P2002: Filtro de partículas diésel (DPF) - Eficiencia por debajo del umbral (Banco 1)
La centralita detecta una eficacia de filtrado insuficiente en el DPF del banco 1. Frecuentemente provocado por un monolito cerámico roto o manguitos de presión diferencial derretidos.
🚗 Seguridad operativa, presupuesto estimado y verificación
- 01
🚦 Seguridad de conducción y riesgo mecánico
Evaluación mecánica inmediata y necesidad de grúaEficiencia DPF reducida - Cerámica agrietada o tubos de presión quemados
La ECU detecta una presión diferencial anómala. Con frecuencia la cerámica del DPF se ha roto o los tubos de silicona se han fundido con el calor del turbo. Se puede circular temporalmente, pero aumentará el hollín en el escape.
PELIGROS MECÁNICOS SI CONTINÚA CONDUCIENDO:¡Nunca intente una regeneración forzada con el código P2002! Si el filtro está agrietado, el gasóleo inyectado inflamará el hollín en las grietas fundiendo la cerámica (>1.000°C), con alto riesgo de incendio bajo el coche. - 02
💰 Presupuesto típico de taller
Niveles de costo esperados para repuestos y mano de obraMantenimiento menor / Filtro30 € - 80 €: Sustitución de tubos de silicona del sensor diferencial / limpieza de tomasLimpieza de sensor, cambio de filtro de combustible, revisión de fusibles o conectores.
Cambio de válvula / Sensor120 € - 260 €: Cambio de sensor de presión diferencial (DPS) y calibración de punto ceroSustitución de componente individual (válvula reguladora, unidad dosificadora o inyector reconstruido).
Reparación mayor / Bomba e inyectores1.200 € - 2.800 €: Sustitución del filtro DPF OEM en caso de rotura interna de la cerámicaRevisión de bomba de alta presión, juego de inyectores nuevos o sustitución del conjunto DPF.
- 03
🧰 Verificaciones visuales rápidas en garaje
Chequeo de 5 minutos sin herramientas antes de ir al taller1Prueba del pañuelo blanco en el escape: frote el interior de la cola de escape; hollín negro abundante confirma que la cerámica del DPF está rota.2Revisar tubos del sensor diferencial: comprobar si los manguitos de goma hacia el sensor en el cortafuegos están rajados o derretidos.3Comprobar el punto cero del sensor con contacto puesto: el valor con motor parado debe ser de 0,0 ± 2,0 mbar.4Comprobar el nivel de aceite motor: verificar que no haya subido por dilución de gasóleo tras regeneraciones abortadas. - 04
🛡️ Protección ante diagnósticos erróneos en taller
Preguntas técnicas exactas para evitar sustituciones de piezas innecesarias"Diga al taller: 'Revisen los tubos del sensor diferencial y el voltaje de reposo (0,50 V) antes de condenar el filtro DPF.'"
"Diga al taller: 'No fuercen una regeneración si sospechan que la cerámica está rota, hay riesgo de incendio.'"
"Diga al taller: 'Comprueben el sobrante de inyectores para descartar inyectores que gotean y dañan el DPF.'"
Nota técnica: Haga estas preguntas técnicas a su mecánico antes de autorizar presupuestos caros:
Triaje de taller en 30 segundos
- Velvety black soot deposits coating the inside tip of the vehicle exhaust tailpipe (the ultimate physical confirmation of substrate failure)
- Illuminated Check Engine Light (MIL) accompanied by flashing DPF warning light on the instrument cluster
- Vehicle enters Limp-Home Mode with severe torque limitation and engine RPM ceiling derate
- Thermally cracked, melted, or fragmented DPF ceramic monolith caused by uncontrolled regeneration fire (>1000°C)
- Defective DPF Differential Pressure Sensor (DPS) reporting false low delta-P due to internal silicon sensor drift
- Cracked, severed, or melted silicone/rubber pressure sensing sample lines connecting exhaust pipes to the differential sensor
Connect scan tool live telemetry: compare Target Fuel Rail Pressure vs Actual Rail Pressure and log metering valve command PWM duty cycle during idle and road load.
The $2,500 DPF Replacement Trap: Melted Differential Pressure Sensing Hoses vs Destroying a New DPF with Leaking Injectors
When P2002 (DPF Efficiency Below Threshold) is stored, repair facilities frequently jump to condemning the entire exhaust aftertreatment system, charging $2,200 to $3,800 for a new DPF canister without inspecting the pressure sensing lines or testing injector spray atomization.
In many modern diesels, P2002 is triggered by a simple $15 split or thermal melting on the rubber differential pressure pickup hose near the turbocharger heat shield: exhaust pressure vents to atmosphere before reaching the sensor, tricking the ECM into reading near-zero delta-P and concluding the DPF substrate has collapsed. Even more crucially, if the DPF ceramic substrate really DID crack or melt, it was torched by upstream leaking fuel injectors dumping raw diesel into the exhaust during 600°C regeneration. Installing a new DPF without fixing the dripping injectors will melt the replacement filter within 1,000 miles.
