P0002: Stuurstroomkring Brandstofvolumedoseerklep (VCV / IMV) - Bereik / Prestatie
Foutcode (DTC) P0002 geeft aan dat het motorregelapparaat (ECM/PCM) een afwijking in prestatie, correlatie of plausibiliteit heeft vastgesteld in het elektrische aanstuurcircuit van de brandstofvolumedoseerklep (VCV), in de werkplaatspraktijk ook wel aangeduid als inlaatdoseerklep (IMV), MPROP of zuigdrukregelklep (SCV). In moderne common-rail dieselinspuitsystemen (zoals Bosch CP1H, CP3, CP4, Delphi DFP3 en Denso HP3/HP4) is de doseerklep rechtstreeks op het hogedrukpomphuis gemonteerd om de toevoer van lagedrukbrandstof naar de hogedrukplunjers te doseren. DTC P0002 wordt gegenereerd wanneer de interne stroommeetweerstand (shunt) van de ECM detecteert dat de werkelijke stuurstroom buiten de fabriekstoleranties afwijkt van de gewenste stuurwaarde, of wanneer de resulterende drukrespons in de brandstofrail afwijkt van de verwachte volumetrische regelcurves binnen de gesloten regelkring.
🚗 Rijveiligheid, geschatte reparatiekosten & verificatie
- 01
🚦 Rijveiligheid en mechanisch risico
Directe inspectie en noodzaak voor een takelwagenRegelcircuit brandstofvolume-regelklep bereik/werking (VCV / IMV-storing)
De brandstofdoseerklep (VCV / IMV) op de hogedrukpomp kan de inlaatbrandstofstroom niet moduleren. De ECU kan de common-raildruk niet regelen, wat leidt tot een risico op ernstige overdruk of plotselinge motoruitval.
MECHANISCHE RISICO'S BIJ DOORRIJDEN:Ongereguleerde brandstofdrukpieken kunnen de stalen hogedrukleidingen doen barsten, de overdrukventielen openblazen of de interne kleppen van de verstuivers beschadigen. - 02
💰 Typisch werkplaatsbudget
Verwachte kostenstaffels voor onderdelen en arbeidKlein onderhoud / Filter€ 35 - € 85: Reiniging van kabelboom en stekker, controle op doorschuren van de kabelboom naar de doseerklepSensorreiniging, brandstoffilter vervangen, zekering controleren of contacten reinigen.
Klep / Sensor vervangen€ 120 - € 350: Vervanging van originele Bosch/Delphi brandstofdoseerklep IMV/VCVVervanging enkel onderdeel (drukregelventiel, doseereenheid of gereviseerde verstuiver).
Grote revisie / Pomp en injectoren€ 850 - € 2.200: Complete vervanging van de hogedrukpomp CP4/CP3Revisie hogedrukpomp, nieuwe OEM-verstuivers of vervanging DPF-roetfilter.
- 03
🧰 Snelle visuele controle zonder gereedschap
5-minuten garagecheck voordat u de werkplaats belt11. Inspecteer de 2-polige VCV/IMV-stekker op de hogedrukpomp op corrosie, afgebroken vergrendellipjes en brandstoflekkage.22. Meet de interne spoelweerstand van de doseerklep met een multimeter (doorgaans 2,0 tot 4,5 Ohm bij 20 °C).33. Snijd het brandstoffilter open of inspecteer het zeefje van de doseerklep op fijne metaalsplinters (indicator voor CP4-pompschade). - 04
🛡️ Bescherming tegen verkeerde diagnoses
Gerichte vragen aan de monteur om onnodige vervanging te voorkomen""Controleer het gaasfilter van de doseerklep op messing- of staalsplinters voordat u de klep vervangt; als er metaaldeeltjes worden aangetroffen, moet het complete brandstofsysteem worden gespoeld.""
""Controleer met een oscilloscoop of het PWM-aanstuursignaal van de ECU overeenkomt met de duty cycle voordat u aanneemt dat de pomp mechanisch defect is.""
