SIEMENS VDO
13537585261
Ver Especificações
SolenoidGasoline Direct Injection (GDI)Euro 525
SIEMENS VDO 13537585261 Injetor Index 12 BMW 335i 535i 135i 3.0T N54 Piezo
Plataforma do motor:BMW N54B30 / N63B44 / S63 (3.0L I6 & 4.4L V8 Twin-Turbo Piezo) →
REFERÊNCIA OE
13537585261-12, 13537565138, 13537585261-11, FJ1055VÁLVULA DE CONTROLO
-BICO INJETOR
-PRESSÃO DO RAIL
200 barEMISSÕESEuro 5 / Tier 2 Bin 5 / LEV II
GARANTIA12 Meses
03
Especificações Técnicas
| Especificação | Valor |
|---|---|
| Part Number / SKU | 13537585261 |
| Manufacturer Brand | SIEMENS VDO |
| Component Type | Direct Fuel Injector |
| Engine Application | BMW 3.0L Twin-Turbo Inline-6 DOHC 24V (N54B30) |
| Pressão de trabalhoEspec. Principal | |
| Mounting Torque (Flange / Bracket) | 13 N-m (115 lb-in) |
| Fuel Line / Rail Torque | 23 N-m (17 lb-ft) |
| Códigos de falha comuns | P0300, P0301, P0302, P0171, P0172 |
04
Dicas de instalação
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 13 N-m (115 lb-in), and torque fuel line fittings to 23 N-m (17 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
05
Codigos de Falha (DTC) e Protocolos de Diagnostico
Codigos de falha diagnosticos (DTC) comuns acionados quando este injetor common rail apresenta desgaste, falhas de circuito ou desvio:
P0087Critical
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
P0201 - P0208High
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
P0300 / P0301+High
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
P0088High
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
PROTOCOLOS DE OFICINA
Protocolos Técnicos de Diagnóstico & Manutenção
Procedimentos de oficina verificados, valores limite de teste e normas de serviço para este conjunto.
DIAGNÓSTICO DIESEL COMMON RAIL DE OFICINA
Ler protocolo técnicoDiagnóstico da Válvula Dosadora IMV SCV e Teste P0088
PROTOCOLO DE DIAGNÓSTICO OBD-II
Ler protocolo técnicoGuia de Diagnóstico de Baixa Pressão no Rail - DTC P0087
POP DE DIAGNÓSTICO DIESEL COMMON RAIL
Ler protocolo técnicoDiagnóstico de Equilíbrio de Cilindros e Injetores Diesel
PROTOCOLO DE MONTAGEM E INSTALAÇÃO
Ler protocolo técnico