Ford 2.0L Duratec 20 GDI Ti-VCT DOHC 16-Valve Inline-4 Naturally Aspirated Diesel Injector
Cross-Reference & Technical Specs
Authoritative technical specifications, verified Bosch part numbers, control valve stamping codes, nozzle spray orifices, and hold-down tightening torque for the Ford 2.0L Duratec 20 GDI Ti-VC diesel engine family.
All Verified Part Numbers for Ford 2.0L Duratec 20 GDI Ti-VCT DOHC 16-Valve Inline-4 Naturally Aspirated
The following 1 common-rail injector assembly is calibrated for this engine family. Click the SKU to view individual test bench flow curves, sister cross-references, and vehicle applications.
High-Response Multi-Hole Electromagnetic Direct Injection NozzleNozzle Code: See Product Detail| Part Number (SKU) | Primary OE Reference | Control Valve | Nozzle Code |
|---|---|---|---|
| CM5Z-9F593-B, 0261500073, 0261500074 | High-Response Multi-Hole Electromagnetic Direct Injection Nozzle | See Product Detail |
Verified Vehicle Compatibility
Installation, Tightening Torque & Re-torque Protocol
Strict torque compliance is mandatory on Ford 2.0L Duratec 20 GDI Ti-VCT DOHC 16-Valve Inline-4 Naturally Aspirated common-rail cylinder heads. Over-torquing stretches the injector body or strips the head clamping threads, while under-torquing allows combustion blow-by past the copper sealing washer:
- Hold-down clamp bolt: 10 N·m (cold state). Always clean the cylinder head recess with an injector seat reamer.
- High-pressure rail flare nut: 25-30 N·m using a dedicated 17 mm line wrench.
- Return leak-off banjo bolt: 9-12 N·m with fresh copper washers on both sides of the banjo union.
After fitting replacement injectors on Ford 2.0L Duratec 20 GDI Ti-VCT DOHC 16-Valve Inline-4 Naturally Aspirated, generate or program the cylinder-specific IMA calibration code into the engine ECU using an OEM-level scan tool (Bosch KTS, Renault CLIP, or VAG-COM) to prevent cylinder power imbalance and rough idle.
Technical Diagnostics FAQ for Ford 2.0L Duratec 20 GDI Ti-VCT DOHC 16-Valve Inline-4 Naturally Aspirated
What DTC fault codes indicate a failing injector on Ford 2.0L Duratec 20 GDI Ti-VCT DOHC 16-Valve Inline-4 Naturally Aspirated?
The most frequent fault codes are P0201 through P0204 (Injector Circuit Malfunction on Cylinders 1-4), P2146/P2149 (Injector Group Supply Voltage Error), and P0087 (Fuel Rail Pressure Low due to excessive internal leak-off). Measure solenoid coil resistance across the pins (0.5-1.5 Ω) and perform a graduated-bottle dynamic leak-back test to pinpoint the leaking cylinder.
Can sister SKUs within the Ford 2.0L Duratec 20 GDI Ti-VCT DOHC 16-Valve Inline-4 Naturally Aspirated family be interchanged?
Not unless explicitly confirmed on the vehicle build plate. While sister SKUs share the same physical outer envelope and High-Response Multi-Hole Electromagnetic Direct Injection Nozzle control valve, they differ in nozzle spray orifice angle and factory IMA flow calibration. Mixing sister SKUs on the same engine block can trigger rough idle, elevated exhaust gas temperatures (EGT), and MOT emissions failure.
Which specific Bosch injectors fit the Ford 2.0L Duratec 20 GDI Ti-VCT DOHC 16-Valve Inline-4 Naturally Aspirated engine?
The verified genuine Bosch common-rail injectors engineered for the Ford 2.0L Duratec 20 GDI Ti-VCT DOHC 16-Valve Inline-4 Naturally Aspirated engine family are:
- Bosch CM5E-9F593-BB Common Rail Injector → (OE: CM5Z-9F593-B, 0261500073, 0261500074, FJ1151) — Control Valve: High-Response Multi-Hole Electromagnetic Direct Injection Nozzle,