MOPAR
5184085AC
Vezi specificațiile
SolenoidChrysler Multi-Point Electronic Fuel Injection (MPI 58-psi System)Euro 2556
MOPAR 5184085AC Injector Benzină Jeep Cherokee Dodge Ram 3.6L V6
Platformă motor:Chrysler / Stellantis 3.6L Pentastar DOHC 24V V6 (ERB / ERC) →
COD OE
5184085AD, 05184085AD, 280158233, FJ1147, RL184085AC, 0280158233SUPAPĂ DE COMANDĂ
4-Hole Precision Cone Spray Atomization DirectorDUZĂ PULVERIZATOR
-PRESIUNE ÎN RAMPĂ
4.0 barNORMĂ POLUARETier 2 Bin 5 / Euro 5 / Euro 6 / LEV III
GARANȚIE12 Luni
02
Compatibilitate vehicule și motoare
| Vehicul | Motor | Ani fabricație |
|---|---|---|
| Jeep Grand Cherokee WK2 / Wrangler JL | Chrysler / Stellantis 3.6L Pentastar DOHC 24V V6 (ERB / ERC) | 2011-2023 |
| Dodge Charger / Challenger / Durango | Chrysler / Stellantis 3.6L Pentastar DOHC 24V V6 (ERB / ERC) | 2011-2023 |
| Ram 1500 Classic / DT | Chrysler / Stellantis 3.6L Pentastar DOHC 24V V6 (ERB / ERC) | 2013-2023 |
03
Specificații tehnice
| Specificație | Valoare |
|---|---|
| Tip sistem | Chrysler Pentastar Multi-Point Electronic Fuel Injection (MPI) |
| Operating Fuel Pressure | 4.0 bar (58 psi / 400 kPa regulated rail pressure) |
| Static Fuel Flow Rate | 245 g/min @ 4.0 bar (approximately 235 cc/min @ 3 bar) |
| Electrical Resistance | 12.0 - 13.0 Ohms @ 20°C (High-Impedance Saturated Solenoid) |
| Spray Geometry | 4-Hole Precision Multi-Dispersal Cone Pattern |
| Fuel Rail Fastener Torque | 8 N·m (71 in-lb) fuel rail mounting bolts into lower intake |
| Upper Intake Plenum Fasteners | 10 N·m (89 in-lb) composite intake manifold fasteners |
| Seals Architecture | Upper & Lower High-Fluorine Viton Chemical-Resistant O-Rings |
| Manufacturer | Bosch / Mopar (Tier-1 OEM for Stellantis) |
| Bosch Production Reference | 0280158233 |
| Presiune de lucruSpecificație de bază |
04
Instrucțiuni de montaj
Sfaturi și avertismente:
- Inspect injector retaining wire clips: Ensure retaining clips securely lock the injector shoulder into the fuel rail cup; improper clip engagement allows the injector to pop out under 58 psi rail pressure.
- Always replace lower plenum intake gaskets: The teal silicone upper-to-lower intake manifold gaskets harden and flatten; reuse causes unmetered intake vacuum leaks and P0171/P0174 codes.
- Never use silicone grease on O-rings: Coat strictly with clean engine oil or clean transmission fluid; silicone will damage upstream oxygen sensors.
- Tighten intake manifold fasteners in crisscross sequence: Torque upper intake manifold fasteners in alternating center-outward sequence to 10 N·m (89 in-lb) to prevent warping the composite plastic.
05
Coduri de Eroare (DTC) si Protocoale de Diagnostic
Coduri comune de eroare de diagnosticare (DTC) declansate atunci cand acest injector common rail sufera uzura, defectiuni de circuit sau abateri:
P0087Critical
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
P0201 - P0208High
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
P0300 / P0301+High
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
P0088High
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
PROTOCOALE DE ATELIER
Protocoale Tehnice de Diagnosticare & Service
Proceduri verificate de atelier, praguri de testare și standarde de intervenție pentru acest ansamblu.
Protocol de Diagnoză în Atelier
Citește protocolul tehnicTestul Debitului de Retur la Injectoare: Valori și Diagnoză
SOP ATELIER DIESEL COMMON RAIL
Citește protocolul tehnicExtragere Injectoare Blocate & Decalaminare | FuelPartsDB
PROTOCOL DE ASAMBLARE ȘI INSTALARE
Citește protocolul tehnic