BOSCH
JR3Z-9F593-A
Technische Daten
SolenoidGasoline Direct Injection (GDI)Euro 56
BOSCH JR3Z-9F593-A Einspritzventil Ford Mustang GT F-150 5.0L Coyote V8 0261500412
Motorenplattform:Ford 5.0L Coyote V8 (Gen 3 PFDI Dual-Fuel Ti-VCT) →
OE-REFERENZ
JR3Z-9F593-B, 0261500413, CM5278STEUERVENTIL
-EINSPRITZDÜSE
-BETRIEBSDRUCK
200 barABGASNORMEuro 5 / Euro 6
GARANTIE12 Monate
03
Technische Daten
| Spezifikation | Wert |
|---|---|
| Part Number / SKU | JR3Z-9F593-A |
| Manufacturer Brand | BOSCH |
| Component Type | Direct Fuel Injector |
| Engine Application | Ford 5.0L Coyote Ti-VCT Dual-Fuel DOHC 32V V8 (Gen 3 Coyote) |
| BetriebsdruckKernwert | |
| Mounting Torque (Flange / Bracket) | 10 N-m (89 lb-in) |
| Fuel Line / Rail Torque | 22 N-m (16 lb-ft) |
| Typische Fehlercodes | P0300, P0301, P0171, P0172 |
04
Einbauhinweise
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 10 N-m (89 lb-in), and torque fuel line fittings to 22 N-m (16 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
05
Fehlercodes (DTC) & Diagnoseprotokolle
Häufige Diagnose-Fehlercodes (DTCs), die ausgelöst werden, wenn dieser Common-Rail-Injektor Verschleiß, Schaltkreisfehler oder Kalibrierungsabweichungen aufweist:
P0087Critical
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
P0201 - P0208High
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
P0300 / P0301+High
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
P0088High
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
WERKSTATT-LEITFÄDEN
Technische Diagnose- & Service-Protokolle
Verifizierte Prüfverfahren, Fehlercode-Grenzwerte und Werkstatt-SOPs für diese Baugruppe.
COMMON-RAIL WERKSTATT-DIAGNOSE
Technischen Leitfaden lesenZumesseinheit ZME IMV SCV Diagnose: P0088 Fehlertest
OBD-II-DIAGNOSEPROTOKOLL
Technischen Leitfaden lesenDiagnoseleitfaden P0087: Raildruck zu niedrig
DIESEL-WERKSTATT DIAGNOSE-SOP
Technischen Leitfaden lesenLaufruheregelung & Injektor-Mengenkorrektur Diagnose
MONTAGE- UND EINBAUPROTOKOLL
Technischen Leitfaden lesen