DENSO
23209-37010
Zobrazit parametry
SolenoidDenso Multi-Point Port Fuel Injection (MPI, 4 bar)Euro 56
DENSO 23209-37010 Vstřikovací Ventil Toyota Prius Auris Corolla Lexus CT200h 1.8L 2ZR-FXE FJ1068
Motorová platforma:Toyota / Lexus 1.8L 2ZR-FE / 2ZR-FXE / 2ZR-FAE (VVT-i & Hybrid) →
OE ČÍSLO
23250-37010, FJ1068, 842-12373, 23209-39145ŘÍDICÍ VENTIL
-TRYSKA
-TLAK V RAILU
4 barEMISNÍ NORMAEuro 5 / Euro 6 / SULEV
ZÁRUKA12 Měsíců
02
Použití ve vozidlech a motorech
| Vozidlo | Motor | Roky výroby |
|---|---|---|
| Toyota Prius XW30 / XW50 1.8L Hybrid | Toyota / Lexus 1.8L 2ZR-FE / 2ZR-FXE / 2ZR-FAE (VVT-i & Hybrid) | 2010-2022 |
| Toyota Corolla Hybrid 1.8L | Toyota / Lexus 1.8L 2ZR-FE / 2ZR-FXE / 2ZR-FAE (VVT-i & Hybrid) | 2015-2023 |
| Lexus CT200h ZWA10 | Toyota / Lexus 1.8L 2ZR-FE / 2ZR-FXE / 2ZR-FAE (VVT-i & Hybrid) | 2011-2020 |
03
Technické specifikace
| Parametr | Hodnota |
|---|---|
| part_number | 23209-37010 |
| oem_reference | 23209-37010 |
| manufacturer | DENSO |
| system_type | Fuel Injector |
| pressure_rating | 4 bar (58 psi) |
| operating_temperature | -40°C to +135°C |
| flange_mount_torque | 9 N-m (80 lb-in) |
| high_pressure_line_torque | 21 N-m (15 lb-ft) |
| diagnostic_dtc | P0300, P0301, P0171, P0172 |
| Provozní tlakKlíčový parametr |
04
Pokyny k montáži
- Depressurize the fuel system completely via diagnostic scan tool or by removing the fuel pump fuse prior to line disassembly.
- Clean all surrounding bracket areas thoroughly using residue-free brake cleaner to prevent abrasive particulate ingress.
- Inspect the mechanical camshaft lobe and roller follower or clean injector bore seating surfaces before hardware alignment.
- Install component using fresh factory O-rings or Teflon combustion chamber seals lubricated only with clean motor oil.
- Torque mounting flange fasteners in alternating increments to 9 N-m (80 lb-in).
- Torque high-pressure hydraulic tube fittings using a calibrated flare nut wrench to 21 N-m (15 lb-ft).
- Prime low-pressure fuel circuit, cycle ignition key 3-4 times, and inspect for high-pressure hydraulic leaks before road test.
Tipy a varování:
- Always replace single-use high-pressure metal fuel lines and micro-filter seals whenever disconnected.
- Verify camshaft driving lobe surfaces for scoring or flat spots before installing any mechanical pump.
- Reset long-term and short-term fuel trim adaptations via OBD-II diagnostic scanner after physical replacement.
05
Chybove kody (DTC) a diagnosticke protokoly
Bezne diagnosticke chybove kody (DTC), ktere se spousteji pri opotrebeni, zavade obvodu nebo odchylce kalibrace tohoto vstrikovace common rail:
P0087Critical
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
P0201 - P0208High
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
P0300 / P0301+High
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
P0088High
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
DÍLENSKÉ PROTOKOLY
Technické diagnostické a servisní protokoly
Ověřené dílenské postupy, mezní hodnoty testů a servisní postupy pro tento díl.
Dílenský diagnostický protokol
Číst technický protokolTest Přepadu Vstřikovačů Common Rail: Mezní Hodnoty a Postup
DÍLENSKÝ POSTUP PRO COMMON RAIL DIESEL
Číst technický protokolDemontáž zadřených vstřikovačů a čištění | FuelPartsDB
MONTÁŽNÍ A INSTALAČNÍ PROTOKOL
Číst technický protokol