P0272: Défaut d'équilibrage / contribution de couple du cylindre 4
Le code défaut P0272 indique que le calculateur de gestion moteur a détecté que le cylindre 4 ne fournit pas l'impulsion de couple mécanique théorique au vilebrequin, générant un déséquilibre de rotation inter-cylindres (défaut d'acyclisme). Sur les moteurs diesel à rampe commune, le calculateur calcule en continu le travail individuel de chaque cylindre en mesurant les micro-variations de l'accélération angulaire via le capteur de position vilebrequin (capteur PMH) durant la phase de détente, entre 30° - 90° après le point mort haut (PMH). Si l'algorithme de régulation de circularité / correction de débit applique une compensation excessive (typiquement supérieure à +3,0 - +4,5 mg/coup) pour stabiliser le ralenti, ou si la contribution chute de 15% - 25% sous la moyenne moteur, le code P0272 est enregistré.
🚗 Sécurité d'exploitation, coûts typiques et vérification diagnostique
- 01
🚦 Sécurité de conduite et risque mécanique
Évaluation immédiate et nécessité de remorquageDéfaut d'équilibrage / contribution du cylindre 4 - Anomalie de combustion sur le dernier cylindre
Le taux de contribution du cylindre 4 est hors tolérance. Situé en bout de rampe commune haute pression, le cylindre 4 est particulièrement sujet au dépôt de micro-impuretés et aux contraintes thermiques élevées.
RISQUES MÉCANIQUES EN CAS DE CONDUITE PROLONGÉE :Les acyclismes de combustion déséquilibrés augmentent les contraintes sur les coussinets de bielle et les tourillons de vilebrequin. - 02
💰 Budget typique de réparation en atelier
Fourchettes de coûts prévues pour pièces et main-d'œuvreEntretien léger / Purge filtre40 € - 110 € : Remplacement du filtre à carburant premium et nettoyage des injecteurs dieselNettoyage de capteur, remplacement du filtre à carburant, contrôle de fusible ou des connecteurs.
Remplacement vanne / Capteur180 € - 480 € : Remplacement de l'injecteur Common Rail d'origine du cylindre 4Remplacement d’un composant (régulateur de pression, vanne de dosage ou injecteur reconditionné).
Réfection majeure / Pompe et injecteurs850 € - 2 200 € : Contrôle des compressions mécaniques ou inspection de l'usure des cames d'arbre à camesRévision de pompe haute pression, jeu d’injecteurs neufs ou remplacement de l’ensemble FAP.
- 03
🧰 Vérifications visuelles et simples au garage
Diagnostic rapide en 5 minutes sans outil avant d'appeler le garage11. Surveiller les corrections de débit de cylindre sur l'outil de diagnostic ; vérifier que l'écart du cylindre 4 dépasse le seuil constructeur.22. Test comparatif de retour de fuite : mesurer le débit de retour dans des éprouvettes graduées pendant 3 minutes au ralenti moteur chaud.33. Vérifier le connecteur électrique et l'intégrité du faisceau à l'arrière de la culasse, près du tablier. - 04
🛡️ Bouclier anti-surfacturation mécanicien
Questions précises à poser pour éviter les remplacements inutiles de pièces""Vérifiez le comparatif des volumes de retour de fuite avant de déclarer l'injecteur du cylindre 4 défaillant.""
""Inspectez le profil des cames et les poussoirs hydrauliques du cylindre 4 pour écarter un déficit de levée de soupape.""
""Télécodez le code IMA du nouvel injecteur dans l'ECU moteur et réalisez un cycle d'apprentissage adaptatif haute pression.""
