BOSCH
JR3Z-9F593-A
Visa spec.
SolenoidGasoline Direct Injection (GDI)Euro 56
BOSCH JR3Z-9F593-A Bränsleinjektor Ford Mustang GT F-150 5.0L Coyote V8
Motorplattform:Ford 5.0L Coyote V8 (Gen 3 PFDI Dual-Fuel Ti-VCT) →
OE-REFERENS
JR3Z-9F593-B, 0261500413, CM5278STYRVENTIL
-SPRIDARSPETS
-RAILTRYCK
200 barMILJÖKLASSEuro 5 / Euro 6
GARANTI12 Månader
03
Tekniska specifikationer
| Specifikation | Värde |
|---|---|
| Part Number / SKU | JR3Z-9F593-A |
| Manufacturer Brand | BOSCH |
| Component Type | Direct Fuel Injector |
| Engine Application | Ford 5.0L Coyote Ti-VCT Dual-Fuel DOHC 32V V8 (Gen 3 Coyote) |
| ArbetstryckHuvudspec. | |
| Mounting Torque (Flange / Bracket) | 10 N-m (89 lb-in) |
| Fuel Line / Rail Torque | 22 N-m (16 lb-ft) |
| Vanliga felkoder | P0300, P0301, P0171, P0172 |
04
Monteringsanvisningar
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 10 N-m (89 lb-in), and torque fuel line fittings to 22 N-m (16 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
05
Felkoder (DTC) och Diagnosprotokoll
Vanliga diagnosfelkoder (DTC) som aktiveras nar denna common rail-injektor uppvisar slitage, kretsfel eller kalibreringsavvikelse:
P0087Critical
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
P0201 - P0208High
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
P0300 / P0301+High
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
P0088High
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
VERKSTADSMANUALER
Tekniska Diagnos- och Serviceprotokoll
Verifierade verkstadsrutiner, testgränsvärden och serviceinstruktioner för denna komponent.
COMMON RAIL VERKSTADSDIAGNOSTIK
Läs tekniskt protokollBränsledoseringsventil IMV SCV Diagnos: P0088 Test
OBD-II DIAGNOSPROTOKOLL
Läs tekniskt protokollP0087 Lågt railtryck - Diagnos- och felsökningsguide
DIESELVERKSTADENS DIAGNOS-SOP
Läs tekniskt protokollCylinderbalans & spridaravvikelse: Teknisk diagnosguide
MONTERINGS- OCH INSTALLATIONSPROTOKOLL
Läs tekniskt protokoll