P0300: Rastgele veya Çoklu Silindirde Yanma Teklemesi Tespit Edildi
Diyagnostik Hata Kodu (DTC) P0300; Motor Kontrol Ünitesinin (ECU/PCM) birden fazla motor silindirinde rastgele, aralıklı veya sürekli yanma teklemesi (misfire) algıladığını gösterir. Buji bulunmayan ve doğrudan sıkıştırmayla ateşlemeye dayanan dizel ortak hat (common rail) sistemlerinde tekleme tespiti; yalnızca Krank Mili Pozisyon (CKP) sensörünün her silindirin Üst Ölü Nokta (ÜÖN) iş strokunun ardından krank mili açısal ivmelenmesindeki mikrosaniye altı değişimleri ölçmesiyle hesaplanır. Birden fazla silindir beklenen dönme torku darbesini üretemezse veya yanma kararsızlığı silindirler arasında rastgele geçiş yaparak kalibre edilmiş eşik değerlerini (tipik olarak toplam yanma çevrimlerinin >%2,0'sini) aşarsa P0300 arıza kodu kaydedilir.
🚗 Sürüş Güvenliği, Tahmini Onarım Maliyeti ve Doğrulama
- 01
🚦 Sürüş Güvenliği ve Mekanik Risk
Acil mekanik değerlendirme ve çekici gereksinimiRastgele / Çoklu Silindir Yanma Teklemesi - Yanıp Sönen Motor Arıza Lambası Uyarısı
Birden fazla silindirde düzgün yanma gerçekleşmiyor. Motor Arıza Lambası SABİT yanıyorsa, aracı zorlamadan düşük devirde doğrudan servise sürün. Motor Arıza Lambası YANIP SÖNÜYORSA, egzoz katalizörünün ve DPF'nin erimesini önlemek için aracı derhal güvenli bir yere çekip motoru durdurun.
SÜRÜŞE DEVAM EDİLMESİ DURUMUNDA MOTOR RİSKLERİ:Yanmamış ham mazotun silindir cidarındaki yağ filmini yıkayarak gömlek çizilmesine (bore score) yol açması, DPF içinde kontrolsüz alev alarak seramik monolit çekirdeğin erimesi ve dengesiz tork darbeleri nedeniyle çift kütleli volan (DMF) yaylarının kırılması. - 02
💰 Servis Onarım Bütçesi
Beklenen parça değişimi ve servis işçilik maliyet kademeleriKüçük Bakım / Filtre Temizliği1.500 TL - 4.500 TL ($40 - $120) (Kirlenmiş yakıtın tahliyesi / yakıt filtresi değişimi / akü voltaj kontrolü)Sensör temizliği, yakıt filtresi değişimi, sigorta kontrolü veya kablo soketi temizliği.
Valf / Sensör Değişimi7.000 TL - 18.000 TL ($180 - $450) (Yakıt dozaj valfi (SCV) değişimi veya ana motor şasi hattı onarımı)Tek bileşen değişimi (basınç regülatörü, dozaj valfi veya revizyonlu enjektör).
Ağır Onarım / Pompa ve Enjektörler60.000 TL - 140.000 TL ($1.600 - $3.500) (Çoklu enjektör değişimi veya ortak hat yüksek basınç pompası revizyonu)Yüksek basınç pompası revizyonu, yeni OEM enjektör takımı veya DPF değişimi.
- 03
🧰 Hızlı Görsel ve Fiziksel Kontroller
Servisi aramadan önce aletsiz 5 dakikalık hızlı kontrol1Arıza akaryakıt istasyonundan yakıt aldıktan hemen sonra mı başladı? Dizel depoya yanlışlıkla benzin doldurulması veya yakıta su karışması P0300 kodunun 1 numaralı sebebidir.212V akü kutup başlarını ve motor bloğu ana şasi kablosunu kontrol edin: Düşük sistem voltajı (<11,5V), ECU enjektör tetikleme sürücülerinin kilitlenmesine neden olur.3Şeffaf alçak basınç yakıt hatlarını gözlemleyin: Yüksek basınç pompasına doğru köpük veya hava kabarcığı geçişi varsa, yakıt hattı hızlı bağlantı rekorlarının O-ring contalarını değiştirin. - 04
🛡️ Yanıltıcı Arıza Teşhisine Karşı Koruma
Gereksiz parça değişimini önlemek için tamirciye sorulacak sorular"Servise iletin: 'Yüksek maliyetli mekanik revizyona karar vermeden önce lütfen yakıt filtre haznesinden şeffaf bir kaba numune alarak su/benzin ayrışmasını kontrol edin, alçak basınç besleme hattını ölçün ve enjektör geri dönüş testi uygulayın.'"