Note technique : Posez ces questions techniques à votre mécanicien avant d'accepter des devis élevés :
Triage atelier en 30 secondes
- Noticeable engine shudder, rough idle, and cabin vibration during warm idle (especially in Drive at traffic lights)
- Hesitation, flat spots, or rhythmic surging during light-to-moderate throttle cruising at 1200 to 2000 RPM
- Check Engine Light (MIL) illuminated, occasionally accompanied by flashing glow plug light or traction control warning
- Partially clogged, carbon-coked, or eroded spray holes in the Cylinder 4 fuel injector nozzle tip
- Excessive internal control valve wear (backleak) in Cylinder 4 injector, reducing effective injection pressure and fuel delivery
- Incorrect, corrupted, or uncalibrated IMA / QR injector calibration code programmed into the ECM for Cylinder 4
Connect scan tool live telemetry: compare Target Fuel Rail Pressure vs Actual Rail Pressure and log metering valve command PWM duty cycle during idle and road load.
Expensive Diagnostic Pitfall & Technical Reality
P0272 means Cylinder 4 has blown a head gasket or scored cylinder walls, requiring an engine overhaul ($3,000 - $5,500).
Cylinder 4 operates at the highest thermal ambient temperature in the engine bay. In over 80% of verified cases, mechanical compression is normal. P0272 is triggered when the ECM's smooth running trim exceeds +4.5 mg/stroke attempting to balance Cylinder 4. The true cause is typically carbon coking plugging the micro-orifices of the injector nozzle tip, an eroded copper combustion washer blowing compression gas into the injector well, or a sticking hydraulic command valve.
Unnecessary engine teardown ($3,500+) vs ultrasonic nozzle cleaning or replacing the $3 copper crush washer, saving over $3,000.
Moteurs et plateformes d'injection les plus touchés
Ce code défaut affecte principalement les plates-formes diesel à rampe commune suivantes. Consultez votre famille de moteurs pour les causes de panne et références de pièces associées :
Ford / PSA 1.6 TDCi / HDi (DV6ATED4 / DLD-416)
Bosch CRI2-16 Common Rail SystemMode de défaillance constructeur : Injector copper washer blow-by (black death), injector cylinder circuit fretting corrosion, DPF pressure pipes heat cracking.
0445110239, 1980J7, 1618LPVolkswagen / Audi 2.0 TDI (EA189 / CFFB / CFGB)
Bosch EDC17 Common Rail SystemMode de défaillance constructeur : Piezo stack degradation, injector harness terminal fretting, DPF differential pressure sensor silicone tube split.
03L130277, 0445110369, 076906051ARenault / Opel 1.9 dCi (F9Q)
Bosch EDC15 / EDC16 Common Rail SystemMode de défaillance constructeur : Injector harness connector diesel seepage, glow plug tip carbon seizure, EGR valve soot accumulation.
7700107165, 0445110021, 8200542997BMW 2.0d / 3.0d (N47 / N57 / M57TU2)
Bosch CRI2.5 / CRI3.0 Common RailMode de défaillance constructeur : Injector balance drift beyond +/- 4.0 mg/stroke, glow plug control unit (BERU) power lead failure, DPF backpressure accumulation.
13537805428, 0445116024, 12217801201Cylinder Balance & Injector Deviation Guide
Common rail diesel cylinder balance & smooth running diagnostic guide. Balance rates, mg/stroke deviation, P0263 misfire, compression vs injector test.
Circuit de commande & Logique d'actionneur
1. Dynamic In-Demand Fuel Metering
Modern common rail diesel engines operate without a physical distributor or mechanical governor; cylinder-to-cylinder torque equalization is performed purely through software. The ECM monitors flywheel tooth passage times using a high-precision magnetic or Hall-effect CKP sensor reading a 60-2 or 36-2 target wheel. If Cylinder 4 produces less power due to a partially coked injector nozzle, excessive internal hydraulic backleak, or slightly degraded mechanical compression, the crankshaft slows down momentarily during Cylinder 4's power segment. The ECM immediately compensates by extending the injection duration for Cylinder 4.
2. Closed-Loop PID Deviation Monitoring
The Smooth Running Control (SRC) algorithm calculates a real-time fuel trim offset for each cylinder (displayed in scan tools as 'Cylinder Balance Rate' or 'Injector Quantity Offset', typically scaled in mg/stroke or mm³/stroke). A healthy cylinder operates between -1.5 mg/stroke and +1.5 mg/stroke. When Cylinder 4's required fuel correction exceeds calibrated upper limits (+3.5 to +6.0 mg/stroke) for longer than 500 consecutive combustion cycles at warm idle, or during an automated cylinder cutout diagnostic sweep, the ECM flags P0272 and locks the balance rate into freeze frame memory.
