JX6G-9F593-AA
BOSCH JX6G-9F593-AA Iniettore Alta Pressione Ford Focus Mk4 Fiesta ST 1.5T Dragon
JX6Z-9F593-A, 0261500824, 0261500595High-Pressure Multi-Hole Direct Solenoid Valve-250 barSpecifiche Tecniche
| Specifica | Valore |
|---|---|
| Tipo di sistema | Bosch HDEV5 250-bar High-Pressure Gasoline Direct Injector |
| Pressione di esercizioSpecifica Chiave | |
| Combustion Architecture | Optimized for 3-cylinder asymmetric firing order with selective cylinder deactivation |
| Fuel Rail Bolt Torque | 11 N·m (retaining clamp screws) |
| High Pressure Line Torque | 26 N·m (fuel delivery pipe flare connection) |
| Solenoid Coil Resistance | 1.6 - 2.0 Ω at 20°C (rapid pulse inductive circuit) |
| Codici guasto tipici | P0300 (Random Misfire), P0301-P0303 (Cylinder Misfire), P0171 (Fuel Trim System Lean) |
| Workshop Precaution | Do not reuse Teflon tip seals; ensure cylinder deactivation solenoid connectors are secured during harness routing |
Pompa alta pressione abbinata (Gruppo circuito carburante)
Funziona sullo stesso circuito ad alta pressione Common Rail. In caso di bassa pressione rail (P0087), verificare la portata della pompa prima di sostituire gli iniettori.
Istruzioni di montaggio
- [
- {
- "step": 1,
- "title": "Relieve Fuel Pressure & Disconnect 12V Battery Ground",
- "instruction": "Depressurize fuel rail via scan tool command or fuel pump inertia switch cutout. Disconnect battery negative ground post before servicing."
- },
- {
- "step": 2,
- "title": "Remove Air Ducting, Harness Plugs & Fuel Rail Fasteners",
- "instruction": "Disconnect charge air hoses over cylinder head. Unclip electrical harness connections from direct injectors. Loosen fuel rail retaining fasteners (11 N·m)."
- },
- {
- "step": 3,
- "title": "Withdraw Direct Injectors & Fit Fresh Teflon Tip Seals",
- "instruction": "Extract direct injectors using slide puller adapter. Inspect nozzle tip micro-orifices. Install fresh Teflon combustion seal ring and reshape using resizing tool."
- },
- {
- "step": 4,
- "title": "Torque Fuel Rail Bolts & High Pressure Fuel Unions",
- "instruction": "Position injectors into cylinder head ports. Tighten rail hold-down bolts to 11 N·m. Torque high pressure fuel pipe nut to 26 N·m. Start engine and verify zero leakage."
- }
- ]
Codici Guasto (DTC) e Protocolli Diagnostici
Codici guasto diagnostici (DTC) comuni generati quando questo iniettore common rail presenta usura, problemi ai circuiti o scostamenti:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Protocolli Tecnici di Diagnosi & Assistenza
Procedure d'officina verificate, valori soglia di test e linee guida operative per questo assieme.