Teknik Not: Yüksek maliyetli parça değişimini onaylamadan önce ustanıza bu soruları yöneltin:
30 Saniyelik Hızlı Atölye Triyajı
- Severe, violent engine shaking, stumbling, and rough running throughout idle and low-RPM acceleration
- Noticeable loss of engine power, sluggish response, and intermittent bogging under vehicle load
- Flashing or steady Check Engine Light (MIL), often triggering Limp-Home Mode engine derate
- Aerated low-pressure fuel supply: air entering fuel lines through cracked filter housing, damaged quick-connect O-rings, or fuel line rub-through
- Severely restricted fuel filter or failing electric lift pump causing low-pressure fuel starvation to the high-pressure pump
- Fuel contamination: water emulsion, gasoline mixed into diesel, or winter wax crystallization plugging filter pores
Connect scan tool live telemetry: compare Target Fuel Rail Pressure vs Actual Rail Pressure and log metering valve command PWM duty cycle during idle and road load.
The $4,000 Multi-Injector Shotgun Blunder: Missing Low-Pressure Fuel Aeration and Clogged Lift Pump Strainers
When P0300 is logged with violent engine stumbling across multiple cylinders, shops frequently condemn all 4 to 8 common rail fuel injectors or declare the engine has suffered internal valve/compression loss, quoting $3,500 - $6,000 for full injector replacement or cylinder head teardown.
A single bad injector causes an isolated cylinder code (P0301-P0308). A random multi-cylinder code (P0300) almost always stems from a SYSTEMIC supply breakdown: micro-air ingress on the suction side of the fuel filter (aerated diesel compressing into hydraulic cushions in the rail), fuel wax/water contamination, or an EGR valve stuck partially open flooding all cylinders with exhaust gas.
Plumb a temporary transparent clear vinyl tube between the fuel filter outlet and the high-pressure pump inlet. Idle the engine and observe with a flashlight: if a continuous stream of microscopic fizz or air bubbles is visible, air is being drawn past quick-connect O-rings ($8 fix). Next, unbolt and block the EGR valve with a solid blanking plate: if idle instantly smooths out, the EGR valve was drowning the combustion chambers.
En Çok Etkilenen Motorlar ve Enjeksiyon Sistemleri
Bu arıza kodu öncelikle aşağıdaki common rail dizel platformlarını etkiler. Fabrika arıza modelleri ve parça numaraları için motor ailenizi inceleyin:
Volkswagen / Audi 2.0 TSI EA888 Gen 3 (Golf GTI, Golf R, Audi A4, Q5)
Bosch HDEV-5 Direct Injection (200 bar, 6-Hole Multi-Hole Laser Nozzle)Tipik Belirti: Severe engine stumbling, rough idle at cold start, and flashing Check Engine Light; misfire counter increments rapidly on Cylinders 2 & 3.
Bilinen Fabrika Arıza Modeli: GDI injector multi-hole tip heavy carbon encrustation disrupting fine fuel atomization; micro-leakage causing fuel puddling on piston crown overnight.
06L906036K / Bosch 0261500162 (GDI Injector)BMW 2.0T N20 & 3.0T N55 (328i, 335i, 528i, 535i, X3, X5 35i)
Bosch HDEV-5 Solenoid High-Pressure Direct Injection (200 bar)Tipik Belirti: Violent engine shake and drivetrain error warning during cold idle; black exhaust puff on startup and spark plugs soaked in liquid fuel.
Bilinen Fabrika Arıza Modeli: Solenoid needle valve failing to seat tightly when engine is off, bleeding high-pressure rail fuel into combustion chamber; Teflon sealing ring thermal degradation.
13647597870 / Bosch 0261500109 (GDI Injector)Mercedes-Benz 3.0T BiTurbo V6 & 3.5L CGI M276 (C400, C43 AMG, E400, ML350, GLE43)
Bosch HDEV-5 High-Pressure Direct Injection (200 bar)Tipik Belirti: Prolonged cranking followed by rough, rhythmic idle shaking; fuel odor in cabin; random multi-cylinder misfires under highway cruising.
