23209-0P010
DENSO 23209-0P010 Iniettore Diretto Toyota Tacoma Lexus RX350 3.5L D-4S
23209-31090, 23209-39215, 297500-0120Slit-Nozzle Dual-Fan High-Atomization Direct Injection ValveSlit-Nozzle Dual-Fan Symmetrical Dispersion200 barApplicazioni Veicolo e Motore
Specifiche Tecniche
| Specifica | Valore |
|---|---|
| Injector Type | Denso High-Pressure Solenoid Direct Fuel Injector (DI) |
| Operating Rail PressureSpecifica Chiave | |
| Nozzle Spray GeometrySpecifica Chiave | |
| Coil Resistance Value | 1.7 to 2.1 Ohms at 20°C (Low Impedance Peak-and-Hold) |
| Fuel Rail Mounting Bolt Torque | 21 N·m |
| High Pressure Pipe Flare Nut Torque | 35 N·m |
| Tightening Torque | 35 N·m |
| Coppia serraggio staffa | 21 N·m |
| Primary OEM Reference | 23209-0P010, 23209-31090, 23209-39215, 23209-31120 |
| Engine Emission Compliance | Euro 6 / LEV III / Tier 3 Bin 30 |
| Standard Industrial Warranty | 12 Months / Unlimited Mileage |
| Pressione di esercizioSpecifica Chiave |
Pompa alta pressione abbinata (Gruppo circuito carburante)
Funziona sullo stesso circuito ad alta pressione Common Rail. In caso di bassa pressione rail (P0087), verificare la portata della pompa prima di sostituire gli iniettori.
Istruzioni di montaggio
Attrezzatura necessaria: 10mm, 12mm, and 14mm sockets, extensions, and torque wrench, 17mm line flare nut wrench for direct fuel pipe connections, Special Service Tool (SST) for Teflon combustion seal installation and sizing, Slide hammer injector puller adapter for carbon-seized DI injectors, Clean engine oil or assembly lubricant for upper O-ring only
- Disconnect negative battery terminal; depressurize fuel system by removing fuel pump fuse and cranking engine for 5 seconds.
- Disconnect direct injector electrical wiring harness connectors.
- Remove upper intake manifold plenum assembly to access the direct injection fuel rails on cylinder bank 1 and bank 2.
- Disconnect high-pressure fuel feed lines from both direct fuel rails.
- Remove fuel rail retaining bolts; extract fuel rail and direct injectors from cylinder head carefully.
- Extract direct injectors from cylinder head pockets; clean injector bores of all carbon debris using non-abrasive brass tool.
- Replace lower white Teflon combustion chamber seal using the expander cone and resizing sleeve; keep Teflon dry.
- Replace upper rail O-rings and backup rings; apply light coat of clean engine oil to upper O-rings.
- Carefully insert direct injectors into cylinder head ports ensuring guide clips align properly.
- Position fuel rail over injectors; install rail mounting bolts and torque evenly to 21 N·m.
- Hand-start high-pressure fuel pipe union nuts; torque high-pressure fuel line nuts to 35 N·m.
- Reassemble intake manifold plenum with new gaskets; reconnect battery and cycle ignition on 3 times to inspect for fuel leaks.
- Teflon Seal Protection: The lower Teflon seal expands when heated in combustion chamber; never touch or grease the seal during installation to avoid combustion blowby.
- Rail Torque Symmetry: Tighten fuel rail bolts gradually in three equal passes across both cylinder banks to ensure uniform injector seating depth.
Domande Frequenti (FAQ)
What are the primary symptoms when 23209-0P010 fails?
Primary symptoms include extended cold engine cranking, severe hesitation under wide-open throttle, rough idle RPM fluctuation, and Diagnostic Trouble Codes P0087 (Fuel Rail/System Pressure Too Low), P0089 (Fuel Pressure Regulator Performance), or P0300 (Random/Multiple Cylinder Misfire).
What is the exact tightening torque for 23209-0P010?
The holding flange mounting torque is 21 N·m, and the high-pressure fuel pipe union nut must be torqued to 35 N·m.
Can I reuse the seals when replacing 23209-0P010?
No. All high-pressure fuel seals, including Viton O-rings and combustion chamber Teflon rings, are strictly single-use. Reusing compressed seals will cause pressurized fuel leaks or combustion blowby into the cylinder head.
Codici Guasto (DTC) e Protocolli Diagnostici
Codici guasto diagnostici (DTC) comuni generati quando questo iniettore common rail presenta usura, problemi ai circuiti o scostamenti:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Protocolli Tecnici di Diagnosi & Assistenza
Procedure d'officina verificate, valori soglia di test e linee guida operative per questo assieme.