13518641789
BOSCH 13518641789 Yüksek Basınç Pompası BMW M340i 540i X3 Supra B58 TU 3.0T
8641789, 13518631642, 8631642, 0261520521Integrated Electronic Quantity Control Solenoid Valve-350 barUyumlu Araçlar ve Motorlar
Teknik Özellikler
| Özellik | Değer |
|---|---|
| Sistem Tipi | Bosch HDP6 350-bar Mechanical Plunger High-Pressure Fuel Pump |
| Çalışma BasıncıTemel Değer | |
| Drive Actuation | Triple-lobe exhaust camshaft actuation via roller tappet bucket |
| Mounting Flange Bolt Torque | 13 N·m (alternately tightened in half-turn increments) |
| High Pressure Line Torque | 28 N·m (rigid high-pressure delivery pipe union) |
| Quantity Control Valve ResistanceTemel Değer | |
| Tipik Arıza Kodları | P0087 (Fuel Rail Pressure Low), P102A (Fuel Rail Volume Mismatch), P0171 (Lean Fuel Trim) |
| Workshop Precaution | Inspect roller tappet for surface galling; replace high-pressure fuel supply pipe if flare fitting shows deformation |
Uyumlu Yüksek Basınç Pompası (Yakıt Devresi Grubu)
Aynı yüksek basınçlı Common Rail devresinde çalışır. Düşük basınç (P0087) teşhisinde enjektörleri değiştirmeden önce pompa debisini kontrol edin.
Montaj İpuçları
- [
- {
- "step": 1,
- "title": "Depressurize Fuel Rail & Disconnect 12V Battery",
- "instruction": "Disable electric low-pressure in-tank pump fuse and crank until rail pressure falls below 5 bar. Disconnect battery negative terminal."
- },
- {
- "step": 2,
- "title": "Remove Engine Strut Braces & Acoustic Engine Cover",
- "instruction": "Remove upper strut braces over valve cover. Unclip acoustic sound suppression shield around high-pressure pump chamber."
- },
- {
- "step": 3,
- "title": "Unbolt High Pressure Unions & Flange Bolts Evenly",
- "instruction": "Disconnect flow metering solenoid harness. Unthread high-pressure pipe flare nut (28 N·m). Back out two flange mounting bolts evenly half-turn at a time."
- },
- {
- "step": 4,
- "title": "Install HPFP, Torque Mounting Bolts & Check for Leaks",
- "instruction": "Lubricate roller tappet bucket with clean engine oil. Seat pump and torque flange bolts to 13 N·m. Tighten high pressure line to 28 N·m. Verify zero leaks."
- }
- ]
Ariza Kodlari (DTC) ve Teshis Protokolleri
Bu common rail enjektorunde asinma, devre arizasi veya kalibrasyon kaymasi olustugunda tetiklenen yaygin ariza kodlari (DTC):
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
Teknik Arıza Teşhis ve Servis Protokolleri
Bu parça grubu için doğrulanmış atölye prosedürleri, test eşik değerleri ve servis talimatları.