16600-1KC0A
BOSCH 16600-1KC0A Yüksek Basınç Enjektörü Nissan Juke Tiida MR16DDT 1.6 DIG-T
16600-1KC0B, 0261500091, 0261500092, HDEV-5-2High-pressure electromagnetic solenoid needle valve-150 barUyumlu Araçlar ve Motorlar
Teknik Özellikler
| Özellik | Değer |
|---|---|
| Sistem Tipi | Bosch HDEV-5 Gasoline Direct Injection Multi-Hole Injector |
| Çalışma BasıncıTemel Değer | |
| Spray Pattern | Multi-hole targeted spray pattern towards piston crown bowl |
| Fuel Rail Bolt Torque | 21 N·m Fuel Rail Clamping Bolts |
| High Pressure Feed Line Torque | 30 N·m Flare Nut Connection |
| Coil Resistance | 1.4 - 1.8 Ω at 20°C (Direct peak-and-hold driver circuit) |
| Tipik Arıza Kodları | P0171 (System Too Lean Bank 1), P0300 (Random Misfire), P0301-P0304 (Cylinder Misfire) |
| Workshop Precaution | Replace Teflon combustion seal ring CM-5250 and lubricate fuel rail O-ring with clean motor oil |
Uyumlu Yüksek Basınç Pompası (Yakıt Devresi Grubu)
Aynı yüksek basınçlı Common Rail devresinde çalışır. Düşük basınç (P0087) teşhisinde enjektörleri değiştirmeden önce pompa debisini kontrol edin.
Montaj İpuçları
- [
- {
- "step": 1,
- "title": "Release Fuel Pressure & Remove Charge Pipes",
- "instruction": "Depressurize high-pressure fuel circuit. Disconnect intercooler charge piping and intake runners to access the high-pressure fuel rail."
- },
- {
- "step": 2,
- "title": "Remove High Pressure Rail Assembly",
- "instruction": "Disconnect electrical wiring harness clips. Undo rail mounting bolts (21 N·m) and withdraw fuel rail with injectors from the cylinder head."
- },
- {
- "step": 3,
- "title": "Replace Teflon Chamber Seals & Viton O-Rings",
- "instruction": "Remove old Teflon seal using plastic pick. Stretch new Teflon ring over guide cone and compress into groove. Install new viton rail O-rings."
- },
- {
- "step": 4,
- "title": "Reinstall Rail & Torque Fasteners",
- "instruction": "Lubricate upper O-rings with clean engine oil. Insert injectors squarely into cylinder head bores. Torque fuel rail bolts to 21 N·m and fuel line to 30 N·m."
- }
- ]
Ariza Kodlari (DTC) ve Teshis Protokolleri
Bu common rail enjektorunde asinma, devre arizasi veya kalibrasyon kaymasi olustugunda tetiklenen yaygin ariza kodlari (DTC):
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Teknik Arıza Teşhis ve Servis Protokolleri
Bu parça grubu için doğrulanmış atölye prosedürleri, test eşik değerleri ve servis talimatları.