23209-24010
DENSO 23209-24010 Inyector Alta Presión Toyota RAV4 Camry Lexus 2.0L M20A D-4S
23290-24010, 297500-0120High-Speed Solenoid Actuated Multi-Hole Direct Injection Nozzle-200 barAplicaciones de vehículos y motores
| Vehículo | Motor | Años |
|---|---|---|
| Toyota RAV4 V 2.0L | Toyota / Lexus 2.0L & 2.5L Dynamic Force D-4S (A25A-FKS / A25A-FXS / M20A-FKS) | 2019-2024 |
| Toyota Camry VIII 2.0L | Toyota / Lexus 2.0L & 2.5L Dynamic Force D-4S (A25A-FKS / A25A-FXS / M20A-FKS) | 2018-2024 |
| Lexus ES 200 2.0L | Toyota / Lexus 2.0L & 2.5L Dynamic Force D-4S (A25A-FKS / A25A-FXS / M20A-FKS) | 2019-2024 |
Especificaciones técnicas
| Especificación | Valor |
|---|---|
| Tipo de sistema | Denso Multi-Hole High Pressure Direct Gasoline Injector |
| Presión de servicioDato clave | |
| Spray Pattern | 6-hole optimized high-atomization direct combustion spray |
| Hold-down Torque | 21 N·m Fuel Rail Clamping Bolts📐 Asistente de par y ángulo → |
| High Pressure Pipe Torque | 32 N·m Steel Line Flare Nut |
| Coil Resistance | 1.7 - 2.1 Ω at 20°C (Direct peak-and-hold circuit) |
| Códigos de avería frecuentes | P0300 (Random Misfire), P0301-P0304 (Cylinder Misfire), P0171 (System Lean) |
| Workshop Precaution | Always lubricate upper O-rings with clean engine oil and install new Teflon combustion seal ring before mounting |
Bomba de alta presión compatible (Ensamblaje del circuito de combustible)
Funciona en el mismo circuito de alta presión Common Rail. Al diagnosticar baja presión (P0087), verifique el caudal de la bomba antes de sustituir los inyectores.
Consejos de instalación
- [
- {
- "step": 1,
- "title": "Depressurize Fuel Rail & Remove Engine Cover",
- "instruction": "Depressurize fuel line using Toyota Techstream scan tool or fuel pump fuse removal. Remove engine beauty cover."
- },
- {
- "step": 2,
- "title": "Disconnect High-Pressure Delivery Pipe",
- "instruction": "Loosen steel fuel line union nuts (32 N·m). Detach direct injector wiring connectors and clamp retaining bolts (21 N·m)."
- },
- {
- "step": 3,
- "title": "Extract Injectors & Replace Teflon Seals",
- "instruction": "Carefully remove direct injectors from cylinder head ports. Install new Teflon seals using SST expander and sizing tool."
- },
- {
- "step": 4,
- "title": "Torque Retaining Bolts & Reconnect Steel Pipe",
- "instruction": "Press injectors firmly into head. Tighten rail clamp bolts to 21 N·m. Tighten high pressure pipe to 32 N·m. Verify zero leaks upon engine start."
- }
- ]
Codigos de Falla (DTC) y Protocolos de Diagnostico
Codigos de falla de diagnostico (DTC) comunes que se activan cuando este inyector common rail experimenta desgaste, fallas de circuito o desbalance:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Protocolos Técnicos de Diagnóstico y Servicio
Procedimientos de taller verificados, umbrales de prueba y pautas de servicio para este conjunto.