""Zorg dat het brandstofsysteem correct wordt ontlucht met de elektrische lagedruk-opvoerpomp voordat u start, om drooglopen van de nieuwe klep te voorkomen.""
Technische opmerking: Stel deze gerichte vragen aan uw monteur voordat u akkoord gaat met dure reparaties:
30-seconden werkplaatstriage
- Check Engine Light (MIL) illuminated continuously on the dashboard
- Engine hard starting, extended cranking times, or intermittent no-start conditions
- Engine surging, hunting, or unstable rpm fluctuations at idle and during light throttle cruise
- Mechanical sticking, varnish buildup, or metal debris jamming the precision spool inside the Fuel Volume Control Valve (VCV/IMV)
- Internal electrical coil breakdown, thermal resistance drift, or intermittent open winding inside the VCV solenoid
- High electrical contact resistance, terminal pin fretting corrosion, or loose female pins in the VCV two-pin connector
Connect scan tool live telemetry: compare Target Fuel Rail Pressure vs Actual Rail Pressure and log metering valve command PWM duty cycle during idle and road load.
Expensive Diagnostic Pitfall & Technical Reality
P0002 indicates that the high-pressure fuel pump has failed internally and must be replaced as an entire assembly ($1,400 - $2,200).
P0002 is a performance rationality code on the Fuel Volume Control Valve (VCV) or Inlet Metering Valve (IMV) circuit. The electrical circuit is intact (not open or shorted), but the commanded PWM duty cycle does not produce the expected rail pressure response. In over 80% of verified cases, the high-pressure pump is mechanically sound. The failure is driven by micro-varnish gumming on the metering valve plunger, fuel filter restriction causing cavitation, or fuel aeration from damaged low-pressure O-rings.
Unnecessary complete CP3/CP4 pump replacement ($1,650-$2,400 incl. labor) vs replacing the sub-component Bosch MPROP/IMV metering valve ($95-$145, 30-minute repair), saving over $1,500.
Meest getroffen motoren en injectieplatformen
Deze foutcode treedt hoofdzakelijk op bij de volgende common-rail dieselplatforms. Raadpleeg hieronder uw motorfamilie voor fabrieksspecificaties en onderdeelnummers:
Ford 6.7L Powerstroke V8 Diesel
Bosch CP4.2 High-Pressure Common Rail SystemBekende fabriekszwakte: EGR cooler carbon clogging, DEF injector white crust crystallization, fuel volume control valve harness chafing.
BC3Z-9A543-A, FC3Z-9F593-B, BC3Z-5J281-ARenault / Opel 1.9 dCi (F9Q)
Bosch EDC15 / EDC16 Common Rail SystemBekende fabriekszwakte: Injector harness connector diesel seepage, glow plug tip carbon seizure, EGR valve soot accumulation.
7700107165, 0445110021, 8200542997Volkswagen / Audi 2.0 TDI (EA189 / CFFB / CFGB)
Bosch EDC17 Common Rail SystemBekende fabriekszwakte: Piezo stack degradation, injector harness terminal fretting, DPF differential pressure sensor silicone tube split.
03L130277, 0445110369, 076906051AToyota 3.0 D-4D (1KD-FTV / Hilux / Prado)
Denso Common Rail SystemBekende fabriekszwakte: Suction control valve (SCV) stickiness, injector seat washer blow-by, fuel delivery balance deviation.
23670-30050, 095000-5471, 04226-0L010Fuel Metering Valve (IMV/SCV) Diagnostics Guide
Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.
