35320-2G700
HYUNDAI 35320-2G700 Pompa Alta Pressione Sonata Optima 2.0T 2.4L GDI
35320-2G720, 35320-2G730, GDP206, HM10014Integrated High-Speed Pulse-Width Modulated Metering Valve-150 barSpecifiche Tecniche
| Specifica | Valore |
|---|---|
| Tipo di sistema | Hyundai-Kia Theta II GDI 150-bar High-Pressure Fuel System |
| Pressione di esercizioSpecifica Chiave | |
| Pump Mechanism | Exhaust Camshaft Lobe Actuated Single-Piston Plunger Pump |
| Mounting Flange Bolt Torque | 13 N·m (115 in-lb) flange bolts |
| FUEL LINE NUT TORQUE | 28 N·m (21 lb-ft) high-pressure delivery pipe flare nut |
| Drive Interface | Roller Tappet Bucket with Hardened Contact Face |
| Low-Pressure Inlet Fitting | Quick-Disconnect Barb with Integrated Damper |
| Manufacturer | Hyundai Mobis / Kefico (Tier-1 OEM for Hyundai Motor Group) |
| OEM Service Reference | 35320-2G700 / 35320-2G740 |
Pompa alta pressione abbinata (Gruppo circuito carburante)
Funziona sullo stesso circuito ad alta pressione Common Rail. In caso di bassa pressione rail (P0087), verificare la portata della pompa prima di sostituire gli iniettori.
Istruzioni di montaggio
- [
- {
- "step": 1,
- "title": "Low-Pressure Supply Bleed & Battery Disconnect",
- "instruction": "Remove fuel pump fuse from underhood junction box. Crank engine for 5 seconds to depressurize fuel lines. Disconnect vehicle negative 12V battery terminal."
- },
- {
- "step": 2,
- "title": "Engine Beauty Cover & Noise Damper Removal",
- "instruction": "Unbolt engine cover and pull back the heavy rubber noise shield covering the high-pressure fuel pump on top of the valve cover."
- },
- {
- "step": 3,
- "title": "High-Pressure Pipe & Harness Disconnection",
- "instruction": "Unplug electrical solenoid harness. Use a 17mm line wrench with counter-torque to disconnect high-pressure metal fuel pipe from pump outlet."
- },
- {
- "step": 4,
- "title": "Pump Removal & Roller Lifter Tappet Check",
- "instruction": "Loosen mounting bolts alternately in half-turn increments. Lift pump out and remove the roller tappet. Inspect tappet face and camshaft lobe for wear grooves."
- },
- {
- "step": 5,
- "title": "New Pump Installation & Torque Sequence",
- "instruction": "Lubricate new Viton O-ring and roller tappet with fresh oil. Rotate engine to lowest cam profile. Torque mounting bolts to 13 N·m (115 in-lb) and fuel pipe union nut to 28 N·m (21 lb-ft)."
- }
- ]
Codici Guasto (DTC) e Protocolli Diagnostici
Codici guasto diagnostici (DTC) comuni generati quando questo iniettore common rail presenta usura, problemi ai circuiti o scostamenti:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Protocolli Tecnici di Diagnosi & Assistenza
Procedure d'officina verificate, valori soglia di test e linee guida operative per questo assieme.