First, perform the 'White Glove Tailpipe Test': wipe the exhaust tip. If clean, the DPF substrate is intact; inspect the rubber differential sensor hoses for splits and verify Key-ON sensor zero-point voltage reads exactly 0.50V ± 0.05V. If the tailpipe is coated with heavy black soot, the substrate is definitely broken; before installing a new filter, perform a dynamic injector backleak test on all cylinders to isolate and replace any leaking injector nozzles that caused the thermal meltdown.
Motores y plataformas de inyección más afectados
Este código de error afecta principalmente a las siguientes plataformas diésel common rail. Consulte su familia de motores para ver fallos típicos y referencias de piezas:
VAG 2.0 TDI EA189 / EA288 (VW Golf, Passat, Audi A4, Skoda)
Bosch EDC17 DPF SystemSíntoma típico: DPF warning lamp and flashing glow plug, tailpipe blackened with velvety soot, code P2002 stored.
Fallo típico de fábrica: Differential pressure sensor (G450) internal semiconductor drift; ceramic honeycomb internal micro-fissuring.
076906051A / 04L906051Ford Transit Custom / Focus 2.0 EcoBlue (Panther)
Continental / Bosch DPFSíntoma típico: Power loss, service emissions message, black soot coating rear bumper and tailpipe.
Fallo típico de fábrica: Vaporizer fuel injector (glow-plug style fuel doser) clogged by carbon, preventing exhaust thermal rise for regeneration.
2038753 / 1876800Mercedes-Benz 2.1 CDI OM651 (C220, E220, Sprinter)
Delphi / Bosch DPFSíntoma típico: Vehicle enters limp-home mode, DPF light illuminated, high exhaust backpressure under load.
Fallo típico de fábrica: Differential pressure silicone pipes melt from turbo radiant heat; upstream injector over-fuelling soot loading.
A0061539528 / A6519050200BMW 2.0d N47 / 3.0d N57 (X3, X5, 320d, 520d)
Bosch DPF SystemSíntoma típico: Drivetrain malfunction on iDrive, soot buildup in tailpipe, frequent aborted regeneration cycles.
Fallo típico de fábrica: Coolant thermostat stuck open (<75°C engine temp prevents DPF regen cycle from starting); glow plug control module fault.
13627805152 / 11517805811Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB
Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.
Circuito de control y lógica del actuador
1. Dynamic In-Demand Fuel Metering
The Diesel Particulate Filter (DPF) consists of a ceramic wall-flow honeycomb monolith constructed from Cordierite or Silicon Carbide (SiC). Parallel microscopic channels are alternately plugged at opposite ends: exhaust gas is forced through the porous ceramic channel walls, trapping soot particles within the filter pores while allowing gaseous exhaust to escape. A high-temperature catalytic coating (DOC/DPF) promotes passive regeneration by converting NO to NO2 at temperatures between 250°C and 450°C. When accumulated soot reaches 20 to 30 grams, the ECM initiates active thermal regeneration by commanding post-injection fuel delivery to elevate exhaust gas temperatures to 580°C-650°C, incinerating trapped carbon into microscopic ash.
2. Closed-Loop PID Deviation Monitoring
The ECM monitors DPF Differential Pressure via a dual-port piezo-resistive pressure sensor plumbed upstream and downstream of the filter. The ECM's internal software maintains two parallel soot trackers: a 'Measured Soot Load' (calculated directly from differential pressure and volumetric exhaust flow rate) and a 'Calculated Soot Load' (estimated from engine runtime, fuel consumption, speed, and MAF air mass). If the calculated soot model indicates high soot accumulation while the physical differential pressure sensor reports near-zero delta-P (e.g., <15 mbar at 3000 RPM full load), the ECM determines that the ceramic core has fractured or melted, setting P2002.
3. Diagnostic Trap: Normally Open (NO) vs Normally Closed (NC) Valves
Crucial Workshop Distinction: Blocked DPF (P2463/P2458) vs Melted/Cracked DPF (P2002): Technicians frequently confuse P2002 with DPF clogging codes. P2463 indicates the filter is OVERLOADED with soot (>40g) and differential pressure is dangerously high (>250 mbar). In stark contrast, P2002 indicates the filter is LEAKING soot: the ceramic substrate has suffered thermal cracking or core wash-out, allowing exhaust soot to blow straight through. Cleaning an existing DPF with P2002 is 100% futile because the physical filter substrate is broken.
