BOSCH
0261500298
Voir les spéc.
SolenoidBosch HDEV5 / HDEV6 Gasoline Direct Injection (GDI, 200 bar)Euro 56
BOSCH 0261500298 Injecteur Haute Pression Ford Mustang Focus RS Explorer 2.3L EcoBoost
Plateforme moteur:Ford 2.0L & 2.3L EcoBoost (DOHC 16V GTDI Twin-Scroll Turbo) →
RÉFÉRENCE OE
EJ7Z-9F593-A, EJ7G-9F593-AA, 0261500105, FJ1216, CM5238SOUPAPE DE COMMANDE
-NEZ D'INJECTEUR
-PRESSION DE SERVICE
200 barNORME ANTIPOLLUTIONEuro 5 / Euro 6
GARANTIE12 Mois
02
Compatibilité véhicules et motorisations
03
Spécifications techniques
| Spécification | Valeur |
|---|---|
| part_number | 0261500298 |
| oem_reference | EJ7Z-9F593-A |
| manufacturer | BOSCH |
| system_type | Fuel Injector |
| pressure_rating | 200 bar (2900 psi) |
| operating_temperature | -40°C to +135°C |
| flange_mount_torque | 15 N-m (11 lb-ft) |
| high_pressure_line_torque | 28 N-m (21 lb-ft) |
| diagnostic_dtc | P0300, P0301, P0172, P0087 |
| Pression de serviceSpéc. clé |
ENSEMBLE SYSTÈME
Pompe haute pression associée (Ensemble circuit de carburant)
Fonctionne sur le même circuit haute pression Common Rail. En cas de chute de pression (P0087), vérifier le débit de la pompe avant de remplacer les injecteurs.
BOSCHCorrespondance moteur & châssis exacte
0261520134Gasoline Direct Injection (GDI) • 200 bar
🚙 Ford Explorer 2.3 (FORD 2.0L & 2.3L ECOBOOST)
BOSCHCorrespondance moteur & châssis exacte
AG9Z-9350-BGasoline Direct Injection (GDI) • 150 bar
🚙 Ford Explorer 2.3 (FORD 2.0L & 2.3L ECOBOOST)
BOSCHCorrespondance moteur & châssis exacte
BB5Z-9350-AGasoline Direct Injection (GDI) • 200 bar
🚙 Ford Explorer 2.3 (FORD 2.0L & 2.3L ECOBOOST)
BOSCHCorrespondance moteur & châssis exacte
0261520152Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code FORD 2.0L & 2.3L ECOBOOST
BOSCHCorrespondance moteur & châssis exacte
CJ5Z-9350-BGasoline Direct Injection (GDI) • 150 bar
🚙 Engine Code FORD 2.0L & 2.3L ECOBOOST
04
Conseils de montage
- Depressurize the fuel system completely via diagnostic scan tool or by removing the fuel pump fuse prior to line disassembly.
- Clean all surrounding bracket areas thoroughly using residue-free brake cleaner to prevent abrasive particulate ingress.
- Inspect the mechanical camshaft lobe and roller follower or clean injector bore seating surfaces before hardware alignment.
- Install component using fresh factory O-rings or Teflon combustion chamber seals lubricated only with clean motor oil.
- Torque mounting flange fasteners in alternating increments to 15 N-m (11 lb-ft).
- Torque high-pressure hydraulic tube fittings using a calibrated flare nut wrench to 28 N-m (21 lb-ft).
- Prime low-pressure fuel circuit, cycle ignition key 3-4 times, and inspect for high-pressure hydraulic leaks before road test.
Conseils & Avertissements :
- Always replace single-use high-pressure metal fuel lines and micro-filter seals whenever disconnected.
- Verify camshaft driving lobe surfaces for scoring or flat spots before installing any mechanical pump.
- Reset long-term and short-term fuel trim adaptations via OBD-II diagnostic scanner after physical replacement.
05
Codes de Defaut (DTC) & Protocoles de Diagnostic
Codes de defaut diagnostiques (DTC) courants déclenchés lorsque cet injecteur common rail subit une usure, des pannes de circuit ou une dérive d'étalonnage:
P0087Critical
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
P0201 - P0208High
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
P0300 / P0301+High
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
P0088High
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
PROTOCOLES D'ATELIER
Protocoles Techniques de Diagnostic & Réparation
Procédures d'atelier vérifiées, seuils de test et guides d'intervention pour cet ensemble.
DIAGNOSTIC COMMON RAIL D
Lire le protocole techniqueDiagnostic Régulateur Débit IMV SCV & Test P0088 CR
PROTOCOLE DE DIAGNOSTIC OBD-II
Lire le protocole techniqueGuide de diagnostic P0087 : Pression de rampe trop basse
SOP DIAGNOSTIC ATELIER DIESEL
Lire le protocole techniqueDiagnostic Équilibrage Cylindre & Déviation Injecteur
PROTOCOLE D
Lire le protocole technique