06J906036N
BOSCH 06J906036N Inyector Alta Presión VW Golf GTI Audi A4 1.8 2.0 TSI EA888 0261500160
06J906036, 0261500021, 0261500020, FJ1058, 06J906036G--150 barAplicaciones de vehículos y motores
| Vehículo | Motor | Años |
|---|---|---|
| Volkswagen Golf VI GTI 2.0 TSI | Volkswagen / Audi EA888 Gen 1 & Gen 2 (1.8L & 2.0L TSI / TFSI CCTA / CAEB / CDNC) | 2009-2013 |
| Audi A4 B8 2.0 TFSI | Volkswagen / Audi EA888 Gen 1 & Gen 2 (1.8L & 2.0L TSI / TFSI CCTA / CAEB / CDNC) | 2008-2015 |
| Audi Q5 8R 2.0 TFSI | Volkswagen / Audi EA888 Gen 1 & Gen 2 (1.8L & 2.0L TSI / TFSI CCTA / CAEB / CDNC) | 2009-2015 |
Especificaciones técnicas
| Especificación | Valor |
|---|---|
| part_number | 06J906036N |
| oem_reference | 06J906036N |
| manufacturer | BOSCH |
| system_type | Fuel Injector |
| pressure_rating | 150 bar (2175 psi) |
| operating_temperature | -40°C to +135°C |
| flange_mount_torque | 9 N-m (80 lb-in) |
| high_pressure_line_torque | 25 N-m (18 lb-ft) |
| diagnostic_dtc | P0300, P0301, P0171, P0172 |
| Presión de servicioDato clave |
Bomba de alta presión compatible (Ensamblaje del circuito de combustible)
Funciona en el mismo circuito de alta presión Common Rail. Al diagnosticar baja presión (P0087), verifique el caudal de la bomba antes de sustituir los inyectores.
Consejos de instalación
- Depressurize the fuel system completely via diagnostic scan tool or by removing the fuel pump fuse prior to line disassembly.
- Clean all surrounding bracket areas thoroughly using residue-free brake cleaner to prevent abrasive particulate ingress.
- Inspect the mechanical camshaft lobe and roller follower or clean injector bore seating surfaces before hardware alignment.
- Install component using fresh factory O-rings or Teflon combustion chamber seals lubricated only with clean motor oil.
- Torque mounting flange fasteners in alternating increments to 9 N-m (80 lb-in).
- Torque high-pressure hydraulic tube fittings using a calibrated flare nut wrench to 25 N-m (18 lb-ft).
- Prime low-pressure fuel circuit, cycle ignition key 3-4 times, and inspect for high-pressure hydraulic leaks before road test.
- Always replace single-use high-pressure metal fuel lines and micro-filter seals whenever disconnected.
- Verify camshaft driving lobe surfaces for scoring or flat spots before installing any mechanical pump.
- Reset long-term and short-term fuel trim adaptations via OBD-II diagnostic scanner after physical replacement.
Codigos de Falla (DTC) y Protocolos de Diagnostico
Codigos de falla de diagnostico (DTC) comunes que se activan cuando este inyector common rail experimenta desgaste, fallas de circuito o desbalance:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Protocolos Técnicos de Diagnóstico y Servicio
Procedimientos de taller verificados, umbrales de prueba y pautas de servicio para este conjunto.