3. Diagnostic Trap: Normally Open (NO) vs Normally Closed (NC) Valves
Contribution Fault (P0272) vs Misfire (P0304) Diagnostic Distinction: Technicians frequently confuse these two codes. P0304 indicates a COMPLETE combustion failure (misfire/dead miss, zero flame propagation), usually caused by an electrical open circuit, completely blocked injector, or zero compression. In contrast, P0272 indicates PARTIAL combustion: fuel is injecting and igniting, but the kinetic energy delivered is suboptimal compared to companion cylinders. In over 75% of diesel cases, P0272 is caused by mechanical injector nozzle varnish or excessive control valve return leakage, NOT electrical circuit failure.
Valeurs de référence électriques & hydrauliques
Protocole de Diagnostic Atelier pas à pas
Live Scan Tool Cylinder Balance Rate (SRC) Logging
Warm the engine until coolant temperature exceeds 80°C (176°F). Access scan tool live data for 'Cylinder Balancing / Smooth Running Control'. Observe the real-time fuel trim for all cylinders at stable idle (A/C off, transmission in park/neutral). Normal values are -1.5 to +1.5 mg/stroke. If Cylinder 4 reads +3.5 to +5.5 mg/stroke, the ECM is struggling to add massive fuel to compensate for a weak Cylinder 4 power stroke.
Automated Cylinder Cutout RPM Drop Test
Using scan tool bi-directional controls, perform an automated 'Cylinder Cutout Test'. The ECM will disable fuel injection to each cylinder sequentially. On a healthy cylinder, shutting off injection causes a sharp 45 to 65 RPM drop and noticeable engine stumble. If cutting out Cylinder 4 produces less than a 20 RPM drop, it proves Cylinder 4 was barely contributing power before being cut.
Individual Injector Backleak (Return Flow) Measurement
Disconnect the low-pressure fuel return line from all injectors. Attach graduated transparent test tubes to the return nipples. Start the engine and run at warm idle for exactly 2 minutes. Measure return volume in milliliters. A healthy injector returns less than 20-25 mL. If Cylinder 4 returns >40 mL, its internal hydraulic control valve seat is eroded, dumping rail pressure into the return.
Electronic Relative Compression & Mechanical Gauge Test
Execute an electronic 'Relative Compression Test' via scan tool, which monitors starter current draw across each compression stroke. All cylinders must match within 95% to 100%. If Cylinder 4 shows <85%, remove the glow plug and perform a physical mechanical compression gauge test (must exceed 22 bar with <3 bar variance). Low compression confirms a valve, ring, or head gasket issue.
Injector Cross-Swap Physical Verification
To conclusively isolate the injector from engine mechanics, remove the Cylinder 4 injector and swap it with Cylinder 1 (using new copper washers). Reprogram the respective IMA/QR codes into the ECM. Clear DTCs and road-test the vehicle. If the fault moves from P0272 to P0263 (Cylinder 1), the injector is 100% defective. If the fault stays on P0272 on Cylinder 4, the cause is mechanical compression or valvetrain wear.
IMA / QR Calibration Code Verification
Read the physical 6-to-30 digit alphanumeric code laser-etched onto the top plastic head of the Cylinder 4 injector. Compare this code against the code stored in the ECM memory using your scan tool. If an uncalibrated replacement injector was installed without programming, the ECM uses generic default pulse widths that can cause a 15% to 20% fueling error, triggering P0272.
