0261500055
BOSCH 0261500055 Direkt Enjektör VW Audi 2.0 TFSI EA113 Golf R
06F906036A, 06F906036F, 06F906036GPrecision Solenoid Armature with Multi-Hole Atomizer Nozzle-130 barÜrüne Genel Bakış
The Bosch 0261500055 (VW/Audi OE 06F906036F / 06F906036G) is the genuine original equipment high-flow direct fuel injector for VAG 2.0 TFSI EA113 performance engines equipped with BorgWarner K04 turbochargers. Standard factory equipment on the Volkswagen Golf R (MK6), Audi S3 (8P), Audi TTS, and SEAT Leon Cupra R, this multi-hole solenoid injector delivers high-pressure atomization up to 130 bar. Typical failure symptoms include cold-start stumbling, black smoke on kickdown, and cylinder misfire codes P0300 through P0304.
COLD START CYLINDER WASH & INJECTOR TIP WEEPING: On performance EA113 2.0 TFSI engines (Golf R, S3, Cupra R), direct fuel injectors operate under continuous 130 bar rail pressure. Varnish buildup causes the injector needle to stick weeping open overnight. This floods the combustion chamber with raw gasoline, washing cylinder bore oil (Cylinder Wash), causing violent morning cold misfires (P0300, P0301), and damaging the catalytic converter. Always install a fresh Teflon combustion seal ring using a cone installation tool.
Uyumlu Araçlar ve Motorlar
| Araç | Motor | Model Yılları |
|---|---|---|
| Volkswagen Golf R MK6 | Volkswagen / Audi EA113 2.0L TFSI (BPY / AXX / BWA / CDL) | 2010-2013 |
| Audi S3 8P | Volkswagen / Audi EA113 2.0L TFSI (BPY / AXX / BWA / CDL) | 2006-2012 |
| Audi TTS 8J | Volkswagen / Audi EA113 2.0L TFSI (BPY / AXX / BWA / CDL) | 2008-2014 |
Teknik Özellikler
| Özellik | Değer |
|---|---|
| Injector Generation | Bosch HDEV-1 High-Pressure Gasoline Direct Injector |
| Operating Rail PressureTemel Değer | |
| Spray Pattern | High-Flow Multi-Hole Precision Atomizer Nozzle |
| Coil Resistance | 1.40 to 1.80 Ohms at 20°C |
| Combustion Seal Type | Combustion Chamber Virgin Teflon (PTFE) Ring |
| Special Assembly Tool | VW/Audi T10133 Teflon Seal Expanding Cone & Sizing Sleeve |
| Fuel Rail Hold Down Torque | 10 N·m (Even cross-pattern) |
| Tightening Torque | 10 N·m |
| Enjektör Baskı Çatalı Torku | 10 N·m |
| Primary OEM Reference | 06F906036A, 06F906036F, 06F906036G |
| Engine Emission Compliance | Euro 5 / Tier 2 Bin 5 |
| Standard Industrial Warranty | 12 Months / Unlimited Mileage |
| Çalışma BasıncıTemel Değer |
Uyumlu Yüksek Basınç Pompası (Yakıt Devresi Grubu)
Aynı yüksek basınçlı Common Rail devresinde çalışır. Düşük basınç (P0087) teşhisinde enjektörleri değiştirmeden önce pompa debisini kontrol edin.
Montaj İpuçları
Gerekli ekipmanlar: VW/Audi T10133 Teflon seal installation guide cone and sizing sleeves, Slide hammer injector removal adapter T10133/1, Torque wrench calibrated for 8-15 N·m, Brass bore cleaning brush and lint-free cotton swabs, Clean engine oil or assembly lube for Viton rail O-rings
- Disconnect battery negative terminal; relieve low-pressure fuel circuit pressure before intake disassembly.
- Remove intake manifold to gain full access to high-pressure fuel rail and cylinder head injector ports.
- Disconnect electrical wiring harness connectors from all four GDI injectors.
- Remove fuel rail retaining bolts; extract fuel rail assembly evenly to prevent cocking injectors.
- Attach slide hammer puller T10133/1 to injector body; extract injector straight out of cylinder head bore.
- Clean carbon soot from injector cylinder head bore using brass brush and vacuum; never use steel tools.
- Remove old Teflon seal; expand new virgin Teflon ring over guide cone into injector seal groove.
- Slide sizing sleeve over Teflon ring and allow 5 minutes for Teflon memory recovery to shrink seal to diameter.
- Lubricate Viton upper O-ring with clean motor oil; insert injector into cylinder head bore by hand pressure.
- Reinstall fuel rail assembly; torque rail hold-down bolts evenly in stages to 10 N·m.
- Reinstall intake manifold with fresh gaskets; reconnect fuel lines and wiring connectors.
- Cycle ignition 3 times to prime system; start engine and inspect for fuel mist or combustion blow-by.
- Teflon Seal Resizing Mandate: Never stretch Teflon seals with fingers; always use the T10133 cone and sizing sleeve to prevent combustion blow-by.
- Bore Carbon Cleaning: Thoroughly clean injector bore carbon deposits before installing new injectors; carbon debris prevents proper seal seating.
- Even Rail Torquing: Torque fuel rail retaining bolts evenly in cross-pattern to prevent side-loading injector bodies.
Ariza Kodlari (DTC) ve Teshis Protokolleri
Bu common rail enjektorunde asinma, devre arizasi veya kalibrasyon kaymasi olustugunda tetiklenen yaygin ariza kodlari (DTC):
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Çapraz Referans ve Uyumluluk
Kardeş parça numaraları, aynı platform varyantları ve bilinen uyumsuzluklar.
Teknik Arıza Teşhis ve Servis Protokolleri
Bu parça grubu için doğrulanmış atölye prosedürleri, test eşik değerleri ve servis talimatları.