12634491
HITACHI 12634491 Pompe Haute Pression Chevy Camaro Regal Cadillac ATS 2.0T
12658339, 12651170, HPP0008, HM10014, GDP104, 12641847--150 barCompatibilité véhicules et motorisations
| Véhicule | Moteur | Années |
|---|---|---|
| Cadillac ATS / ATS-L 2.0T | GM 2.0L Ecotec Turbo SIDI (LTG / LSY Tripower / LHU) | 2013-2019 |
| Buick Regal GS / Regal 2.0T | GM 2.0L Ecotec Turbo SIDI (LTG / LSY Tripower / LHU) | 2014-2020 |
| Buick Envision 28T AWD | GM 2.0L Ecotec Turbo SIDI (LTG / LSY Tripower / LHU) | 2015-2020 |
| Chevrolet Camaro 2.0T | GM 2.0L Ecotec Turbo SIDI (LTG / LSY Tripower / LHU) | 2016-2020 |
Spécifications techniques
| Spécification | Valeur |
|---|---|
| Part Number / SKU | 12634491 |
| Manufacturer Brand | HITACHI |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | GM 2.0L Ecotec Turbo SIDI DOHC (LTG) |
| Pression de serviceSpéc. clé | |
| Mounting Torque (Flange / Bracket) | 13 N-m (115 lb-in) |
| Fuel Line / Rail Torque | 30 N-m (22 lb-ft) |
| Codes défauts fréquents | P0087, P0088, P0089, P0171 |
Pompe haute pression associée (Ensemble circuit de carburant)
Fonctionne sur le même circuit haute pression Common Rail. En cas de chute de pression (P0087), vérifier le débit de la pompe avant de remplacer les injecteurs.
Conseils de montage
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 13 N-m (115 lb-in), and torque fuel line fittings to 30 N-m (22 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
Codes de Defaut (DTC) & Protocoles de Diagnostic
Codes de defaut diagnostiques (DTC) courants déclenchés lorsque cet injecteur common rail subit une usure, des pannes de circuit ou une dérive d'étalonnage:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Protocoles Techniques de Diagnostic & Réparation
Procédures d'atelier vérifiées, seuils de test et guides d'intervention pour cet ensemble.