Réparation matérielle & Nomenclature sous-ensembles
Cylinder 4 Fuel Metering Calibration & IMA Coding Architecture
0 445 110 369 / 0 445 116 059
High-precision electro-hydraulic fuel injector with laser-etched IMA calibration classification code
F 00V C17 503 / OEM Copper Crush Washer
Gas-tight sealing ring preventing combustion gas leakage that drops effective cylinder compression
DLLA 150 P 1828 / OEM Nozzle Assembly
Atomizes high-pressure diesel into micro-droplets; clogged micro-holes reduce cylinder contribution
Calculateur dynamique de tolérances Common Rail
Composants d'injection associés
Les pompes à carburant et injecteurs à rampe commune d'origine suivants sont vérifiés pour les moteurs signalant le code P0272. Vérifiez les pressions de service avant le remplacement :
0445110021BOSCH
BOSCH 0445110021 - F9Q 1.9 dCi Common Rail Injector
View Technical Specs & Fitment →0445110239BOSCH
0445110239 Injector: PSA 1.6 HDi Ford 1.6 TDCi Specs
View Technical Specs & Fitment →0445110369BOSCH
0445110369 Injector: VW 2.0 TDI EA189 CFFB CFHC Specs
View Technical Specs & Fitment →0445116024BOSCH
BOSCH 0445116024 Common Rail Piezo Injector for BMW N47 2.0d & N57 3.0d
View Technical Specs & Fitment →095000-5880Denso
095000-5880 Denso Toyota 2KD-FTV Injector: 23670-30050 Data
View Technical Specs & Fitment →28337917Delphi
28337917 Delphi Bobcat D24 Injector: 7030364 Specs & Data
View Technical Specs & Fitment →Réinitialisation de la pompe HP & Cycle d'apprentissage
Following replacement of the Cylinder 4 fuel injector, nozzle servicing, or valve adjustment, execute the adaptation routine:
1. Enter the new alphanumeric calibration code (IMA/QR code) stamped on the new Cylinder 4 injector into the ECM via scan tool.
2. Clear all stored trouble codes and confirm engine coolant temperature is above 75°C (167°F).
3. Access scan tool 'Engine Control Module' -> 'Special Functions' -> select 'Reset Cylinder Balance / Smooth Running Values'.
4. Start the engine and allow it to idle undisturbed in park/neutral for 5 minutes without touching any pedals, allowing the ECM to build initial torque offsets.
5. Accelerate vehicle smoothly in 4th gear to 80 km/h (2200 RPM), then release throttle completely to coast down in gear to 35 km/h (minimum 8s overrun).
6. Repeat this acceleration and coast-down sequence 5 times. Return to workshop and confirm Cylinder 4 balance rate is within ±1.5 mg/stroke.
Diagnostic différentiel & Codes associés
Cylinder 4 Misfire Detected
Hard misfire code indicating complete lack of combustion on Cylinder 4, whereas P0272 indicates combustion occurs but with degraded power delivery.
Injector Circuit/Open - Cylinder 4
Electrical circuit fault code on Cylinder 4; if an injector wiring fault develops, P0204 will trigger alongside or override P0272.
Cylinder 1 Contribution/Balance Fault
Companion code on Cylinder 1; swapping injectors between Cylinders 4 and 1 allows immediate isolation of injector hardware vs cylinder mechanics.
Cas pratiques d'atelier
2015 Mercedes-Benz E220 CDI (W212 OM651)(189,000 km)
Questions techniques fréquentes
Que signifie le code défaut P0272 ?
Le code défaut P0272 indique que le calculateur de gestion moteur a détecté que le cylindre 4 ne fournit pas l'impulsion de couple mécanique théorique au vilebrequin, générant un déséquilibre de rotation inter-cylindres (défaut d'acyclisme). Sur les moteurs diesel à rampe commune, le calculateur calcule en continu le travail individuel de chaque cylindre en mesurant les micro-variations de l'accélération angulaire via le capteur de position vilebrequin (capteur PMH) durant la phase de détente, entre 30° - 90° après le point mort haut (PMH). Si l'algorithme de régulation de circularité / correction de débit applique une compensation excessive (typiquement supérieure à +3,0 - +4,5 mg/coup) pour stabiliser le ralenti, ou si la contribution chute de 15% - 25% sous la moyenne moteur, le code P0272 est enregistré.
Quels sont les symptômes les plus fréquents de P0272 ?
