HITACHI
12692510
Voir les spéc.
SolenoidHitachi / GM 200-bar Direct Injection Fuel Delivery SystemEuro 6330
HITACHI 12692510 Pompe Haute Pression Cadillac XT5 Camaro 3.6L LGX
Plateforme moteur:GM 3.6L High Feature V6 SIDI (LFX / LLT / LGX / LFY) →
RÉFÉRENCE OE
12661029, 12677329, 12683984, HM10041, HPP0026, GDP108SOUPAPE DE COMMANDE
Integrated Pulse-Width Modulated Fuel Pressure ActuatorNEZ D'INJECTEUR
-PRESSION DE SERVICE
200 barNORME ANTIPOLLUTIONEuro 6 / Tier 3 Bin 30 / ULEV
GARANTIE12 Mois
03
Spécifications techniques
| Spécification | Valeur |
|---|---|
| Pression de serviceSpéc. clé | |
| Pump Technology | Single Plunger Mechanical Camshaft-Driven HPFP |
| Flow Control | Pulse-Width Modulated Fuel Pressure Regulator Solenoid |
| Mounting Flange Torque | 10 N·m |
| High Pressure Line Torque | 30 N·m |
| Drive Type | Camshaft Multi-Lobe Drive via Hydraulic Roller Lifter |
| Fuel Type | Gasoline Direct Injection (SIDI / Spark Ignition Direct Injection) |
| OE Cross References | 12692510, 12661029, 12677329, 12683984, HM10041, HPP0026 |
| Failure Symptoms | Extended crank, fuel smell in crankcase, P0087 low rail pressure, power reduction mode |
| Diagnostic Test | GDS2 scan tool: Command rail pressure sweeps (40 to 200 bar) at idle and fast idle |
04
Conseils de montage
- [
- "De-energize in-tank fuel pump fuse and crank engine until fuel pressure drops to zero.",
- "Remove sound insulator shroud over cylinder head rear; disconnect pressure regulator harness plug.",
- "Carefully loosen high-pressure steel delivery tube flare nuts while backing up the pump fitting.",
- "Evenly unbolt the two M6 mounting bolts half a turn each to release spring preload without tilting.",
- "Inspect roller lifter and camshaft driving lobe for surface scoring, flaking, or rotational drag.",
- "Lubricate new viton O-ring with fresh synthetic engine oil and insert pump squarely into bore.",
- "Torque mounting bolts in small incremental passes to a final 10 N·m.",
- "Torque high-pressure line flare nut to 30 N·m; reconnect electrical harness and verify zero fuel weeping."
- ]
05
Codes de Defaut (DTC) & Protocoles de Diagnostic
Codes de defaut diagnostiques (DTC) courants déclenchés lorsque cet injecteur common rail subit une usure, des pannes de circuit ou une dérive d'étalonnage:
P0087Critical
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
P0201 - P0208High
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
P0300 / P0301+High
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
P0088High
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
PROTOCOLES D'ATELIER
Protocoles Techniques de Diagnostic & Réparation
Procédures d'atelier vérifiées, seuils de test et guides d'intervention pour cet ensemble.
DIAGNOSTIC COMMON RAIL D
Lire le protocole techniqueDiagnostic Pompe Haute Pression: Code P0087 & Bosch CP4
DIAGNOSTIC COMMON RAIL D
Lire le protocole techniqueDiagnostic Régulateur Débit IMV SCV & Test P0088 CR
PROTOCOLE DE DIAGNOSTIC OBD-II
Lire le protocole techniqueGuide de diagnostic P0087 : Pression de rampe trop basse
DIAGNOSTIC TECHNIQUE COMMON RAIL
Lire le protocole technique