Valores físicos eléctricos e hidráulicos
Protocolo de Diagnóstico de Taller Paso a Paso
Physical Tailpipe Soot Wipe & Substrate Borescope Inspection
Wipe a clean white cloth or gloved finger inside the vehicle's exhaust tailpipe tip. If heavy black soot transfers to the cloth, the DPF ceramic monolith is mechanically compromised and cannot be saved by chemical cleaning or forced regeneration. Remove the downstream exhaust gas temperature sensor or NOx sensor and insert a flexible HD borescope camera to inspect the outlet face of the DPF ceramic core for cracks, melted cell channels, or missing sections.
Differential Pressure Sensor Zero-Point Key-ON Offset Calibration
With the engine off and key in ON position, read live scan tool data for 'DPF Differential Pressure'. A healthy, un-skewed sensor must report exactly 0.0 mbar ± 2.0 mbar (0.50 V ± 0.05 V). If the sensor reads -15 mbar or +20 mbar with zero exhaust flow, the sensor's internal piezoresistive element has drifted and the sensor must be replaced.
Pneumatic Inspection of Stainless Steel Differential Pressure Sample Tubes
Inspect the metal pressure pickup pipes leading from the front and rear of the DPF cannister to the differential pressure sensor. Check for cracks, corrosion holes, or melted rubber union hoses. Disconnect the rubber hoses at the sensor end and use a hand pressure bulb to gently blow compressed air back through the pipes into the exhaust. Both lines must flow completely freely without carbon blockage.
Live Differential Pressure Logging Under WOT Loaded Acceleration
Conduct a live road test while logging 'Engine RPM', 'Exhaust Gas Temperature (EGT 1/2/3)', and 'DPF Differential Pressure'. At idle, differential pressure should be 3-12 mbar. Under a hard 3rd-gear acceleration up to 3500 RPM (WOT), differential pressure must rise smoothly to 80-180 mbar. If differential pressure remains below 25 mbar under maximum exhaust volume, the DPF substrate is hollowed out or severely cracked.
Fuel Injector Hydraulic Backleak & Cylinder Balance Verification
Before replacing a cracked DPF, perform an injector return leakage flow test (Backleak Test) across all cylinders. A leaking injector needle or worn control valve dumps raw fuel that puddles inside the DPF; when active regeneration triggers, this raw fuel creates an intense localized torch fire that thermal-shocks and cracks the ceramic honeycomb.
Exhaust Gas Temperature (EGT) Sensor Plausibility Check
Before starting a cold engine (left overnight), compare all exhaust gas temperature sensors (DOC Inlet, DPF Inlet, DPF Outlet, SCR Catalyst). All EGT sensor readings must agree within ±5°C of ambient temperature. A failing EGT sensor reading artificially low will cause the ECM to command excessive post-injection fuel, leading to thermal DPF meltdown.
Reparación de hardware y lista de piezas BOM
Isolate sensing lines and upstream combustion causes before purchasing a costly complete DPF assembly using verified OEM/Tier-1 part numbers:
0281006082 / 076906051ABosch / VAG
High-precision dual-port piezoresistive exhaust differential pressure transducer (0-100 kPa / 0.5-4.5V output).
DPS-HOSE-HD6FuelPartsDB Engineering
Reinforced 6.0 mm internal diameter fluorosilicone tubing with fiberglass thermal heat sleeve rated to 350°C.
0281004148 / 03L906088BSBosch / NTK
PT200 platinum resistance high-temperature sensor monitoring regeneration furnace temperatures upstream of the DPF.
DLLA153P1608 / DLLA148P1641Bosch
Micro-precision multi-hole injector nozzle tip preventing post-injection fuel dribble and uncontrolled regeneration fires.
Calculadora interactiva de tolerancias Common Rail
Reinicio de adaptación de bomba y ciclo de rodaje
Whenever a DPF filter or Differential Pressure Sensor (DPS) is replaced, the ECM's internal ash and soot counters must be zeroed:
1. Connect scan tool and navigate to 'Engine Management' -> 'Component Adaptations' / 'Special Functions'.
2. Select 'Initialize / Relearn Differential Pressure Sensor' with Key-ON Engine-OFF to zero-calibrate baseline voltage.
3. Select 'Reset Diesel Particulate Filter (DPF) Learned Values' -> choose 'New Filter Installed' (sets Soot Mass to 0.0g and Oil Ash Volume to 0.0L).
4. Start engine and verify at idle that Differential Pressure reads between 3.0 mbar and 10.0 mbar.
5. Conduct a 20-minute highway drive cycle at 100 km/h (60 mph) to allow the ECM to build initial speed-density baseline curves.
6. Inspect exhaust tailpipe: verify it remains 100% clean and confirm DPF status flags show 'Normal / System OK'.
Diagnóstico diferencial y códigos relacionados
Diesel Particulate Filter - Soot Accumulation
Opposite condition where the DPF is severely clogged with excessive soot (>40g) and differential backpressure is dangerously high, unlike P2002 where the substrate is leaking soot.