Noticeable engine shudder, rough idle, and cabin vibration during warm idle (especially in Drive at traffic lights), Hesitation, flat spots, or rhythmic surging during light-to-moderate throttle cruising at 1200 to 2000 RPM, Check Engine Light (MIL) illuminated, occasionally accompanied by flashing glow plug light or traction control warning, Heavy puffing of grey or black exhaust smoke on sudden acceleration due to unburned fuel in Cylinder 4, Elevated fuel consumption and rough engine shutdown (excessive diesel shudder when turning off the ignition), Scan tool live data displays Cylinder 4 balance rate pegged at high positive compensation (+3.5 to +5.5 mg/stroke).
Quelles sont les causes de P0272 sur un diesel ?
Partially clogged, carbon-coked, or eroded spray holes in the Cylinder 4 fuel injector nozzle tip; Excessive internal control valve wear (backleak) in Cylinder 4 injector, reducing effective injection pressure and fuel delivery; Incorrect, corrupted, or uncalibrated IMA / QR injector calibration code programmed into the ECM for Cylinder 4; Low mechanical cylinder compression on Cylinder 4 caused by worn piston rings, valve seat recession, or blown head gasket (Cyl 4 runs hottest near firewall); Cylinder 4 glow plug tip coated in thick carbon or burned out, impairing post-start combustion stability in cold engines; Worn camshaft lobe or collapsed hydraulic lifter reducing intake valve lift and starving Cylinder 4 of fresh air charge.
Est-il prudent de rouler avec le code P0272 actif ?
🟡 Attention : Mode dégradé actif / Réparation requise
Combien coûte la réparation du code défaut P0272 ?
Le coût moyen de réparation du code défaut P0272 dépend de la cause racine et du niveau de diagnostic : Niveau 1 (Entretien mineur / DIY) : 40 € - 110 € : Remplacement du filtre à carburant premium et nettoyage des injecteurs diesel (Nettoyage de capteur, remplacement du filtre à carburant, contrôle de fusible ou des connecteurs.); Niveau 2 (Remplacement composant) : 180 € - 480 € : Remplacement de l'injecteur Common Rail d'origine du cylindre 4 (Remplacement d’un composant (régulateur de pression, vanne de dosage ou injecteur reconditionné).); Niveau 3 (Sous-ensemble complet) : 850 € - 2 200 € : Contrôle des compressions mécaniques ou inspection de l'usure des cames d'arbre à cames (Révision de pompe haute pression, jeu d’injecteurs neufs ou remplacement de l’ensemble FAP.). Tarifs indicatifs d’atelier. Les données indiquent que plus de 70% des cas sont résolus aux niveaux 1 ou 2 sans remplacer les sous-ensembles complets.
Can a fuel additive or injector cleaner fix trouble code P0272?
In mild, early-stage cases where P0272 is caused by soft gummy diesel varnish or light carbon deposits on the injector nozzle spray holes, a professional-grade polyetheramine (PEA) or cetane-boosting diesel injector cleaner run through a concentrated dose can dissolve deposits and restore balance rates within 50 to 100 miles. However, if the cause is mechanical control valve erosion (excessive backleak) or low mechanical cylinder compression, chemical additives will have zero effect and the injector must be replaced.
Why does Cylinder 4 suffer from contribution faults more often than other cylinders?
On transverse and longitudinal 4-cylinder diesel engines, Cylinder 4 is situated at the very back of the engine block against the firewall. This location receives the least airflow, has the hottest coolant outlet temperatures, and experiences the greatest heat soak. Over hundreds of thousands of miles, higher operating temperatures accelerate injector nozzle varnish baking, valve guide wear, and piston ring fatigue.
Is trouble code P0272 safe to drive with?
You can drive short distances to reach a repair facility, but prolonged driving is not recommended. If the contribution fault is caused by an injector nozzle with a bad spray pattern (dripping rather than atomizing), liquid diesel will pool on the piston crown, risking severe piston melting and engine failure under highway loads. Furthermore, incomplete combustion creates high soot levels that will rapidly clog your DPF filter.