Catálogo / BOSCH / JL3Z-9F593-A
BOSCH

JL3Z-9F593-A

Ver Especificações
SolenoidFord Dual-Fuel PFDI (Port Fuel Injection + 250-bar Direct Injection)Euro 3706

BOSCH JL3Z-9F593-A Injetor Direto Ford F-150 Mustang 5.0L Coyote Gen 3

Dados de referência para injetor Common Rail Bosch JL3Z-9F593-A · OEM 0261500360, 0261500361, FJ1431, JL3E-9F593-AB · Aplicação Ford 5.0L Coyote V8 (Gen 3 PFDI Dual-Fuel Ti-VCT)
REFERÊNCIA OE0261500360, 0261500361, FJ1431, JL3E-9F593-AB
VÁLVULA DE CONTROLOHigh-Response Multi-Hole Electromagnetic Nozzle
BICO INJETOR-
PRESSÃO DO RAIL250 bar
EMISSÕESTier 3 Bin 70 / Euro 6d-Temp / LEV III
GARANTIA12 Meses
01

Injetores Compatíveis

Ref. OEM
02

Aplicações por Veículo e Motor

VeículoMotorAnos
Ford F-1505.0L V8 Coyote Gen 3 PFDI2018-2023
Ford Mustang GT5.0L V8 Coyote Gen 3 PFDI2018-2023
Ford Mustang Mach 15.0L V8 Coyote Gen 3 PFDI2021-2023
03

Especificações Técnicas

EspecificaçãoValor
Tipo de sistemaFord Port Fuel & Direct Injection (PFDI) 250-bar System
Pressão de trabalhoEspec. Principal
Spray PatternLaser-Drilled Multi-Hole Symmetrical Spray Cone
INJECTOR HOLD-DOWN BOLT TORQUE10 N·m (89 in-lb) direct fuel rail securing bolts📐 Assistente de Binário e Ângulo →
FUEL LINE NUT TORQUE28 N·m (21 lb-ft) high-pressure crossover tube union nut
Combustion SealVirgin PTFE Teflon Sealing Ring (Pre-compressed)
Upper Rail O-RingFluorocarbon (FKM) High-Temp Bio-Ethanol Resistant
ManufacturerBosch (OEM for Ford Motor Company)
Bosch Production Number0261500360 / 0261500361
04

Dicas de instalação

  1. [
  2. {
  3. "step": 1,
  4. "title": "Dual-Fuel System Depressurization & Preparation",
  5. "instruction": "Depressurize both port fuel and direct injection systems by disabling the low-pressure fuel pump fuse and running engine until stall. Disconnect battery negative terminal."
  6. },
  7. {
  8. "step": 2,
  9. "title": "Intake Manifold & Upper Port Injection Rail Removal",
  10. "instruction": "Remove intake air ducting and throttle body connections. Disconnect low-pressure port injector wiring harness and unbolt upper intake manifold assembly to access the direct injection rail beneath."
  11. },
  12. {
  13. "step": 3,
  14. "title": "Direct Injection Rail & Steel Fuel Line Removal",
  15. "instruction": "Disconnect high-pressure direct fuel injector electrical plugs. Using a flare wrench, loosen the high-pressure crossover tube fittings. Remove fuel rail hold-down bolts (10 N·m) and withdraw rail with injectors."
  16. },
  17. {
  18. "step": 4,
  19. "title": "Cylinder Head Bore Cleaning & PTFE Seal Pre-Fitting",
  20. "instruction": "Clean injector combustion bores in the cylinder head using brass soft brushes and lint-free swabs. Ensure the pre-installed Teflon seal ring on the new Bosch injector is undamaged and free of engine oil/grease."
  21. },
  22. {
  23. "step": 5,
  24. "title": "Rail Alignment & Torque Specification Adherence",
  25. "instruction": "Lightly lubricate upper FKM O-rings with clean engine oil (keep lower Teflon dry). Press injectors into cylinder head bores, position direct fuel rail, and torque mounting bolts in two passes up to 10 N·m."
  26. },
  27. {
  28. "step": 6,
  29. "title": "High-Pressure Line Torquing & Engine Leak Inspection",
  30. "instruction": "Reinstall high-pressure fuel lines and torque flare nuts to 28 N·m. Reinstall intake manifold and port injection components. Cycle ignition 3 times to prime system and perform high-pressure fuel leak diagnostic check."
  31. }
  32. ]
05

Codigos de Falha (DTC) e Protocolos de Diagnostico

Codigos de falha diagnosticos (DTC) comuns acionados quando este injetor common rail apresenta desgaste, falhas de circuito ou desvio:

P0087Critical

Fuel Rail / System Pressure Too Low

Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.

P0201 - P0208High

Injector Circuit Malfunction / Open Circuit

Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.

P0300 / P0301+High

Cylinder Misfire & Balancing Deviation

Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.

P0088High

Fuel Rail / System Pressure Too High

Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.

Protocolos Técnicos de Diagnóstico & Manutenção

Procedimentos de oficina verificados, valores limite de teste e normas de serviço para este conjunto.

Protocolo de Diagnóstico de Oficina

Teste de Retorno de Injetores Common Rail: Valores e Limites

Procedimento de medição de retorno dinâmico de injetores diesel. Provetas graduadas, limites em ml/min, desgaste de válvula de controle e código P0087.

Ler protocolo técnico
IMA / QR Calibration

Codificação Injetor Bosch IMA: Posição e Guia 6-9 Dígitos

Ler protocolo técnico
SOP DE OFICINA DIESEL COMMON RAIL

Remoção de Injetor Preso e Descarbonização | Guia SOP

SOP profissional de oficina para remoção de injetor diesel preso, extração pneumática por vibração, dissolução de carvão e fresagem da sede sem danos.

Ler protocolo técnico
PROTOCOLO DE MONTAGEM E INSTALAÇÃO

Torques de Aperto Injetor Diesel & Ângulos de Graus

Tabela de torques de aperto para injetores diesel common rail e aperto angular TTY. Dados de oficina para Bosch, Detroit DD13, Cummins e VAG em N·m.

Ler protocolo técnico