31303495
DENSO 31303495 Yüksek Basınç Enjektörü Volvo XC90 XC60 S90 2.0T Drive-E T5 T6
31465786, 31336691, 31336692, 0261500366High-Speed Electromagnetic Multi-Hole Micro Solenoid-200 barUyumlu Araçlar ve Motorlar
Teknik Özellikler
| Özellik | Değer |
|---|---|
| Sistem Tipi | Denso Multi-Hole Laser Direct Gasoline Fuel Injector |
| Çalışma BasıncıTemel Değer | |
| Spray Geometry | Precision laser-drilled asymmetric spray cone targeting intake swirl |
| Fuel Rail Bolt Torque | 11 N·m (flanged rail bracket fasteners) |
| High Pressure Pipe Torque | 25 N·m (fuel delivery rail pipe union) |
| Solenoid Coil Resistance | 1.7 - 2.1 Ω at 20°C (rapid actuation pulse circuit) |
| Tipik Arıza Kodları | P0300 (Random Misfire), P0301-P0304 (Cylinder Misfire), P0171 (System Lean Bank 1) |
| Workshop Precaution | Always fit new Teflon combustion chamber seal rings using expansion mandrel and calibration collet |
Uyumlu Yüksek Basınç Pompası (Yakıt Devresi Grubu)
Aynı yüksek basınçlı Common Rail devresinde çalışır. Düşük basınç (P0087) teşhisinde enjektörleri değiştirmeden önce pompa debisini kontrol edin.
Montaj İpuçları
- [
- {
- "step": 1,
- "title": "Depressurize Fuel System & Remove Air Filter Housing",
- "instruction": "Depressurize fuel rail via diagnostic scan tool command. Remove intake air filter ducting and upper acoustic shield."
- },
- {
- "step": 2,
- "title": "Disconnect Injector Harness & High Pressure Delivery Rail",
- "instruction": "Unclip wiring harness from all four injectors. Loosen high-pressure delivery pipe (25 N·m) and unbolt fuel rail retaining screws (11 N·m)."
- },
- {
- "step": 3,
- "title": "Extract Injectors & Install Replacement Teflon Radial Seals",
- "instruction": "Withdraw direct injectors using slide puller. Clean carbon deposits from cylinder head bores. Install new Teflon seals and resize with calibration sleeve."
- },
- {
- "step": 4,
- "title": "Reinstall Fuel Rail Assembly & Torque Connections",
- "instruction": "Press injectors firmly into ports. Torque rail bolts evenly to 11 N·m. Tighten high pressure line union to 25 N·m. Start engine and verify zero fuel weepage."
- }
- ]
Ariza Kodlari (DTC) ve Teshis Protokolleri
Bu common rail enjektorunde asinma, devre arizasi veya kalibrasyon kaymasi olustugunda tetiklenen yaygin ariza kodlari (DTC):
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Teknik Arıza Teşhis ve Servis Protokolleri
Bu parça grubu için doğrulanmış atölye prosedürleri, test eşik değerleri ve servis talimatları.