06L906036K
CONTINENTAL 06L906036K Форсунка MPI VW Audi EA888 Gen 3B 2.0 TSI
06L906036D, 06L906036J, 06L906036L, A2C9127710012-Hole Wide-Angle Atomization Port Injector Valve12-Hole Precision Multi-Hole Spray Diffuser5.0 barПрименяемость к авто и двигателям
| Автомобиль | Двигатель | Годы выпуска |
|---|---|---|
| Volkswagen Golf GTI MK7.5 | Volkswagen / Audi EA888 Gen 3 & Gen 3B (1.8L & 2.0L TSI / TFSI CHHB / CJXC / CYFB) | 2018-2024 |
| Audi A4 B9 2.0 TFSI | Volkswagen / Audi EA888 Gen 3 & Gen 3B (1.8L & 2.0L TSI / TFSI CHHB / CJXC / CYFB) | 2016-2023 |
| Audi Q5 FY 2.0 TFSI | Volkswagen / Audi EA888 Gen 3 & Gen 3B (1.8L & 2.0L TSI / TFSI CHHB / CJXC / CYFB) | 2018-2024 |
Технические характеристики
| Параметр | Значение |
|---|---|
| Injector Type | Continental Multi-Point Port Fuel Injector (MPI) |
| Operating Manifold Pressure | 4.0 to 7.0 bar (58 to 101 psi) |
| Nozzle Atomization Hole PatternОсн. параметр | |
| Coil Resistance Value | 12.0 to 14.5 Ohms at 20°C (High Impedance) |
| Manifold Rail Bolt Torque | 9 N·m (Even progressive pass) |
| Tightening Torque | 9 N·m |
| Момент затяжки прижимной скобы | 9 N·m |
| Primary OEM Reference | 06L906036K, 06L906036D, 06L906036J, 06L906036L |
| Engine Emission Compliance | Euro 6d / WLTP / LEV III Tier 3 |
| Standard Industrial Warranty | 12 Months / Unlimited Mileage |
| Рабочее давлениеОсн. параметр |
Совместимый ТНВД (Топливный контур в сборе)
Работает в одном контуре Common Rail высокого давления. При падении давления (P0087) проверьте подачу насоса перед заменой форсунок.
Рекомендации по установке
Необходимый инструмент: Torx T30 socket and 1/4-inch drive torque wrench for fuel rail bolts, O-ring pick for old seal removal, Silicone O-ring assembly grease (dielectric or clean mineral oil), Clean lint-free shop cloths for intake port protection
- Disconnect vehicle battery negative terminal; relieve low-pressure line pressure via Schrader service valve or fuel pump fuse removal.
- Disconnect electrical wiring harness connectors from all 4 port fuel injectors.
- Remove the two T30 Torx mounting fasteners securing the composite port fuel rail to the intake manifold.
- Gently rock the fuel rail assembly backward to pull all 4 injectors evenly from their manifold port sockets.
- Remove retaining clips holding injectors to the fuel rail; pull injectors from rail cups.
- Clean fuel rail cups and manifold injector ports with lint-free wipes; inspect for debris.
- Fit brand new upper and lower Viton O-rings onto each new injector; lubricate O-rings lightly with clean silicone grease.
- Insert injectors into fuel rail cups ensuring correct alignment tab orientation; reinstall metal retaining clips securely.
- Seat the complete injector rail assembly squarely into the intake manifold sockets until fully seated.
- Install T30 rail mounting bolts and torque evenly to 9 N·m.
- Reconnect injector wiring harness connectors until locking tabs click.
- Turn ignition on for 10 seconds without cranking to pressurize low-pressure fuel rail; inspect all 4 injector seats for leaks.
- O-Ring Lubrication Mandate: Never install Viton O-rings dry; dry assembly will pinch or tear the rubber seal, causing dangerous pressurized fuel leaks on the intake manifold.
- Retaining Clip Inspection: Ensure injector metal retaining clips snap fully into the rail grooves to prevent injector push-out under fuel pulse pressure.
Часто задаваемые вопросы
What are the primary symptoms when 06L906036K fails?
Primary symptoms include extended cold engine cranking, severe hesitation under wide-open throttle, rough idle RPM fluctuation, and Diagnostic Trouble Codes P0087 (Fuel Rail/System Pressure Too Low), P0089 (Fuel Pressure Regulator Performance), or P0300 (Random/Multiple Cylinder Misfire).
What is the exact tightening torque for 06L906036K?
The holding flange mounting torque is 9 N·m, and the high-pressure fuel pipe union nut must be torqued to 9 N·m.
Can I reuse the seals when replacing 06L906036K?
No. All high-pressure fuel seals, including Viton O-rings and combustion chamber Teflon rings, are strictly single-use. Reusing compressed seals will cause pressurized fuel leaks or combustion blowby into the cylinder head.
Коды неисправностей (DTC) и протоколы диагностики
Основные диагностические коды неисправностей (DTC), возникающие при износе, замыкании цепи или отклонении калибровки данной форсунки Common Rail:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Технические протоколы диагностики и обслуживания
Проверенные сервисные процедуры, пороговые значения тестов и регламенты для данного узла.