Stuurstroomcircuit & Actuatorlogica
1. Dynamic In-Demand Fuel Metering
The Fuel Volume Control Valve (VCV/IMV) meters fuel on the suction side of the high-pressure pump. By only compressing the exact amount of fuel required by the engine, the system minimizes pump mechanical drive losses and prevents excessive fuel heating in the return circuit. The VCV is actuated via a Pulse-Width Modulated (PWM) current-controlled solenoid operated at frequencies between 100 Hz and 1,000 Hz. Depending on pump design, valves are either Normally Open (NO, e.g., Bosch CP3/CP4, where 0% duty cycle delivers maximum fuel) or Normally Closed (NC, e.g., some Denso and Delphi systems, where 0% duty cycle delivers zero fuel).
2. Closed-Loop PID Deviation Monitoring
The ECM's internal micro-controller commands target current (typically 0.0 A to 1.8 A) rather than simple voltage duty cycle. A high-speed current sensing amplifier measures actual current flowing through the coil on every PWM pulse. If the ECM commands 1.20 A but measures < 0.70 A or > 1.60 A, or if the drive current oscillates erratically due to internal plunger mechanical stick-slip friction, the ECM detects that the volume regulator cannot maintain rail stability, flagging DTC P0002 and triggering Limp-Home mode.
3. Diagnostic Trap: Normally Open (NO) vs Normally Closed (NC) Valves
Normally Open (NO) vs Normally Closed (NC) Emergency Behavior: On Bosch CP3 and CP4 systems, the VCV is Normally Open. If electrical power is lost, the internal spring forces the valve wide open, allowing the pump to build maximum rail pressure (relieved by the rail pressure control valve or mechanical pressure limiter). On Normally Closed systems, losing electrical control starves the pump of fuel, causing immediate engine stalling. Confirming valve architecture is vital for workshop diagnosis.
Elektrische & Hydraulische referentiewaarden
Stap-voor-stap Werkplaatsprotocol
Remove VCV / IMV and Inspect for Metal Shavings (Glitter Test)
Before performing electrical tests, disconnect the VCV connector and remove the two Torx hold-down bolts securing the valve to the high-pressure pump body. Carefully extract the valve and inspect the micro-mesh inlet screen and O-rings using a bright inspection light and a strong neodymium magnet. If metallic flakes, bronze dust, or silvery particles are found, the high-pressure pump has suffered internal mechanical failure; the entire fuel system (pump, rail, injectors, tank, lines) must be replaced.
Measure VCV Solenoid Coil Resistance at 20°C & Thermal Soak
Using a precision digital multimeter on the 200 Ω scale with zeroed test leads, measure resistance across the two VCV terminal pins at 20°C. Bosch CP3/CP4: 2.5-3.8 Ω; Delphi IMV: 5.0-5.8 Ω; Denso SCV: 1.5-2.5 Ω. Heat the valve with an industrial heat gun to 80°C and re-measure. Resistance must rise smoothly without open-circuit spikes (infinite resistance), which indicate broken internal copper wire bonds.
High-Voltage Insulation Resistance Test
Using a Megohmmeter set to 250V or 500V DC, test insulation resistance between each VCV terminal pin and the metal valve body. The resistance must exceed 10 MΩ. Any reading below 10 MΩ indicates internal insulation breakdown where drive current arcs to the engine block, tripping driver protection in the ECM.
Oscilloscope Current Clamp Waveform Analysis
Reinstall the VCV (with new oiled O-rings). Connect an oscilloscope current clamp (20A or 60A range) around one of the two harness wires. Start the engine and observe the current waveform at idle. You should see a clean sawtooth current waveform averaging 1.0A-1.4A. Look for jagged current dips or erratic current spikes that indicate the mechanical valve spool is sticking inside its sleeve.
Wiring Harness Continuity & Dynamic Load Test
Disconnect the ECM main harness connector. Measure continuity on both wires between the ECM and VCV plug (must read < 0.4 Ω). Perform a circuit load test using a 12V 21W automotive bulb connected across the power and ground lines to verify that the harness can support 2.0 Amperes of operating current without high-resistance voltage drops.
