DENSO
23209-0T020
Bekijk specs
SolenoidDenso Multi-Point Port Fuel Injection (MPI, 3 bar)Euro 56
DENSO 23209-0T020 Benzine Verstuiver Toyota Corolla Prius 1.8L 2ZR-FE FJ1068
OE-REFERENTIE
23250-0T020, 23209-39145, FJ1068, 842-12349REGELKLEP
-NOZZLE / VERSTUIVERTIP
-RAILDRUK
3.2 barEMISSIEEuro 5 / Euro 6 / SULEV
GARANTIE12 Maanden
02
Voertuig- & motortoepassingen
| Voertuig | Motor | Bouwjaren |
|---|---|---|
| Toyota Prius XW30 / XW50 1.8L Hybrid | Toyota / Lexus 1.8L 2ZR-FE / 2ZR-FXE / 2ZR-FAE (VVT-i & Hybrid) | 2010-2022 |
| Toyota Corolla Hybrid 1.8L | Toyota / Lexus 1.8L 2ZR-FE / 2ZR-FXE / 2ZR-FAE (VVT-i & Hybrid) | 2015-2023 |
| Lexus CT200h ZWA10 | Toyota / Lexus 1.8L 2ZR-FE / 2ZR-FXE / 2ZR-FAE (VVT-i & Hybrid) | 2011-2020 |
03
Technische specificaties
| Specificatie | Waarde |
|---|---|
| part_number | 23209-0T020 |
| oem_reference | 23209-0T020 |
| manufacturer | DENSO |
| system_type | Fuel Injector |
| pressure_rating | 3.2 bar (46.4 psi) |
| operating_temperature | -40°C to +135°C |
| flange_mount_torque | 19 N-m (14 lb-ft) |
| high_pressure_line_torque | 19 N-m (14 lb-ft) |
| diagnostic_dtc | P0171, P0300, P0301, P0174 |
| WerkdrukKernspecificatie |
04
Montagetips
- Depressurize the fuel system completely via diagnostic scan tool or by removing the fuel pump fuse prior to line disassembly.
- Clean all surrounding bracket areas thoroughly using residue-free brake cleaner to prevent abrasive particulate ingress.
- Inspect the mechanical camshaft lobe and roller follower or clean injector bore seating surfaces before hardware alignment.
- Install component using fresh factory O-rings or Teflon combustion chamber seals lubricated only with clean motor oil.
- Torque mounting flange fasteners in alternating increments to 19 N-m (14 lb-ft).
- Torque high-pressure hydraulic tube fittings using a calibrated flare nut wrench to 19 N-m (14 lb-ft).
- Prime low-pressure fuel circuit, cycle ignition key 3-4 times, and inspect for high-pressure hydraulic leaks before road test.
Tips & waarschuwingen:
- Always replace single-use high-pressure metal fuel lines and micro-filter seals whenever disconnected.
- Verify camshaft driving lobe surfaces for scoring or flat spots before installing any mechanical pump.
- Reset long-term and short-term fuel trim adaptations via OBD-II diagnostic scanner after physical replacement.
05
Foutcodes (DTC) & Diagnoseprotocollen
Veelvoorkomende diagnostische foutcodes (DTC's) die optreden wanneer deze common rail-injector slijtage, circuitstoringen of kalibratieafwijkingen vertoont:
P0087Critical
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
P0201 - P0208High
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
P0300 / P0301+High
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
P0088High
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
WERKPLAATS-HANDLEIDINGEN
Technische Diagnose- & Serviceprotocollen
Geverifieerde werkplaatsprocedures, testdrempels en richtlijnen voor deze component.
Werkplaats Diagnoseprotocol
Lees technisch protocolCommon-Rail Verstuiver Retourlektest: Normen & Diagnose
COMMON-RAIL DIESEL WERKPLAATS-SOP
Lees technisch protocolVastzittende Verstuivers Demonteren & Reinigen | SOP
MONTAGE- & INSTALLATIEPROTOCOL
Lees technisch protocol