06L906036K
CONTINENTAL 06L906036K بخاخ منفذ حقن MPI فولكس فاجن أودي 2.0 TSI
06L906036D, 06L906036J, 06L906036L, A2C9127710012-Hole Wide-Angle Atomization Port Injector Valve12-Hole Precision Multi-Hole Spray Diffuser5.0 barتوافق المركبات والمحركات
| المركبة | المحرك | سنوات الصنع |
|---|---|---|
| Volkswagen Golf GTI MK7.5 | Volkswagen / Audi EA888 Gen 3 & Gen 3B (1.8L & 2.0L TSI / TFSI CHHB / CJXC / CYFB) | 2018-2024 |
| Audi A4 B9 2.0 TFSI | Volkswagen / Audi EA888 Gen 3 & Gen 3B (1.8L & 2.0L TSI / TFSI CHHB / CJXC / CYFB) | 2016-2023 |
| Audi Q5 FY 2.0 TFSI | Volkswagen / Audi EA888 Gen 3 & Gen 3B (1.8L & 2.0L TSI / TFSI CHHB / CJXC / CYFB) | 2018-2024 |
المواصفات الفنية
| المواصفة | القيمة |
|---|---|
| Injector Type | Continental Multi-Point Port Fuel Injector (MPI) |
| Operating Manifold Pressure | 4.0 to 7.0 bar (58 to 101 psi) |
| Nozzle Atomization Hole Patternمواصفة أساسية | |
| Coil Resistance Value | 12.0 to 14.5 Ohms at 20°C (High Impedance) |
| Manifold Rail Bolt Torque | 9 N·m (Even progressive pass) |
| Tightening Torque | 9 N·m |
| عزم ربط مشبك التثبيت | 9 N·m |
| Primary OEM Reference | 06L906036K, 06L906036D, 06L906036J, 06L906036L |
| Engine Emission Compliance | Euro 6d / WLTP / LEV III Tier 3 |
| Standard Industrial Warranty | 12 Months / Unlimited Mileage |
| ضغط التشغيلمواصفة أساسية |
مضخة وقود الضغط العالي المتوافقة (مجموعة دائرة الوقود)
تعمل على نفس دائرة الضغط العالي بنظام القضيب المشترك. عند تشخيص انخفاض الضغط (P0087)، تحقق من تدفق المضخة قبل استبدال الحاقنات.
إرشادات التركيب
العدد والأدوات المطلوبة: Torx T30 socket and 1/4-inch drive torque wrench for fuel rail bolts, O-ring pick for old seal removal, Silicone O-ring assembly grease (dielectric or clean mineral oil), Clean lint-free shop cloths for intake port protection
- Disconnect vehicle battery negative terminal; relieve low-pressure line pressure via Schrader service valve or fuel pump fuse removal.
- Disconnect electrical wiring harness connectors from all 4 port fuel injectors.
- Remove the two T30 Torx mounting fasteners securing the composite port fuel rail to the intake manifold.
- Gently rock the fuel rail assembly backward to pull all 4 injectors evenly from their manifold port sockets.
- Remove retaining clips holding injectors to the fuel rail; pull injectors from rail cups.
- Clean fuel rail cups and manifold injector ports with lint-free wipes; inspect for debris.
- Fit brand new upper and lower Viton O-rings onto each new injector; lubricate O-rings lightly with clean silicone grease.
- Insert injectors into fuel rail cups ensuring correct alignment tab orientation; reinstall metal retaining clips securely.
- Seat the complete injector rail assembly squarely into the intake manifold sockets until fully seated.
- Install T30 rail mounting bolts and torque evenly to 9 N·m.
- Reconnect injector wiring harness connectors until locking tabs click.
- Turn ignition on for 10 seconds without cranking to pressurize low-pressure fuel rail; inspect all 4 injector seats for leaks.
- O-Ring Lubrication Mandate: Never install Viton O-rings dry; dry assembly will pinch or tear the rubber seal, causing dangerous pressurized fuel leaks on the intake manifold.
- Retaining Clip Inspection: Ensure injector metal retaining clips snap fully into the rail grooves to prevent injector push-out under fuel pulse pressure.
الأسئلة الشائعة
What are the primary symptoms when 06L906036K fails?
Primary symptoms include extended cold engine cranking, severe hesitation under wide-open throttle, rough idle RPM fluctuation, and Diagnostic Trouble Codes P0087 (Fuel Rail/System Pressure Too Low), P0089 (Fuel Pressure Regulator Performance), or P0300 (Random/Multiple Cylinder Misfire).
What is the exact tightening torque for 06L906036K?
The holding flange mounting torque is 9 N·m, and the high-pressure fuel pipe union nut must be torqued to 9 N·m.
Can I reuse the seals when replacing 06L906036K?
No. All high-pressure fuel seals, including Viton O-rings and combustion chamber Teflon rings, are strictly single-use. Reusing compressed seals will cause pressurized fuel leaks or combustion blowby into the cylinder head.
رموز الاعطال التشخيصية (DTC) وبروتوكولات الفحص
رموز اعطال التشخيص الشائعة (DTC) التي يتم تسجيلها عند تآكل حاقن الديزل أو حدوث خلل كهربائي:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
بروتوكولات التشخيص والخدمة الفنية
إجراءات ورشة العمل المعتمدة، وحدود الاختبار التشخيصية، ومعايير الخدمة لهذا المكون.