Low-Pressure Fuel Delivery Pressure & Vacuum Test
Connect a fuel pressure gauge to the inlet of the high-pressure fuel pump. Measure feed pressure during idle and full throttle. Electric lift pump systems must deliver 4.5-6.5 bar stable pressure. Internal mechanical suction gear pumps must pull between -0.3 and -0.45 bar vacuum. A restricted fuel filter will starve the VCV of fuel, creating erratic pressure response that mimics a metering valve failure.
Reparatie op hardwareniveau & Onderdelenlijst
High-Pressure Pump Fuel Quantity Control (Inlet Metering Valve / MPROP)
0 928 400 660 / 0 928 400 706
Regulates low-pressure fuel flow into high-pressure pumping chambers via PWM signal
F 00R 000 756 / 1 110 010 015
Mechanical safety pressure dump valve preventing overpressure rail rupture
F 00N 200 098
Prevents air ingress and internal bypass leakage at the metering unit flange
Interactieve Common Rail Tolerantiecalculator
Bijbehorende brandstofinjectieonderdelen
The following genuine OEM fuel pumps and common rail injectors are verified factory equipment for engines reporting fault protocol P0002. Cross-reference operating pressures and tightening torques before sub-assembly replacement:
0445110021BOSCH
BOSCH 0445110021 - F9Q 1.9 dCi Common Rail Injector
View Technical Specs & Fitment →0445110369BOSCH
0445110369 Injector: VW 2.0 TDI EA189 CFFB CFHC Specs
View Technical Specs & Fitment →095000-5471DENSO
095000-5471 Denso Isuzu 4HK1 Injector: 8-97329703-4 Specs
View Technical Specs & Fitment →06H127025NBOSCH
BOSCH 06H127025N High Pressure Fuel Pump Audi A4 A5 Q5 VW Tiguan 2.0 TFSI EA888 Gen2 0261520141
AG9Z-9350-BBOSCH
BOSCH AG9Z-9350-B High Pressure Fuel Pump Ford Edge Fusion Focus ST Taurus 2.0L EcoBoost 0261520152
04E127025BBOSCH
BOSCH 04E127025B High Pressure Fuel Pump VW Golf Tiguan Jetta Audi A3 1.4 TSI EA211 0261520216
View Technical Specs & Fitment →Pomp-adaptatiereset & Inleer-proefrit
Following the replacement, cleaning, or overhaul of the Fuel Volume Control Valve (VCV/IMV) for DTC P0002:
1. Clear all stored trouble codes from the Engine Control Module using a diagnostic scan tool.
2. Access ECM Special Functions -> 'Reset High-Pressure Fuel Pump / Volume Control Valve Adaptation Values'.
3. Switch ignition OFF and wait 60 seconds to allow the ECM main relay to power down and save non-volatile memory.
4. Perform a low-pressure fuel system bleed: cycle the electric lift pump 3 times for 30 seconds each (via scan tool active test) to purge air.
5. Start the engine and idle for 10 minutes without touching the accelerator pedal to allow the ECM to calibrate minimum drive current and rail stability offsets.
6. Conduct a road test including deceleration fuel cutoff sequences to calibrate overrun rail pressure decay rates.
Differentiaaldiagnose & Gerelateerde fouten
Praktijkgevallen uit de werkplaats
2016 Ford Transit 2.2 TDCi (Puma ZSD-422)(175,000 km)
Veelgestelde technische vragen
Wat betekent motorfoutcode P0002?
Foutcode (DTC) P0002 geeft aan dat het motorregelapparaat (ECM/PCM) een afwijking in prestatie, correlatie of plausibiliteit heeft vastgesteld in het elektrische aanstuurcircuit van de brandstofvolumedoseerklep (VCV), in de werkplaatspraktijk ook wel aangeduid als inlaatdoseerklep (IMV), MPROP of zuigdrukregelklep (SCV). In moderne common-rail dieselinspuitsystemen (zoals Bosch CP1H, CP3, CP4, Delphi DFP3 en Denso HP3/HP4) is de doseerklep rechtstreeks op het hogedrukpomphuis gemonteerd om de toevoer van lagedrukbrandstof naar de hogedrukplunjers te doseren. DTC P0002 wordt gegenereerd wanneer de interne stroommeetweerstand (shunt) van de ECM detecteert dat de werkelijke stuurstroom buiten de fabriekstoleranties afwijkt van de gewenste stuurwaarde, of wanneer de resulterende drukrespons in de brandstofrail afwijkt van de verwachte volumetrische regelcurves binnen de gesloten regelkring.
