio para este conjunto.