16600-9HP0A
BOSCH 16600-9HP0A Injecteur Haute Pression Nissan Altima Rogue Murano 2.5L 3.5L
0261500073, 0261500074, 16600-6CA0ALaser Multi-Drilled Spray Pattern Atomizer Tip-150 barCompatibilité véhicules et motorisations
| Véhicule | Moteur | Années |
|---|---|---|
| Nissan Altima 2.5L | Nissan 2.0L & 2.5L Direct & Port Injection (MR20DD / QR25DE / QR25DD / PR25DD) | 2019-2024 |
| Nissan Pathfinder 3.5L V6 | Nissan 2.0L & 2.5L Direct & Port Injection (MR20DD / QR25DE / QR25DD / PR25DD) | 2017-2024 |
| Infiniti QX60 3.5L V6 | Nissan 2.0L & 2.5L Direct & Port Injection (MR20DD / QR25DE / QR25DD / PR25DD) | 2017-2024 |
Spécifications techniques
| Spécification | Valeur |
|---|---|
| Operating Principle | Bosch High-Pressure Solenoid Electromagnetic Actuation |
| Fuel Delivery Pressure | Up to 150 bar (15 MPa / 2175 psi) |
| Coil Electrical Resistance | 1.3 - 1.7 Ohm at 20°C |
| Rail Retaining Bolt Torque | 21 N·m M8 Thread Fasteners |
| High Pressure Pipe Torque | 30 N·m High-Pressure Tube Fitting |
| Combustion Chamber Seal | PTFE Virgin Teflon Radial Ring with backup buffer |
| Codes défauts fréquents | P0171 (Lean Bank 1), P0174 (Lean Bank 2), P0300-P0306 (Random Misfire) |
| Primary Diagnostic Check | Check LTFT/STFT fuel trims under high load; clogged nozzle causes severe lean spike |
| Pression de serviceSpéc. clé |
Pompe haute pression associée (Ensemble circuit de carburant)
Fonctionne sur le même circuit haute pression Common Rail. En cas de chute de pression (P0087), vérifier le débit de la pompe avant de remplacer les injecteurs.
Conseils de montage
- [
- {
- "step": 1,
- "title": "Relieve Residual Rail Pressure",
- "instruction": "Disconnect low pressure electric pump fuse. Crank engine 5-10 seconds to dissipate remaining fuel pressure in the high-pressure rail."
- },
- {
- "step": 2,
- "title": "Clean Injector Bores & Remove Old Seals",
- "instruction": "Clean bore thoroughly down to cylinder head seat. Never use metal picks that could scratch internal precision sealing walls."
- },
- {
- "step": 3,
- "title": "Compress Teflon Seals using Calibration Cone",
- "instruction": "Fit brand new Teflon combustion seal using mounting sleeve. Compress ring in step-down calibration die until outer diameter fits cleanly."
- },
- {
- "step": 4,
- "title": "Position Fuel Rail & Torque Bolts",
- "instruction": "Guide fuel rail assembly squarely into cylinder head ports. Tighten rail bolts evenly in two steps up to final torque of 21 N\u00b7m."
- },
- {
- "step": 5,
- "title": "Attach High Pressure Line & Verify Leakage",
- "instruction": "Thread high pressure feed line flare nut finger tight, then tighten to 30 N\u00b7m. Start engine and verify zero fuel misting or weeping."
- }
- ]
Codes de Defaut (DTC) & Protocoles de Diagnostic
Codes de defaut diagnostiques (DTC) courants déclenchés lorsque cet injecteur common rail subit une usure, des pannes de circuit ou une dérive d'étalonnage:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Protocoles Techniques de Diagnostic & Réparation
Procédures d'atelier vérifiées, seuils de test et guides d'intervention pour cet ensemble.