35320-2G720
BOSCH 35320-2G720 Pompă Înaltă Presiune Hyundai Sonata Kia Optima 2.4L GDI Theta II
35320-2G730, 35320-2G700, 0261520282Integrated Normally Open 12V Pulse-Width Modulated SCV-150 barCompatibilitate vehicule și motoare
| Vehicul | Motor | Ani fabricație |
|---|---|---|
| Hyundai Sonata 2.4L GDI | Hyundai / Kia 2.0L T-GDI & 2.4L GDI Theta II (G4KH / G4KJ) | 2011-2019 |
| Kia Optima K5 2.4L GDI | Hyundai / Kia 2.0L T-GDI & 2.4L GDI Theta II (G4KH / G4KJ) | 2011-2020 |
| Hyundai Santa Fe Sport 2.4L GDI | Hyundai / Kia 2.0L T-GDI & 2.4L GDI Theta II (G4KH / G4KJ) | 2013-2018 |
Specificații tehnice
| Specificație | Valoare |
|---|---|
| Tip sistem | Bosch HDP-5 Radial Mechanical Plunger High-Pressure Fuel Pump |
| Presiune de lucruSpecificație de bază | |
| Actuation Mechanism | Exhaust Camshaft Lobe via Roller Tappet Lifter 35325-2G700 |
| Mounting Flange Torque | 13 N·m Evenly tightened cross pattern |
| High Pressure Line Torque | 27 N·m Flare Nut Connection |
| Pressure Regulator Valve | Integrated Normally Open 12V Pulse-Width Modulated SCV |
| Coduri de eroare frecvente | P0087 (Fuel Rail Pressure Too Low), P0088 (Rail Pressure Too High), P0172 (Fuel Trim Rich) |
| Workshop Precaution | Inspect cam roller follower 35325-2G700 for scoring; verify oil is not fuel-diluted from torn plunger seal |
Injectoare de combustibil compatibile (Ansamblu circuit combustibil)
Alimentat direct de această pompă de înaltă presiune. Verificați returul pe injectoare dacă presiunea în rampă nu crește la pornire.
Instrucțiuni de montaj
- [
- {
- "step": 1,
- "title": "Depressurize Fuel Rail & Disconnect Wiring",
- "instruction": "Depressurize fuel line by removing fuel pump fuse. Disconnect electrical connector from high pressure flow control solenoid."
- },
- {
- "step": 2,
- "title": "Disconnect Fuel Feed & High Pressure Pipes",
- "instruction": "Remove low pressure rubber supply line clamp. Loosen high-pressure flared fuel pipe connection (27 N·m union nut)."
- },
- {
- "step": 3,
- "title": "Remove Flange Bolts & Inspect Roller Tappet",
- "instruction": "Back out mounting flange bolts evenly in alternating turns. Remove pump body and extract roller lifter 35325-2G700. Check for surface galling."
- },
- {
- "step": 4,
- "title": "Install Pump with New O-Ring & Final Torque",
- "instruction": "Install new lubricated Viton seal ring. Position pump squarely and torque flange bolts evenly to 13 N·m. Torque high pressure steel pipe to 27 N·m."
- }
- ]
Coduri de Eroare (DTC) si Protocoale de Diagnostic
Coduri comune de eroare de diagnosticare (DTC) declansate atunci cand acest injector common rail sufera uzura, defectiuni de circuit sau abateri:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Protocoale Tehnice de Diagnosticare & Service
Proceduri verificate de atelier, praguri de testare și standarde de intervenție pentru acest ansamblu.