Bilinen Fabrika Arıza Modeli: Precision laser spray micro-orifices clogged with fuel varnish and carbon deposits; internal needle guide wear resulting in asymmetrical spray patterns.
A2760700587 / Bosch 0261500065 (GDI Injector)Honda Civic Type R (FK8/FL5 K20C1) & Accord 2.0T Sport
Keihin High-Flow Direct Fuel Injection (200 bar)Tipik Belirti: Hesitation and sudden backfire/misfire at high-RPM (5,000+ RPM) under boost; P0300 and P0304 logged simultaneously after track or spirited driving.
Bilinen Fabrika Arıza Modeli: Microscopic deposit accumulation on high-flow injector nozzles causing lean misfires at high fuel demand; combustion chamber Teflon seal leakage allowing hot blowby gases.
16450-5BF-A01 / Keihin 16010-5BF-305 (GDI Injector)Toyota & Lexus 2.0T 8AR-FTS D-4S (Highlander, Lexus IS200t, NX200t, GS200t)
Denso D-4S Dual Injection (Direct + Port Injection, 200 bar)Tipik Belirti: Unsteady idle vibration when switching from port injection to pure direct injection; check engine light with multiple random misfire codes.
Bilinen Fabrika Arıza Modeli: Direct injection nozzle tip carbon baking from low-load combustion residues; direct injector Teflon seal hardening causing compression leakage.
23209-39145 / Denso 23209-31105 (GDI Injector)Ford F-250 / F-350 / F-450 Super Duty 6.7L Powerstroke V8
Bosch CP4.2 High-Pressure Common Rail (Piezo CRI3)Tipik Belirti: Extreme cab and steering wheel shudder under highway towing load; tachometer needle fluctuates violently by 300-500 RPM accompanied by Water in Fuel (WIF) warning.
Bilinen Fabrika Arıza Modeli: Water contamination slipping past secondary fuel filter, stripping CP4.2 pump cam roller lubrication and shedding metallic glitter into multiple injector nozzles simultaneously.
FD-4615 (Primary/Secondary Fuel Filter Kit) / BC3Z-9324-A (Low-Pressure Return Line Assembly)BMW 3.0d M57N / N57 Straight-6 (330d, 530d, 730d, X5 3.0d / 35d)
Bosch CRI3 Piezo Common Rail SystemTipik Belirti: Engine suddenly enters rough 3-cylinder Limp-Home Mode under full-throttle kickdown; Drivetrain Malfunction warning appears on center iDrive screen.
Bilinen Fabrika Arıza Modeli: A single piezo actuator element suffering internal insulation breakdown (short-to-ground); ECM safety logic automatically cuts power to the entire common capacitor bank of 3 cylinders.
13537796042 / Bosch 0445115077 (Piezo Injector) / 13537800602 (Return Line)Cylinder Balance & Injector Deviation Guide
Common rail diesel cylinder balance & smooth running diagnostic guide. Balance rates, mg/stroke deviation, P0263 misfire, compression vs injector test.
Kontrol Devresi ve Aktüatör Çalışma Mantığı
1. Dynamic In-Demand Fuel Metering
Diesel combustion depends on three immutable physical factors: adequate cylinder compression (>22 bar producing air temperatures above 500°C), precise atomization of high-pressure diesel fuel (>250 bar cranking, >1400 bar running), and exact injection timing. The ECM monitors instantaneous flywheel tooth passage times using a high-resolution Hall-effect or magnetic inductive CKP sensor reading a 60-2 or 36-2 target wheel. When a cylinder fires properly, the crankshaft accelerates rapidly between 15° and 45° After Top Dead Center (ATDC). A weak combustion stroke results in a measurable deceleration dip (micro-hesitation) during that segment.
2. Closed-Loop PID Deviation Monitoring
The ECM operates Smooth Running Control (SRC) / Zero Fuel Calibration (ZFC) software algorithms. To maintain a smooth, vibration-free idle, the ECM calculates a real-time cylinder balance correction value (typically ±2.5 to ±4.0 mg/stroke of fuel) for each individual cylinder. If the required compensation on multiple cylinders exceeds calibrated limits (±3.0 mg/stroke), or if the rotational speed fluctuations are so chaotic that the ECM cannot isolate a single failing cylinder (such as when air bubbles permeate the high-pressure fuel rail or the EGR valve is stuck wide open), the ECM records the multi-cylinder code P0300.
