0261520448
BOSCH 0261520448 Bomba Alta Presión Jeep Wrangler JL Alfa 2.0T Hurricane GME
68249673AA, 68249673AB, 68249673AC, 0261520449, 50051489, 50053438Integrated Pulse-Width Modulated Electric Inlet Metering Valve-200 barAplicaciones de vehículos y motores
| Vehículo | Motor | Años |
|---|---|---|
| Jeep Wrangler JL 2.0T | Stellantis / FCA 2.0L GME T4 Hurricane Turbo (EC1 Jeep / Alfa Romeo) | 2018-2024 |
| Jeep Grand Cherokee 2.0T 4xe | Stellantis / FCA 2.0L GME T4 Hurricane Turbo (EC1 Jeep / Alfa Romeo) | 2021-2024 |
| Alfa Romeo Giulia 2.0T | Stellantis / FCA 2.0L GME T4 Hurricane Turbo (EC1 Jeep / Alfa Romeo) | 2017-2024 |
Especificaciones técnicas
| Especificación | Valor |
|---|---|
| Pump Generation | Bosch HDP-5 Compact Gasoline Direct Injection Pump |
| Max Operating Rail PressureDato clave | |
| Drive Mechanism | Camshaft Driven Roller Tappet Interface |
| Mounting Flange Fastener Torque | 10 N·m + 60°(TTY Bolts) |
| High Pressure Output Line Torque | 30 N·m Flare Nut |
| Control Valve ResistanceDato clave | |
| Typical Diagnostic Trouble Code | P0087 (Fuel Rail Pressure Low - Limp Mode Entry) |
| Wear Item Inspection | Always check roller tappet face for scoring or flat spots during pump replacement |
| Presión de servicioDato clave |
Bomba de alta presión compatible (Ensamblaje del circuito de combustible)
Funciona en el mismo circuito de alta presión Common Rail. Al diagnosticar baja presión (P0087), verifique el caudal de la bomba antes de sustituir los inyectores.
Consejos de instalación
- [
- {
- "step": 1,
- "title": "Depressurize Fuel System Safely",
- "instruction": "Disconnect low pressure tank pump power connector. Crank engine 10 seconds. Check live scan data confirming low pressure fuel drops below 5 bar."
- },
- {
- "step": 2,
- "title": "Inspect & Replace Roller Tappet",
- "instruction": "Extract roller lifter from cylinder head bore. Inspect roller surface and internal bearing for scoring. Replace if surface DLC coating shows signs of wear."
- },
- {
- "step": 3,
- "title": "Set Camshaft to Lowest Base Circle",
- "instruction": "Rotate crankshaft until driving cam lobe is at lowest lift. This minimizes spring resistance when seating new pump onto mounting flange."
- },
- {
- "step": 4,
- "title": "Torque Mounting Bolts with Angle",
- "instruction": "Fit new O-ring lubricated with clean engine oil. Snug bolts down evenly, then torque to 10 N\u00b7m plus an additional 60-degree rotation."
- },
- {
- "step": 5,
- "title": "Secure High Pressure Hard Line",
- "instruction": "Line up high pressure steel line. Hand thread fitting to prevent cross-threading, then torque to 30 N\u00b7m with flare wrench."
- }
- ]
Codigos de Falla (DTC) y Protocolos de Diagnostico
Codigos de falla de diagnostico (DTC) comunes que se activan cuando este inyector common rail experimenta desgaste, fallas de circuito o desbalance:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Protocolos Técnicos de Diagnóstico y Servicio
Procedimientos de taller verificados, umbrales de prueba y pautas de servicio para este conjunto.