BOSCH
13537617365
Technische Daten
SolenoidBosch HDP5 / HDP6 Gasoline Direct Injection High-Pressure Pump (200 bar)Euro 56
BOSCH 13537617365 Hochdruckpumpe BMW 1 2 3 4 5 Serie X1 X3 X5 1.5L B38 2.0L B48 3.0L B58 0261520287
OE-REFERENZ
13538637896, 0261520287, 0261520288, GDP701, HM10038, HPP0028STEUERVENTIL
-EINSPRITZDÜSE
-BETRIEBSDRUCK
200 barABGASNORMEuro 5 / Euro 6
GARANTIE12 Monate
02
Fahrzeug- und Motorverwendung
| Fahrzeug | Motor | Baujahre |
|---|---|---|
| BMW M340i G20 / 540i G30 / X3 M40i | BMW B38 / B48 / B58 Modular TwinPower Turbo (1.5L / 2.0L / 3.0L & TU) | 2019-2024 |
| Toyota GR Supra A90 (B58 3.0T) | BMW B38 / B48 / B58 Modular TwinPower Turbo (1.5L / 2.0L / 3.0L & TU) | 2019-2024 |
| BMW 330i G20 / 430i G22 | BMW B38 / B48 / B58 Modular TwinPower Turbo (1.5L / 2.0L / 3.0L & TU) | 2019-2024 |
| BMW 340i F30 / M240i F22 (Retrofit) | BMW B38 / B48 / B58 Modular TwinPower Turbo (1.5L / 2.0L / 3.0L & TU) | 2015-2019 |
03
Technische Daten
| Spezifikation | Wert |
|---|---|
| part_number | 13537617365 |
| oem_reference | 13537617365 |
| manufacturer | BOSCH |
| system_type | High Pressure Fuel Pump |
| pressure_rating | 200 bar (2900 psi) |
| operating_temperature | -40°C to +135°C |
| flange_mount_torque | 13 N-m (115 lb-in) |
| high_pressure_line_torque | 30 N-m (22 lb-ft) |
| diagnostic_dtc | P0087, P0088, P0171, P0300 |
| BetriebsdruckKernwert |
SYSTEM-BAUGRUPPE
Passende Kraftstoffinjektoren (Kraftstoffkreislauf-Baugruppe)
Wird direkt von dieser Hochdruckpumpe versorgt. Rücklaufmenge prüfen, wenn der Raildruck beim Starten nicht ansteigt.
BOSCHExakte Motor- & Fahrgestell-Passung
13538625397Gasoline Direct Injection (GDI) • 200 bar
🚙 Bmw 3 Series (F30) / 2 Series (F22) (B38)
BOSCHExakte Motor- & Fahrgestell-Passung
13538656548Gasoline Direct Injection (GDI) • 350 bar
🚙 Bmw 3 Series (F30) / 2 Series (F22) (B38)
BOSCHExakte Motor- & Fahrgestell-Passung
13538625396Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code B38
BOSCHExakte Motor- & Fahrgestell-Passung
13648625597Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code B38
04
Einbauhinweise
- Depressurize the fuel system completely via diagnostic scan tool or by removing the fuel pump fuse prior to line disassembly.
- Clean all surrounding bracket areas thoroughly using residue-free brake cleaner to prevent abrasive particulate ingress.
- Inspect the mechanical camshaft lobe and roller follower or clean injector bore seating surfaces before hardware alignment.
- Install component using fresh factory O-rings or Teflon combustion chamber seals lubricated only with clean motor oil.
- Torque mounting flange fasteners in alternating increments to 13 N-m (115 lb-in).
- Torque high-pressure hydraulic tube fittings using a calibrated flare nut wrench to 30 N-m (22 lb-ft).
- Prime low-pressure fuel circuit, cycle ignition key 3-4 times, and inspect for high-pressure hydraulic leaks before road test.
Hinweise & Warnungen:
- Always replace single-use high-pressure metal fuel lines and micro-filter seals whenever disconnected.
- Verify camshaft driving lobe surfaces for scoring or flat spots before installing any mechanical pump.
- Reset long-term and short-term fuel trim adaptations via OBD-II diagnostic scanner after physical replacement.
05
Fehlercodes (DTC) & Diagnoseprotokolle
Häufige Diagnose-Fehlercodes (DTCs), die ausgelöst werden, wenn dieser Common-Rail-Injektor Verschleiß, Schaltkreisfehler oder Kalibrierungsabweichungen aufweist:
P0087Critical
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
P0201 - P0208High
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
P0300 / P0301+High
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
P0088High
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
WERKSTATT-LEITFÄDEN
Technische Diagnose- & Service-Protokolle
Verifizierte Prüfverfahren, Fehlercode-Grenzwerte und Werkstatt-SOPs für diese Baugruppe.
COMMON-RAIL WERKSTATT-DIAGNOSE
Technischen Leitfaden lesenHochdruckpumpe Diagnose: P0087 Fehler & Bosch CP4 Test
COMMON-RAIL WERKSTATT-DIAGNOSE
Technischen Leitfaden lesenZumesseinheit ZME IMV SCV Diagnose: P0088 Fehlertest
OBD-II-DIAGNOSEPROTOKOLL
Technischen Leitfaden lesenDiagnoseleitfaden P0087: Raildruck zu niedrig
COMMON-RAIL WERKSTATT-DIAGNOSE
Technischen Leitfaden lesen