3. Diagnostic Trap: Normally Open (NO) vs Normally Closed (NC) Valves
Systemic Misfire & Solenoid vs Piezo Architecture: Single-cylinder misfires (P0301-P0304) stem from localized faults, whereas P0300 reflects systemic breakdown (aerated fuel, clogged filter, bad batch of fuel, compression loss). On Piezo common rail engines (Bosch CRI3, Siemens/Continental, Denso), the ECM drives injectors in banked capacitor pairs (e.g., Cyl 1+4, Cyl 2+3). A single shorted piezo stack (< 180 kΩ or capacitance < 2.5 µF) will immediately trigger high-voltage safety shutdown of the entire bank or ECM injector driver, causing simultaneous multi-cylinder shutdown and random misfire codes P0300/P2146/P2149 rather than an isolated single-cylinder misfire.
Elektriksel ve Hidrolik Fiziksel Standartlar
Adım Adım Atölye Teşhis Protokolü
Transparent Fuel Line Air Micro-Bubble Inspection
Install a temporary transparent clear vinyl fuel line between the primary fuel filter outlet and the high-pressure pump inlet. Start engine and shine a bright light through the clear line while revving between idle and 2500 RPM. The fuel stream must be crystal clear. Any foaming, steady train of microscopic bubbles, or air pockets confirms that air is being sucked into the suction line, causing erratic injection volume across random cylinders.
Scan Tool Cylinder Balance (Smooth Running Control) Evaluation
With the engine at full operating temperature (coolant >80°C), access scan tool live data for 'Cylinder Balancing / Injector Quantity Offsets'. Observe the real-time trim for all cylinders. Normal values are between -1.0 and +1.0 mg/stroke. If multiple cylinders are pegged at maximum enrichment (+3.0 to +5.0 mg/stroke) while others are pulled lean (-3.0 to -5.0 mg/stroke), multi-cylinder hydraulic imbalance is confirmed.
Low-Pressure Supply Quality & Fuel Contamination Testing
Draw a 500 mL fuel sample from the fuel filter water drain into a clear glass jar. Allow it to settle for 10 minutes. Inspect for phase separation (water layer at the bottom), cloudy white emulsion, dark asphaltine sludge, or gasoline odor. Place a drop on white paper: diesel leaves an oily stain, while gasoline evaporates quickly within 60 seconds.
Automated Relative Compression & Mechanical Gauge Compression Test
Perform an electronic 'Relative Compression Test' via diagnostic scan tool, which monitors starter motor current draw and crankshaft deceleration across each compression stroke. If all cylinders show >95% balance, proceed to fuel testing. If one or more cylinders show <80%, remove glow plugs and perform a physical mechanical compression gauge test (must exceed 22 bar with <3 bar variance).
Dynamic Injector Backleak (Return Flow) Multi-Cylinder Test
Disconnect the injector fuel return lines. Connect individual graduated measurement tubes to all injector return nipples. Idle engine for exactly 2 minutes (or crank for 15 seconds if engine will not start). Measure return volume in milliliters. If multiple injectors exceed 25-35 mL/min at idle, worn internal control valves are causing hydraulic rail pressure loss that starves injection pulses.
EGR Valve Seat Sealing & Intake Choke Audit
Remove the EGR valve or insert a temporary solid metal blocking plate into the EGR pipe flange. Start the engine and re-evaluate idle smoothness. If the random misfire immediately disappears and idle stabilizes, the EGR valve was leaking exhaust gas into the intake plenum at idle, displacing oxygen and causing multiple cylinders to flame out.
Donanım Onarımı ve Yedek Parça Listesi (BOM)
Isolate systemic fuel supply, ignition, and direct injector sealing before replacing complete engine harnesses or assemblies:
0261500162 / 06L906036KBosch
High-pressure multi-hole GDI fuel injector. Delivers precise conical spray pattern, eliminating random cylinder misfires and cold rough idle.
0261500109 / 13647597870Bosch
OEM direct fuel injector for N20 4-cylinder and N55 6-cylinder turbo engines. Eliminates cold-start cylinder wash and fuel weeping.
