JX6G-9F593-AA
BOSCH JX6G-9F593-AA Yüksek Basınç Enjektörü Ford Focus Mk4 Fiesta ST 1.5T Dragon
JX6Z-9F593-A, 0261500824, 0261500595High-Pressure Multi-Hole Direct Solenoid Valve-250 barTeknik Özellikler
| Özellik | Değer |
|---|---|
| Sistem Tipi | Bosch HDEV5 250-bar High-Pressure Gasoline Direct Injector |
| Çalışma BasıncıTemel Değer | |
| Combustion Architecture | Optimized for 3-cylinder asymmetric firing order with selective cylinder deactivation |
| Fuel Rail Bolt Torque | 11 N·m (retaining clamp screws) |
| High Pressure Line Torque | 26 N·m (fuel delivery pipe flare connection) |
| Solenoid Coil Resistance | 1.6 - 2.0 Ω at 20°C (rapid pulse inductive circuit) |
| Tipik Arıza Kodları | P0300 (Random Misfire), P0301-P0303 (Cylinder Misfire), P0171 (Fuel Trim System Lean) |
| Workshop Precaution | Do not reuse Teflon tip seals; ensure cylinder deactivation solenoid connectors are secured during harness routing |
Uyumlu Yüksek Basınç Pompası (Yakıt Devresi Grubu)
Aynı yüksek basınçlı Common Rail devresinde çalışır. Düşük basınç (P0087) teşhisinde enjektörleri değiştirmeden önce pompa debisini kontrol edin.
Montaj İpuçları
- [
- {
- "step": 1,
- "title": "Relieve Fuel Pressure & Disconnect 12V Battery Ground",
- "instruction": "Depressurize fuel rail via scan tool command or fuel pump inertia switch cutout. Disconnect battery negative ground post before servicing."
- },
- {
- "step": 2,
- "title": "Remove Air Ducting, Harness Plugs & Fuel Rail Fasteners",
- "instruction": "Disconnect charge air hoses over cylinder head. Unclip electrical harness connections from direct injectors. Loosen fuel rail retaining fasteners (11 N·m)."
- },
- {
- "step": 3,
- "title": "Withdraw Direct Injectors & Fit Fresh Teflon Tip Seals",
- "instruction": "Extract direct injectors using slide puller adapter. Inspect nozzle tip micro-orifices. Install fresh Teflon combustion seal ring and reshape using resizing tool."
- },
- {
- "step": 4,
- "title": "Torque Fuel Rail Bolts & High Pressure Fuel Unions",
- "instruction": "Position injectors into cylinder head ports. Tighten rail hold-down bolts to 11 N·m. Torque high pressure fuel pipe nut to 26 N·m. Start engine and verify zero leakage."
- }
- ]
Ariza Kodlari (DTC) ve Teshis Protokolleri
Bu common rail enjektorunde asinma, devre arizasi veya kalibrasyon kaymasi olustugunda tetiklenen yaygin ariza kodlari (DTC):
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Teknik Arıza Teşhis ve Servis Protokolleri
Bu parça grubu için doğrulanmış atölye prosedürleri, test eşik değerleri ve servis talimatları.