PY8W-13-350
DENSO PY8W-13-350 Högtryckspump Mazda CX-9 CX-5 Mazda 6 2.5T SkyActiv-G
PY8W-13-350A, GDP501--200 barPassande fordon & motorer
| Fordon | Motor | Årsmodell |
|---|---|---|
| Mazda Mazda 3 2.0 / 2.5 | Mazda 2.0L & 2.5L SkyActiv-G / 2.5T Turbo (PE-VPS / PY-VPS / PY-VPTS) | 2014-2023 |
| Mazda CX-5 2.0 / 2.5 | Mazda 2.0L & 2.5L SkyActiv-G / 2.5T Turbo (PE-VPS / PY-VPS / PY-VPTS) | 2013-2023 |
| Mazda Mazda 6 2.5 | Mazda 2.0L & 2.5L SkyActiv-G / 2.5T Turbo (PE-VPS / PY-VPS / PY-VPTS) | 2014-2021 |
Tekniska specifikationer
| Specifikation | Värde |
|---|---|
| Part Number / SKU | PY8W-13-350 |
| Manufacturer Brand | DENSO |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Mazda 2.5L Turbo SkyActiv-G DOHC 16V (PY-VPTS / PY-VPS) |
| ArbetstryckHuvudspec. | |
| Mounting Torque (Flange / Bracket) | 20 N-m (15 lb-ft) |
| Fuel Line / Rail Torque | 30 N-m (22 lb-ft) |
| Vanliga felkoder | P0087, P0088, P0171, P0191 |
Matchande högtryckspump (Bränslekretsmontering)
Fungerar på samma högtrycks-common-railkrets. Vid lågt railtryck (P0087), kontrollera pumpens flöde innan injektorer byts ut.
Monteringsanvisningar
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 20 N-m (15 lb-ft), and torque fuel line fittings to 30 N-m (22 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
Felkoder (DTC) och Diagnosprotokoll
Vanliga diagnosfelkoder (DTC) som aktiveras nar denna common rail-injektor uppvisar slitage, kretsfel eller kalibreringsavvikelse:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Tekniska Diagnos- och Serviceprotokoll
Verifierade verkstadsrutiner, testgränsvärden och serviceinstruktioner för denna komponent.