0261500065 / A2760700587Bosch
Precision high-pressure direct fuel injector for Mercedes-Benz BiTurbo V6 and CGI engines. Resolves highway misfires.
16450-5BF-A01 / 16010-5BF-305Keihin
Original factory high-flow direct fuel injector for 2.0T turbocharged Honda platforms. Eliminates high-RPM lean misfires.
23209-39145 / 23209-31105Denso
OEM direct-in-cylinder fuel injector with virgin Teflon combustion seal ring for D-4S dual-injection engines.
Canlı Common Rail Tolerans Hesaplayıcı
İlgili Common Rail Parçaları
The following genuine OEM fuel pumps and common rail injectors are verified factory equipment for engines reporting fault protocol P0300. Cross-reference operating pressures and tightening torques before sub-assembly replacement:
0445115077BOSCH
BOSCH 0445115077 Piezo Common Rail Injector for BMW 330d / 530d / X5 3.0d M57N2
View Technical Specs & Fitment →095000-5880Denso
095000-5880 Denso Toyota 2KD-FTV Injector: 23670-30050 Data
View Technical Specs & Fitment →28337917Delphi
28337917 Delphi Bobcat D24 Injector: 7030364 Specs & Data
View Technical Specs & Fitment →095000-8340Denso
095000-8340 Denso Mitsubishi 4D56 HP Injector: 1465A367 Data
View Technical Specs & Fitment →0445120289Bosch
0445120289 Bosch Perkins 1104D Injector: 2645A749 Data
View Technical Specs & Fitment →0445120357Bosch
0445120357 Bosch Cummins ISDe 6.7L Injector: 4988835 Data
View Technical Specs & Fitment →Yüksek Basınç Pompası Adaptasyon Sıfırlama ve Test
Following fuel system repair, filter replacement, or injector renewal, the ECM must relearn cylinder balance and pilot injection values:
1. Clear all stored diagnostic trouble codes and confirm engine coolant temperature is above 75°C (167°F).
2. Ensure all newly installed injectors have their IMA / QR calibration codes correctly programmed into the ECM.
3. Select 'Reset Cylinder Balance Learning Values' (or 'Zero Fuel Calibration Reset') in the scan tool special functions menu.
4. Start the engine and let it idle in neutral for 5 minutes without touching any pedals or electrical loads (A/C off).
5. Accelerate vehicle smoothly in 4th gear to 80 km/h (2200 RPM), then release throttle completely to coast down in gear to 35 km/h (minimum 8 seconds overrun).
6. Repeat this acceleration and coast-down sequence 5 times to allow the ECM to calibrate minimum pilot delivery thresholds for each cylinder.
Diferansiyel Teşhis ve İlgili Hata Kodları
Cylinder 1 Misfire Detected
Single-cylinder isolated misfire: points to a localized fault on Cylinder 1 (injector, glow plug, or compression) rather than the systemic multi-cylinder causes of P0300.
Fuel Rail/System Pressure - Too Low
Frequent root cause: low high-pressure rail delivery starves all injectors of pressure, triggering random multi-cylinder misfires.
Exhaust Gas Recirculation (EGR) Flow Insufficient
Related EGR system fault: carbon-restricted or stuck EGR valves alter intake charge oxygen ratios, causing erratic combustion stumbling.
Atölye Saha Vaka İncelemeleri
Sıkça Sorulan Teknik Sorular
P0300 motor arıza kodu ne anlama gelir?
Diyagnostik Hata Kodu (DTC) P0300; Motor Kontrol Ünitesinin (ECU/PCM) birden fazla motor silindirinde rastgele, aralıklı veya sürekli yanma teklemesi (misfire) algıladığını gösterir. Buji bulunmayan ve doğrudan sıkıştırmayla ateşlemeye dayanan dizel ortak hat (common rail) sistemlerinde tekleme tespiti; yalnızca Krank Mili Pozisyon (CKP) sensörünün her silindirin Üst Ölü Nokta (ÜÖN) iş strokunun ardından krank mili açısal ivmelenmesindeki mikrosaniye altı değişimleri ölçmesiyle hesaplanır. Birden fazla silindir beklenen dönme torku darbesini üretemezse veya yanma kararsızlığı silindirler arasında rastgele geçiş yaparak kalibre edilmiş eşik değerlerini (tipik olarak toplam yanma çevrimlerinin >%2,0'sini) aşarsa P0300 arıza kodu kaydedilir.
