HITACHI
03C127026R
Özellikleri Gör
SolenoidHitachi / Bosch FSI/TSI 150-bar High Pressure Direct InjectionEuro 45
HITACHI 03C127026R Yüksek Basınç Pompası VW Golf 6 Tiguan 1.4
OEM REFERANSI
03C127026P, 03C127026M, 03C127026J, HPP0005, HM10018KONTROL VALFİ
Integrated Fuel Metering Valve N290ENJEKTÖR MEMESİ
-RAİL BASINCI
150 barEMİSYONEuro 4 / Euro 5
GARANTİ12 Ay
02
Uyumlu Araçlar ve Motorlar
| Araç | Motor | Model Yılları |
|---|---|---|
| Volkswagen Golf Mk5 / Mk6 / Scirocco / Tiguan | Volkswagen 1.4L TSI DOHC 16V Twincharger / Turbo EA111 (CAXA / CAVE / CAVD / CTHD / BLG / BMY) | 2006-2015 |
| Audi A1 8X / A3 8P | Volkswagen 1.4L TSI DOHC 16V Twincharger / Turbo EA111 (CAXA / CAVE / CAVD / CTHD / BLG / BMY) | 2007-2014 |
03
Teknik Özellikler
| Özellik | Değer |
|---|---|
| Çalışma BasıncıTemel Değer | |
| Pump Technology | Single Plunger Mechanical Camshaft-Driven HPFP |
| Flow Control | Integrated Solenoid Metering Valve (N290) |
| Mounting Flange Torque | 20 N·m |
| High Pressure Line Torque | 27 N·m |
| Drive Type | Intake Camshaft Driven with Roller Tappet |
| Fuel Type | Gasoline / Petrol Direct Injection (TSI / TFSI / Twincharger) |
| OE Cross References | 03C127026R, 03C127026P, 03C127026M, 03C127026J, HPP0005 |
| Failure Symptoms | EPC warning lamp on acceleration, P0087 low rail pressure, hard starting, limp mode above 3000 RPM |
| Diagnostic Test | VCDS measuring block Group 106 & 140 (Specified vs Actual Rail Pressure under boost) |
04
Montaj İpuçları
- [
- "Disconnect battery; pull fuel pump fuse and crank engine for 5 seconds to depressurize fuel lines.",
- "Disconnect electrical connector to N290 metering valve and unfasten low-pressure feed hose clamp.",
- "Counter-hold pump discharge union and loosen high-pressure steel tube flare nut using a flare wrench.",
- "Loosen the two M6 mounting bolts evenly in alternating turns to release internal spring tension evenly.",
- "Withdraw HPFP and inspect roller tappet in the cylinder head bore for flat spots or surface galling.",
- "Fit a new sealing O-ring lubricated with clean engine oil; seat pump into mounting bore.",
- "Tighten mounting flange bolts progressively in alternating steps to 20 N·m.",
- "Hand-thread high-pressure line flare nut until seated, then torque to 27 N·m; reconnect N290 connector.",
- "Cycle ignition several times to bleed air; start engine and inspect all joints for leaks."
- ]
05
Ariza Kodlari (DTC) ve Teshis Protokolleri
Bu common rail enjektorunde asinma, devre arizasi veya kalibrasyon kaymasi olustugunda tetiklenen yaygin ariza kodlari (DTC):
P0087Critical
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
P0201 - P0208High
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
P0300 / P0301+High
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
P0088High
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
ATÖLYE PROTOKOLLERİ
Teknik Arıza Teşhis ve Servis Protokolleri
Bu parça grubu için doğrulanmış atölye prosedürleri, test eşik değerleri ve servis talimatları.
ATÖLYE COMMON RAIL ARIZA TEŞHİSİ
Teknik Kılavuzu OkuYüksek Basınç Pompası Arıza Teşhisi: P0087 ve Bosch CP4
COMMON RAIL ATÖLYE ARIZA TEŞHİSİ
Teknik Kılavuzu OkuYakıt Ölçüm Valfi IMV SCV Arıza Teşhisi: P0088 Test
OBD-II TEŞHİS PROTOKOLÜ
Teknik Kılavuzu OkuP0087 Düşük Rail Basıncı Teşhis Kılavuzu
COMMON RAIL SERVİS DİYAGNOSTİĞİ
Teknik Kılavuzu Oku