06L906036K
CONTINENTAL 06L906036K Emme Port Enjektörü VW Audi EA888 Gen 3B 2.0 TSI
06L906036D, 06L906036J, 06L906036L, A2C9127710012-Hole Wide-Angle Atomization Port Injector Valve12-Hole Precision Multi-Hole Spray Diffuser5.0 barUyumlu Araçlar ve Motorlar
| Araç | Motor | Model Yılları |
|---|---|---|
| Volkswagen Golf GTI MK7.5 | Volkswagen / Audi EA888 Gen 3 & Gen 3B (1.8L & 2.0L TSI / TFSI CHHB / CJXC / CYFB) | 2018-2024 |
| Audi A4 B9 2.0 TFSI | Volkswagen / Audi EA888 Gen 3 & Gen 3B (1.8L & 2.0L TSI / TFSI CHHB / CJXC / CYFB) | 2016-2023 |
| Audi Q5 FY 2.0 TFSI | Volkswagen / Audi EA888 Gen 3 & Gen 3B (1.8L & 2.0L TSI / TFSI CHHB / CJXC / CYFB) | 2018-2024 |
Teknik Özellikler
| Özellik | Değer |
|---|---|
| Injector Type | Continental Multi-Point Port Fuel Injector (MPI) |
| Operating Manifold Pressure | 4.0 to 7.0 bar (58 to 101 psi) |
| Nozzle Atomization Hole PatternTemel Değer | |
| Coil Resistance Value | 12.0 to 14.5 Ohms at 20°C (High Impedance) |
| Manifold Rail Bolt Torque | 9 N·m (Even progressive pass) |
| Tightening Torque | 9 N·m |
| Enjektör Baskı Çatalı Torku | 9 N·m |
| Primary OEM Reference | 06L906036K, 06L906036D, 06L906036J, 06L906036L |
| Engine Emission Compliance | Euro 6d / WLTP / LEV III Tier 3 |
| Standard Industrial Warranty | 12 Months / Unlimited Mileage |
| Çalışma BasıncıTemel Değer |
Uyumlu Yüksek Basınç Pompası (Yakıt Devresi Grubu)
Aynı yüksek basınçlı Common Rail devresinde çalışır. Düşük basınç (P0087) teşhisinde enjektörleri değiştirmeden önce pompa debisini kontrol edin.
Montaj İpuçları
Gerekli ekipmanlar: Torx T30 socket and 1/4-inch drive torque wrench for fuel rail bolts, O-ring pick for old seal removal, Silicone O-ring assembly grease (dielectric or clean mineral oil), Clean lint-free shop cloths for intake port protection
- Disconnect vehicle battery negative terminal; relieve low-pressure line pressure via Schrader service valve or fuel pump fuse removal.
- Disconnect electrical wiring harness connectors from all 4 port fuel injectors.
- Remove the two T30 Torx mounting fasteners securing the composite port fuel rail to the intake manifold.
- Gently rock the fuel rail assembly backward to pull all 4 injectors evenly from their manifold port sockets.
- Remove retaining clips holding injectors to the fuel rail; pull injectors from rail cups.
- Clean fuel rail cups and manifold injector ports with lint-free wipes; inspect for debris.
- Fit brand new upper and lower Viton O-rings onto each new injector; lubricate O-rings lightly with clean silicone grease.
- Insert injectors into fuel rail cups ensuring correct alignment tab orientation; reinstall metal retaining clips securely.
- Seat the complete injector rail assembly squarely into the intake manifold sockets until fully seated.
- Install T30 rail mounting bolts and torque evenly to 9 N·m.
- Reconnect injector wiring harness connectors until locking tabs click.
- Turn ignition on for 10 seconds without cranking to pressurize low-pressure fuel rail; inspect all 4 injector seats for leaks.
- O-Ring Lubrication Mandate: Never install Viton O-rings dry; dry assembly will pinch or tear the rubber seal, causing dangerous pressurized fuel leaks on the intake manifold.
- Retaining Clip Inspection: Ensure injector metal retaining clips snap fully into the rail grooves to prevent injector push-out under fuel pulse pressure.
Sıkça Sorulan Sorular
What are the primary symptoms when 06L906036K fails?
Primary symptoms include extended cold engine cranking, severe hesitation under wide-open throttle, rough idle RPM fluctuation, and Diagnostic Trouble Codes P0087 (Fuel Rail/System Pressure Too Low), P0089 (Fuel Pressure Regulator Performance), or P0300 (Random/Multiple Cylinder Misfire).
What is the exact tightening torque for 06L906036K?
The holding flange mounting torque is 9 N·m, and the high-pressure fuel pipe union nut must be torqued to 9 N·m.
Can I reuse the seals when replacing 06L906036K?
No. All high-pressure fuel seals, including Viton O-rings and combustion chamber Teflon rings, are strictly single-use. Reusing compressed seals will cause pressurized fuel leaks or combustion blowby into the cylinder head.
Ariza Kodlari (DTC) ve Teshis Protokolleri
Bu common rail enjektorunde asinma, devre arizasi veya kalibrasyon kaymasi olustugunda tetiklenen yaygin ariza kodlari (DTC):
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Teknik Arıza Teşhis ve Servis Protokolleri
Bu parça grubu için doğrulanmış atölye prosedürleri, test eşik değerleri ve servis talimatları.