DPF Differential Pressure Sensor 'A' Circuit
Hard electrical fault on the pressure sensor wiring (open circuit, short to power, or short to ground) rather than an aerodynamic filter core failure.
Diesel Particulate Filter Regeneration Duration
Accompanies P2002 when the ECM repeatedly initiates thermal regeneration but fails to satisfy soot reduction models because the substrate cannot retain temperature.
Casos reales de taller
Preguntas técnicas frecuentes
¿Qué significa el código de fallo P2002?
La centralita detecta una eficacia de filtrado insuficiente en el DPF del banco 1. Frecuentemente provocado por un monolito cerámico roto o manguitos de presión diferencial derretidos.
¿Cuáles son los síntomas más comunes de P2002?
Velvety black soot deposits coating the inside tip of the vehicle exhaust tailpipe (the ultimate physical confirmation of substrate failure), Illuminated Check Engine Light (MIL) accompanied by flashing DPF warning light on the instrument cluster, Vehicle enters Limp-Home Mode with severe torque limitation and engine RPM ceiling derate, Foul, acrid exhaust odor resembling raw diesel smoke or unburned hydrocarbons during driving, Increased frequency of active regeneration attempts as the ECM struggles to clear phantom soot calculations, Elevated engine oil level (oil dilution) caused by excessive post-injection diesel fuel leaking past piston rings during failed regenerations.
¿Qué causa P2002 en un motor diésel?
Thermally cracked, melted, or fragmented DPF ceramic monolith caused by uncontrolled regeneration fire (>1000°C); Defective DPF Differential Pressure Sensor (DPS) reporting false low delta-P due to internal silicon sensor drift; Cracked, severed, or melted silicone/rubber pressure sensing sample lines connecting exhaust pipes to the differential sensor; Soot or water condensation freezing inside differential pressure metal sensing tubes, blocking pressure transfer; Upstream leaking fuel injectors delivering excessive unburned diesel that ignites inside the DPF during thermal regeneration; Defective downstream Exhaust Particulate Matter (PM) sensor transmitting false high-soot concentration error signals to the ECM.
¿Es seguro conducir con el código P2002 activo?
🟡 Precaución: Modo emergencia activo / Acudir a taller
¿Cuánto cuesta reparar el código de avería P2002?
Los costes habituales de reparación para P2002 dependen de la causa raíz identificada en el diagnóstico: Nivel 1 (Mantenimiento menor / DIY): 30 € - 80 €: Sustitución de tubos de silicona del sensor diferencial / limpieza de tomas (Limpieza de sensor, cambio de filtro de combustible, revisión de fusibles o conectores.); Nivel 2 (Sustitución de componente): 120 € - 260 €: Cambio de sensor de presión diferencial (DPS) y calibración de punto cero (Sustitución de componente individual (válvula reguladora, unidad dosificadora o inyector reconstruido).); Nivel 3 (Subconjunto mayor): 1.200 € - 2.800 €: Sustitución del filtro DPF OEM en caso de rotura interna de la cerámica (Revisión de bomba de alta presión, juego de inyectores nuevos o sustitución del conjunto DPF.). Tarifas de referencia de talleres. Más del 70% de las incidencias se resuelven en Nivel 1 o 2 sin sustituir subconjuntos completos.
Can I fix code P2002 by doing a forced regeneration or taking the car for an aggressive highway drive?
No, absolutely not. In fact, performing a forced regeneration on a DPF with code P2002 is extremely dangerous. P2002 indicates that the filter substrate is already cracked, damaged, or leaking soot. Forcing an active regeneration pumps extra diesel fuel into the exhaust, creating extreme temperatures (600°C-800°C) that will expand the existing ceramic cracks, melt remaining cells into molten slag, and potentially start an undercarriage fire.
Why is there black soot in my exhaust tailpipe if the car has a Diesel Particulate Filter?
On a healthy diesel vehicle with an intact DPF, there should be zero black soot in the tailpipe-you can wipe it with a white handkerchief and it will come away clean. If there is velvety black soot coating the tailpipe tip, the DPF substrate has cracked internally or melted. The porous ceramic channel walls have broken down, allowing raw exhaust soot to bypass the filter entirely. When this occurs, the DPF must be replaced.
Can a bad differential pressure sensor cause a false P2002 code?
Yes. If the differential pressure sensor has drifted electrically and reports lower pressure than is actually present, or if the rubber hose connecting the front of the DPF to the sensor has split, the sensor will report near-zero delta-P. The ECM interprets this as a hollow or cracked DPF and triggers P2002. Always check the sensor hoses and calibrate Key-ON sensor voltage (must be 0.50V) before replacing the filter.