PE01-13-350
DENSO PE01-13-350 Yüksek Basınç Pompası Mazda Skyactiv-G 2.0L
PE01-13-350, PE01-13-350A, PE01-13-350B, PE01-13-350C, PY01-13-350Integrated Solenoid Suction Control Spill Valve (SCV)-200 barÜrüne Genel Bakış
The Denso PE01-13-350 (Mazda OE PE01-13-350A / PE01-13-350B / PY01-13-350) is the genuine original equipment high-pressure fuel pump for Mazda Skyactiv-G 2.0L and 2.5L naturally aspirated and turbocharged engines. Driven by the exhaust camshaft via an anti-friction bucket lifter, this Denso single-piston pump delivers up to 200 bar (20 MPa) injection pressure. Standard fitment on Mazda 3, Mazda 6, CX-5, and CX-30 models, it features an integrated electronic suction control valve. Typical failure symptoms include long start cranking times, surging idle, and diagnostic code P0087.
HIGH-COMPRESSION GDI MISFIRE & SUCTION VALVE STICKING: Mazda Skyactiv-G engines utilize an ultra-high 13:1 to 14:1 compression ratio, requiring precise 200 bar fuel delivery. When the Denso PE01-13-350 suction control valve sticks from fuel varnish or the internal discharge check valve leaks, low rail pressure causes severe cold-engine hesitation, misfire codes P0300/P0301, and DTC P0087 under highway load.
Uyumlu Araçlar ve Motorlar
| Araç | Motor | Model Yılları |
|---|---|---|
| Mazda Mazda 3 2.0 / 2.5 | Mazda 2.0L & 2.5L SkyActiv-G / 2.5T Turbo (PE-VPS / PY-VPS / PY-VPTS) | 2014-2023 |
| Mazda CX-5 2.0 / 2.5 | Mazda 2.0L & 2.5L SkyActiv-G / 2.5T Turbo (PE-VPS / PY-VPS / PY-VPTS) | 2013-2023 |
| Mazda Mazda 6 2.5 | Mazda 2.0L & 2.5L SkyActiv-G / 2.5T Turbo (PE-VPS / PY-VPS / PY-VPTS) | 2014-2021 |
Teknik Özellikler
| Özellik | Değer |
|---|---|
| Pump Generation | Denso Single-Plunger High-Pressure Mechanical Fuel Pump |
| Operating Rail PressureTemel Değer | |
| Cam Drive Type | Exhaust Camshaft via Anti-Friction Bucket Lifter |
| Flow Regulation Control | Integrated Solenoid Suction Control Spill Valve (SCV) |
| Pump Flange Mounting Torque | 10 N·m + 90° (Even cross-pattern) |
| High Pressure Pipe Flare Nut Torque | 28 N·m |
| Tightening Torque | 28 N·m |
| Enjektör Baskı Çatalı Torku | 10 N·m |
| Primary OEM Reference | PE01-13-350, PE01-13-350A, PE01-13-350B, PY01-13-350 |
| Engine Emission Compliance | Euro 6 / LEV III / Tier 3 Bin 30 |
| Standard Industrial Warranty | 12 Months / Unlimited Mileage |
| Çalışma BasıncıTemel Değer |
Uyumlu Yüksek Basınç Pompası (Yakıt Devresi Grubu)
Aynı yüksek basınçlı Common Rail devresinde çalışır. Düşük basınç (P0087) teşhisinde enjektörleri değiştirmeden önce pompa debisini kontrol edin.
Montaj İpuçları
Gerekli ekipmanlar: 10mm socket and torque wrench calibrated for 10-30 N·m, 17mm line flare wrench for fuel line pipe nut, Clean engine oil for pump O-ring seal lubrication, Clean lint-free shop cloths and eye protection
- Disconnect negative battery terminal; depressurize fuel system before loosening fittings.
- Loosen high-pressure fuel line union nut slowly to vent residual fuel pressure safely.
- Disconnect electrical wiring connector from SCV spill valve solenoid.
- Disconnect low-pressure fuel supply hose.
- Loosen the two pump flange bolts evenly in half-turn increments to release spring tension.
- Remove pump body; inspect bucket lifter for surface wear or galling.
- Clean cylinder head mating surface and coat new O-ring seal with clean motor oil.
- Rotate engine until driving camshaft lobe is on base circle (lowest lift point).
- Seat pump square into bore; thread mounting bolts finger-tight.
- Torque mounting bolts alternately to 10 N·m plus an additional 90-degree angle turn.
- Hand-thread high-pressure pipe flare nut; torque to 28 N·m.
- Reconnect fuel lines and electrical harness; prime system and check for leaks.
- Angle Torque Specification: Always follow the 10 N·m + 90° specification; undertorquing allows vibration loosening while overtorquing strips aluminum threads.
- Inspect Lifter Surface: Check the bucket lifter contacting the camshaft for scratches; replace lifter if discolored or worn.
- Lubricate O-Ring: Never install the pump dry; lubricate the Viton O-ring with clean engine oil to prevent tearing during installation.
Ariza Kodlari (DTC) ve Teshis Protokolleri
Bu common rail enjektorunde asinma, devre arizasi veya kalibrasyon kaymasi olustugunda tetiklenen yaygin ariza kodlari (DTC):
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Çapraz Referans ve Uyumluluk
Kardeş parça numaraları, aynı platform varyantları ve bilinen uyumsuzluklar.
Teknik Arıza Teşhis ve Servis Protokolleri
Bu parça grubu için doğrulanmış atölye prosedürleri, test eşik değerleri ve servis talimatları.