DL3Z-9F593-A
BOSCH DL3Z-9F593-A Direkt Enjektör Ford F-150 3.5L EcoBoost V6
0261500140, 0261500141, FJ1151High-Response Multi-Hole Electromagnetic High-Pressure Nozzle-150 barTeknik Özellikler
| Özellik | Değer |
|---|---|
| Sistem Tipi | Ford EcoBoost 150-bar High-Pressure Direct Injection System |
| Çalışma BasıncıTemel Değer | |
| Spray Configuration | Laser-Drilled 6-Hole Asymmetric Spray Pattern |
| INJECTOR HOLD-DOWN BOLT TORQUE | 10 N·m (89 in-lb) fuel rail mounting bolts📐 Tork ve Açı Sihirbazı → |
| FUEL LINE NUT TORQUE | 28 N·m (21 lb-ft) high-pressure crossover tube flare nut |
| Combustion Seal | PTFE Virgin Teflon Combustion Ring with Backing Washer |
| Rail Sealing | High-Temperature Fluorocarbon (FKM) Upper O-Ring |
| Manufacturer | Bosch (Tier-1 OEM for Ford Motor Company) |
| Bosch Production Number | 0261500140 / 0261500141 |
Uyumlu Yüksek Basınç Pompası (Yakıt Devresi Grubu)
Aynı yüksek basınçlı Common Rail devresinde çalışır. Düşük basınç (P0087) teşhisinde enjektörleri değiştirmeden önce pompa debisini kontrol edin.
Montaj İpuçları
- [
- {
- "step": 1,
- "title": "EcoBoost High-Pressure Fuel Rail Depressurization",
- "instruction": "Depressurize fuel system by removing the low-pressure fuel pump fuse and running engine until it dies. Disconnect negative battery cable."
- },
- {
- "step": 2,
- "title": "Upper Intake Manifold & Charge Pipes Removal",
- "instruction": "Disconnect turbo boost pipes, throttle body wiring, PCV hoses, and remove the composite upper intake plenum to access Bank 1 and Bank 2 fuel rails."
- },
- {
- "step": 3,
- "title": "High-Pressure Crossover Pipe Disconnection",
- "instruction": "Unscrew the stainless steel high-pressure fuel crossover lines using a 17mm flare nut wrench. Discard the single-use hard pipes per Ford service directives."
- },
- {
- "step": 4,
- "title": "Fuel Rail Extraction & Bore Prep",
- "instruction": "Remove fuel rail retaining bolts. Pull rails and injectors straight back along their axis. Thoroughly clean carbon deposits from the cylinder head injector wells."
- },
- {
- "step": 5,
- "title": "Injector Installation & Final Torquing",
- "instruction": "Lubricate upper O-rings with clean engine oil (keep Teflon tips completely dry). Push injectors into rail, torque rail bolts to 10 N·m (89 in-lb), and crossover pipe nuts to 28 N·m (21 lb-ft)."
- }
- ]
Ariza Kodlari (DTC) ve Teshis Protokolleri
Bu common rail enjektorunde asinma, devre arizasi veya kalibrasyon kaymasi olustugunda tetiklenen yaygin ariza kodlari (DTC):
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Teknik Arıza Teşhis ve Servis Protokolleri
Bu parça grubu için doğrulanmış atölye prosedürleri, test eşik değerleri ve servis talimatları.