23101-25010
DENSO 23101-25010 Högtryckspump Toyota Camry RAV4 2.5L A25A-FKS 299000-0021
23100-25011, GDP512, HM10052--200 barPassande fordon & motorer
| Fordon | Motor | Årsmodell |
|---|---|---|
| Toyota Camry (XV70) | Toyota / Lexus 2.0L & 2.5L Dynamic Force D-4S (A25A-FKS / A25A-FXS / M20A-FKS) | 2018-2024 |
| Toyota RAV4 (XA50) | Toyota / Lexus 2.0L & 2.5L Dynamic Force D-4S (A25A-FKS / A25A-FXS / M20A-FKS) | 2019-2024 |
| Lexus ES 250 | Toyota / Lexus 2.0L & 2.5L Dynamic Force D-4S (A25A-FKS / A25A-FXS / M20A-FKS) | 2021-2024 |
Tekniska specifikationer
| Specifikation | Värde |
|---|---|
| part_number | 23101-25010 |
| oem_reference | 23101-25010 |
| manufacturer | DENSO |
| system_type | High Pressure Fuel Pump |
| pressure_rating | 200 bar (2900 psi) |
| operating_temperature | -40°C to +135°C |
| flange_mount_torque | 21 N-m (15 lb-ft) |
| high_pressure_line_torque | 30 N-m (22 lb-ft) |
| diagnostic_dtc | P0087, P0088, P0171, P0172 |
| ArbetstryckHuvudspec. |
Matchande bränsleinjektorer (Bränslekretsmontering)
Matas direkt från denna högtryckspump. Kontrollera returflödet om railtrycket inte byggs upp vid start.
Monteringsanvisningar
- Depressurize the fuel system completely via diagnostic scan tool or by removing the fuel pump fuse prior to line disassembly.
- Clean all surrounding bracket areas thoroughly using residue-free brake cleaner to prevent abrasive particulate ingress.
- Inspect the mechanical camshaft lobe and roller follower or clean injector bore seating surfaces before hardware alignment.
- Install component using fresh factory O-rings or Teflon combustion chamber seals lubricated only with clean motor oil.
- Torque mounting flange fasteners in alternating increments to 21 N-m (15 lb-ft).
- Torque high-pressure hydraulic tube fittings using a calibrated flare nut wrench to 30 N-m (22 lb-ft).
- Prime low-pressure fuel circuit, cycle ignition key 3-4 times, and inspect for high-pressure hydraulic leaks before road test.
- Always replace single-use high-pressure metal fuel lines and micro-filter seals whenever disconnected.
- Verify camshaft driving lobe surfaces for scoring or flat spots before installing any mechanical pump.
- Reset long-term and short-term fuel trim adaptations via OBD-II diagnostic scanner after physical replacement.
Felkoder (DTC) och Diagnosprotokoll
Vanliga diagnosfelkoder (DTC) som aktiveras nar denna common rail-injektor uppvisar slitage, kretsfel eller kalibreringsavvikelse:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Tekniska Diagnos- och Serviceprotokoll
Verifierade verkstadsrutiner, testgränsvärden och serviceinstruktioner för denna komponent.