P0300 kodunun en yaygın belirtileri nelerdir?
Severe, violent engine shaking, stumbling, and rough running throughout idle and low-RPM acceleration, Noticeable loss of engine power, sluggish response, and intermittent bogging under vehicle load, Flashing or steady Check Engine Light (MIL), often triggering Limp-Home Mode engine derate, Heavy white or grey smoke from exhaust on cold start (unburned fuel atomized but not ignited due to low compression or late timing), Strong odor of unburned diesel fuel emanating from exhaust pipe and engine compartment, Cylinder balance live data showing erratic, jumping compensation values exceeding ±3.5 mg/stroke across multiple cylinders.
Dizel motorda P0300 arızasına ne sebep olur?
Aerated low-pressure fuel supply: air entering fuel lines through cracked filter housing, damaged quick-connect O-rings, or fuel line rub-through; Severely restricted fuel filter or failing electric lift pump causing low-pressure fuel starvation to the high-pressure pump; Fuel contamination: water emulsion, gasoline mixed into diesel, or winter wax crystallization plugging filter pores; Excessive internal control valve backleak across multiple fuel injectors, dropping cranking and idle rail pressure; Exhaust Gas Recirculation (EGR) valve stuck partially open, flooding all intake runners with inert exhaust and extinguishing combustion; Low mechanical cylinder compression across multiple cylinders caused by worn piston rings, valve seat recession, or blown head gasket.
P0300 kodu etkinken araç sürmek güvenli midir?
🔴 Kritik: Sürüşü Durdurun / Çekici Gerekli
P0300 arıza kodunun tamir maliyeti ne kadardır?
P0300 arıza kodu için tipik onarım maliyetleri kök nedene ve teşhis seviyesine bağlıdır: Seviye 1 (Hafif Onarım / Bakım): 1.500 TL - 4.500 TL ($40 - $120) (Kirlenmiş yakıtın tahliyesi / yakıt filtresi değişimi / akü voltaj kontrolü) (Sensör temizliği, yakıt filtresi değişimi, sigorta kontrolü veya kablo soketi temizliği.); Seviye 2 (Parça Değişimi): 7.000 TL - 18.000 TL ($180 - $450) (Yakıt dozaj valfi (SCV) değişimi veya ana motor şasi hattı onarımı) (Tek bileşen değişimi (basınç regülatörü, dozaj valfi veya revizyonlu enjektör).); Seviye 3 (Komple Revizyon): 60.000 TL - 140.000 TL ($1.600 - $3.500) (Çoklu enjektör değişimi veya ortak hat yüksek basınç pompası revizyonu) (Yüksek basınç pompası revizyonu, yeni OEM enjektör takımı veya DPF değişimi.). Servis referans fiyatları. Arızaların %70'inden fazlası komple parçalar değiştirilmeden Seviye 1 veya 2 dahilinde çözülür.
Can air in the diesel fuel lines cause trouble code P0300?
Yes, air in the low-pressure fuel system is one of the most common causes of random multi-cylinder misfire P0300 in diesel engines. Because air is compressible while liquid diesel is incompressible, microscopic air bubbles entering the high-pressure pump become compressed in the common rail. This creates unpredictable pressure cushion drops that starve random injector nozzles of fuel, causing erratic misfiring that jumps from cylinder to cylinder.
Why does a diesel engine misfire show up as a violent vehicle shake rather than a gentle hesitation?
Diesel engines have extremely high compression ratios (between 16:1 and 21:1) and generate tremendous cylinder torque (often 300 to 1000+ Nm). Each cylinder's combustion stroke produces a massive rotational impulse on the crankshaft. When one or more cylinders fail to fire, the sudden loss of that massive torque stroke combined with the heavy drag of compressing cold air creates a severe rotational shockwave through the flywheel, shaking the entire vehicle violently.
Can bad glow plugs cause code P0300 in a common rail diesel engine?
Yes, but primarily during cold starting and the initial 3 to 5 minutes of engine warm-up (post-glow phase). Modern diesel engines utilize glow plugs not just to start the engine, but to maintain cylinder combustion temperatures during post-start idle until the cylinder head reaches 60°C. If multiple glow plugs have burned out, cold cylinders will fail to achieve the 500°C auto-ignition threshold at idle, resulting in heavy white unburned fuel smoke and P0300 misfiring until the engine warms up.