Wat zijn de meest voorkomende symptomen van P0002?
Check Engine Light (MIL) illuminated continuously on the dashboard, Engine hard starting, extended cranking times, or intermittent no-start conditions, Engine surging, hunting, or unstable rpm fluctuations at idle and during light throttle cruise, Sudden engine stalling during deceleration or when coming to a complete stop at intersections, Severe loss of vehicle power with ECM locking into Limp-Home mode, Audible intermittent diesel combustion rattle or sharp knocking caused by rail pressure spikes.
Wat veroorzaakt P0002 bij een dieselmotor?
Mechanical sticking, varnish buildup, or metal debris jamming the precision spool inside the Fuel Volume Control Valve (VCV/IMV); Internal electrical coil breakdown, thermal resistance drift, or intermittent open winding inside the VCV solenoid; High electrical contact resistance, terminal pin fretting corrosion, or loose female pins in the VCV two-pin connector; Chafed, pinched, or partially broken wiring harness wires between the ECM and the high-pressure pump metering valve; Severe fuel contamination (water, gasoline, particulate debris) causing loss of diesel lubricity and valve plunger scoring; Failing ECM internal current-sensing shunt resistor or damaged low-side MOSFET driver transistor.
Is het veilig om te rijden met actieve code P0002?
🟡 Pas op: Noodloop actief / Bezoek werkplaats
Wat kost het repareren van foutcode P0002?
De gemiddelde reparatiekosten voor storingscode P0002 hangen af van de exacte oorzaak en het diagnoseniveau: Niveau 1 (Klein onderhoud / Doe-het-zelf): € 35 - € 85: Reiniging van kabelboom en stekker, controle op doorschuren van de kabelboom naar de doseerklep (Sensorreiniging, brandstoffilter vervangen, zekering controleren of contacten reinigen.); Niveau 2 (Vervanging onderdeel): € 120 - € 350: Vervanging van originele Bosch/Delphi brandstofdoseerklep IMV/VCV (Vervanging enkel onderdeel (drukregelventiel, doseereenheid of gereviseerde verstuiver).); Niveau 3 (Revisie hoofdsysteem): € 850 - € 2.200: Complete vervanging van de hogedrukpomp CP4/CP3 (Revisie hogedrukpomp, nieuwe OEM-verstuivers of vervanging DPF-roetfilter.). Werkplaatsreferentietarieven. Meer dan 70% van de gevallen wordt opgelost binnen niveau 1 of 2 zonder vervanging van complete subeenheden.
Can I replace just the VCV without replacing the high-pressure pump?
Yes, provided there are no metal shavings or debris inside the pump! If the valve has simply failed electrically (open coil) or suffered varnish stick-slip from low-quality fuel, installing a new VCV with fresh O-rings will completely solve DTC P0002.
Why does a faulty VCV cause engine surging at idle?
The ECM continuously adjusts the VCV PWM current in microsecond increments to maintain rock-steady rail pressure. If the valve plunger is sticky, it resists movement until current builds up, then jumps too far. This causes rail pressure to oscillate wildly by 50-150 bar, making engine idle hunt and surge.
What is the difference between a VCV (Inlet Metering) and a PCV (Rail Regulator)?
The VCV (Volume Control Valve / IMV) meters low-pressure fuel entering the high-pressure pump. The PCV (Pressure Control Valve / DRV) is mounted on the common rail and dumps excess high-pressure fuel back to the tank. Modern common rail systems use both valves to manage rail pressure efficiently.