35320-2G720
BOSCH 35320-2G720 Pompe Haute Pression Hyundai Sonata Kia Optima 2.4L GDI Theta II
35320-2G730, 35320-2G700, 0261520282Integrated Normally Open 12V Pulse-Width Modulated SCV-150 barCompatibilité véhicules et motorisations
Spécifications techniques
| Spécification | Valeur |
|---|---|
| Type de système | Bosch HDP-5 Radial Mechanical Plunger High-Pressure Fuel Pump |
| Pression de serviceSpéc. clé | |
| Actuation Mechanism | Exhaust Camshaft Lobe via Roller Tappet Lifter 35325-2G700 |
| Mounting Flange Torque | 13 N·m Evenly tightened cross pattern |
| High Pressure Line Torque | 27 N·m Flare Nut Connection |
| Pressure Regulator Valve | Integrated Normally Open 12V Pulse-Width Modulated SCV |
| Codes défauts fréquents | P0087 (Fuel Rail Pressure Too Low), P0088 (Rail Pressure Too High), P0172 (Fuel Trim Rich) |
| Workshop Precaution | Inspect cam roller follower 35325-2G700 for scoring; verify oil is not fuel-diluted from torn plunger seal |
Injecteurs de carburant associés (Ensemble circuit de carburant)
Alimenté directement par cette pompe haute pression. Vérifier le débit de retour des injecteurs si la pression de rail ne monte pas au démarrage.
Conseils de montage
- [
- {
- "step": 1,
- "title": "Depressurize Fuel Rail & Disconnect Wiring",
- "instruction": "Depressurize fuel line by removing fuel pump fuse. Disconnect electrical connector from high pressure flow control solenoid."
- },
- {
- "step": 2,
- "title": "Disconnect Fuel Feed & High Pressure Pipes",
- "instruction": "Remove low pressure rubber supply line clamp. Loosen high-pressure flared fuel pipe connection (27 N·m union nut)."
- },
- {
- "step": 3,
- "title": "Remove Flange Bolts & Inspect Roller Tappet",
- "instruction": "Back out mounting flange bolts evenly in alternating turns. Remove pump body and extract roller lifter 35325-2G700. Check for surface galling."
- },
- {
- "step": 4,
- "title": "Install Pump with New O-Ring & Final Torque",
- "instruction": "Install new lubricated Viton seal ring. Position pump squarely and torque flange bolts evenly to 13 N·m. Torque high pressure steel pipe to 27 N·m."
- }
- ]
Codes de Defaut (DTC) & Protocoles de Diagnostic
Codes de defaut diagnostiques (DTC) courants déclenchés lorsque cet injecteur common rail subit une usure, des pannes de circuit ou une dérive d'étalonnage:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Protocoles Techniques de Diagnostic & Réparation
Procédures d'atelier vérifiées, seuils de test et guides d'intervention pour cet ensemble.