31303495
DENSO 31303495 Injecteur Haute Pression Volvo XC90 XC60 S90 2.0T Drive-E T5 T6
31465786, 31336691, 31336692, 0261500366High-Speed Electromagnetic Multi-Hole Micro Solenoid-200 barCompatibilité véhicules et motorisations
Spécifications techniques
| Spécification | Valeur |
|---|---|
| Type de système | Denso Multi-Hole Laser Direct Gasoline Fuel Injector |
| Pression de serviceSpéc. clé | |
| Spray Geometry | Precision laser-drilled asymmetric spray cone targeting intake swirl |
| Fuel Rail Bolt Torque | 11 N·m (flanged rail bracket fasteners) |
| High Pressure Pipe Torque | 25 N·m (fuel delivery rail pipe union) |
| Solenoid Coil Resistance | 1.7 - 2.1 Ω at 20°C (rapid actuation pulse circuit) |
| Codes défauts fréquents | P0300 (Random Misfire), P0301-P0304 (Cylinder Misfire), P0171 (System Lean Bank 1) |
| Workshop Precaution | Always fit new Teflon combustion chamber seal rings using expansion mandrel and calibration collet |
Pompe haute pression associée (Ensemble circuit de carburant)
Fonctionne sur le même circuit haute pression Common Rail. En cas de chute de pression (P0087), vérifier le débit de la pompe avant de remplacer les injecteurs.
Conseils de montage
- [
- {
- "step": 1,
- "title": "Depressurize Fuel System & Remove Air Filter Housing",
- "instruction": "Depressurize fuel rail via diagnostic scan tool command. Remove intake air filter ducting and upper acoustic shield."
- },
- {
- "step": 2,
- "title": "Disconnect Injector Harness & High Pressure Delivery Rail",
- "instruction": "Unclip wiring harness from all four injectors. Loosen high-pressure delivery pipe (25 N·m) and unbolt fuel rail retaining screws (11 N·m)."
- },
- {
- "step": 3,
- "title": "Extract Injectors & Install Replacement Teflon Radial Seals",
- "instruction": "Withdraw direct injectors using slide puller. Clean carbon deposits from cylinder head bores. Install new Teflon seals and resize with calibration sleeve."
- },
- {
- "step": 4,
- "title": "Reinstall Fuel Rail Assembly & Torque Connections",
- "instruction": "Press injectors firmly into ports. Torque rail bolts evenly to 11 N·m. Tighten high pressure line union to 25 N·m. Start engine and verify zero fuel weepage."
- }
- ]
Codes de Defaut (DTC) & Protocoles de Diagnostic
Codes de defaut diagnostiques (DTC) courants déclenchés lorsque cet injecteur common rail subit une usure, des pannes de circuit ou une dérive d'étalonnage:
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Protocoles Techniques de Diagnostic & Réparation
Procédures d'atelier vérifiées, seuils de test et guides d'intervention pour cet ensemble.