23100-25010
DENSO 23100-25010 Pompe Haute Pression Toyota Camry RAV4 2.5L D-4S
23100-F0010, GDP512Integrated High-Speed Digital Flow Control Solenoid-200 barCompatibilité véhicules et motorisations
| Véhicule | Moteur | Années |
|---|---|---|
| Toyota Camry (XV70) | Toyota / Lexus 2.0L & 2.5L Dynamic Force D-4S (A25A-FKS / A25A-FXS / M20A-FKS) | 2018-2024 |
| Toyota RAV4 (XA50) | Toyota / Lexus 2.0L & 2.5L Dynamic Force D-4S (A25A-FKS / A25A-FXS / M20A-FKS) | 2019-2024 |
| Lexus ES 250 | Toyota / Lexus 2.0L & 2.5L Dynamic Force D-4S (A25A-FKS / A25A-FXS / M20A-FKS) | 2021-2024 |
Spécifications techniques
| Spécification | Valeur |
|---|---|
| Type de système | Toyota D-4S Dual Injection (Direct & Port) 200-bar System |
| Pression de serviceSpéc. clé | |
| Pump Mechanism | Camshaft Driven Single-Piston Plunger Mechanical Pump |
| Mounting Flange Bolt Torque | 21 N·m (15 lb-ft) flange bolts |
| Couple raccord tuyau haute pression | 30 N·m (22 lb-ft) high-pressure fuel pipe union nut |
| Drive Interface | Roller Lifter Tappet with Hardened Contact Face |
| Flow Control Solenoid | Integrated High-Speed Pulse-Width Modulated Solenoid Actuator |
| Manufacturer | Denso (Tier-1 OEM for Toyota Motor Corporation) |
| Denso Production Reference | 23100-25010 / GDP512 |
Pompe haute pression associée (Ensemble circuit de carburant)
Fonctionne sur le même circuit haute pression Common Rail. En cas de chute de pression (P0087), vérifier le débit de la pompe avant de remplacer les injecteurs.
Conseils de montage
- Never reuse high-pressure fuel pipes: Toyota mandates replacement of steel fuel delivery pipes whenever loosened to prevent fuel spray hazards.
- Inspect roller lifter bucket: A scored or worn roller tappet damages the camshaft drive lobe, necessitating expensive camshaft replacement.
- Verify engine oil for fuel dilution: A failing internal pump seal weeps fuel into the timing cover, causing oil level rise and bearing wear.
- Prime fuel circuit prior to cranking: Turn ignition ON for 5 seconds 3 times to prime low-pressure feed and purge air pockets.
Codes de Defaut (DTC) & Protocoles de Diagnostic
Codes de defaut diagnostiques (DTC) courants déclenchés lorsque cet injecteur common rail subit une usure, des pannes de circuit ou une dérive d'étalonnage:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Protocoles Techniques de Diagnostic & Réparation
Procédures d'atelier vérifiées, seuils de test et guides d'intervention pour cet ensemble.