23100-25010
DENSO 23100-25010 Yüksek Basınç Pompası Toyota Camry RAV4 2.5L D-4S
23100-F0010, GDP512Integrated High-Speed Digital Flow Control Solenoid-200 barUyumlu Araçlar ve Motorlar
| Araç | Motor | Model Yılları |
|---|---|---|
| Toyota Camry (XV70) | Toyota / Lexus 2.0L & 2.5L Dynamic Force D-4S (A25A-FKS / A25A-FXS / M20A-FKS) | 2018-2024 |
| Toyota RAV4 (XA50) | Toyota / Lexus 2.0L & 2.5L Dynamic Force D-4S (A25A-FKS / A25A-FXS / M20A-FKS) | 2019-2024 |
| Lexus ES 250 | Toyota / Lexus 2.0L & 2.5L Dynamic Force D-4S (A25A-FKS / A25A-FXS / M20A-FKS) | 2021-2024 |
Teknik Özellikler
| Özellik | Değer |
|---|---|
| Sistem Tipi | Toyota D-4S Dual Injection (Direct & Port) 200-bar System |
| Çalışma BasıncıTemel Değer | |
| Pump Mechanism | Camshaft Driven Single-Piston Plunger Mechanical Pump |
| Mounting Flange Bolt Torque | 21 N·m (15 lb-ft) flange bolts |
| FUEL LINE NUT TORQUE | 30 N·m (22 lb-ft) high-pressure fuel pipe union nut |
| Drive Interface | Roller Lifter Tappet with Hardened Contact Face |
| Flow Control Solenoid | Integrated High-Speed Pulse-Width Modulated Solenoid Actuator |
| Manufacturer | Denso (Tier-1 OEM for Toyota Motor Corporation) |
| Denso Production Reference | 23100-25010 / GDP512 |
Uyumlu Yüksek Basınç Pompası (Yakıt Devresi Grubu)
Aynı yüksek basınçlı Common Rail devresinde çalışır. Düşük basınç (P0087) teşhisinde enjektörleri değiştirmeden önce pompa debisini kontrol edin.
Montaj İpuçları
- Never reuse high-pressure fuel pipes: Toyota mandates replacement of steel fuel delivery pipes whenever loosened to prevent fuel spray hazards.
- Inspect roller lifter bucket: A scored or worn roller tappet damages the camshaft drive lobe, necessitating expensive camshaft replacement.
- Verify engine oil for fuel dilution: A failing internal pump seal weeps fuel into the timing cover, causing oil level rise and bearing wear.
- Prime fuel circuit prior to cranking: Turn ignition ON for 5 seconds 3 times to prime low-pressure feed and purge air pockets.
Ariza Kodlari (DTC) ve Teshis Protokolleri
Bu common rail enjektorunde asinma, devre arizasi veya kalibrasyon kaymasi olustugunda tetiklenen yaygin ariza kodlari (DTC):
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Teknik Arıza Teşhis ve Servis Protokolleri
Bu parça grubu için doğrulanmış atölye prosedürleri, test eşik değerleri ve servis talimatları.