Katalog / BOSCH / JL3Z-9F593-A
BOSCH

JL3Z-9F593-A

Zobrazit parametry
SolenoidFord Dual-Fuel PFDI (Port Fuel Injection + 250-bar Direct Injection)Euro 3706

BOSCH JL3Z-9F593-A Přímý Vstřikovač Ford F-150 Mustang 5.0L Coyote Gen 3

Referenční údaje vstřikovače Common Rail Bosch JL3Z-9F593-A · OEM 0261500360, 0261500361, FJ1431, JL3E-9F593-AB · Použití Ford 5.0L Coyote V8 (Gen 3 PFDI Dual-Fuel Ti-VCT)
OE ČÍSLO0261500360, 0261500361, FJ1431, JL3E-9F593-AB
ŘÍDICÍ VENTILHigh-Response Multi-Hole Electromagnetic Nozzle
TRYSKA-
TLAK V RAILU250 bar
EMISNÍ NORMATier 3 Bin 70 / Euro 6d-Temp / LEV III
ZÁRUKA12 Měsíců
01

Kompatibilní vstřikovače

OEM reference
02

Použití ve vozidlech a motorech

VozidloMotorRoky výroby
Ford F-1505.0L V8 Coyote Gen 3 PFDI2018-2023
Ford Mustang GT5.0L V8 Coyote Gen 3 PFDI2018-2023
Ford Mustang Mach 15.0L V8 Coyote Gen 3 PFDI2021-2023
03

Technické specifikace

ParametrHodnota
Typ systémuFord Port Fuel & Direct Injection (PFDI) 250-bar System
Provozní tlakKlíčový parametr
Spray PatternLaser-Drilled Multi-Hole Symmetrical Spray Cone
Utahovací moment šroubu upínky10 N·m (89 in-lb) direct fuel rail securing bolts📐 Průvodce momentem a úhlem utažení →
Utahovací moment vysokotlaké trubky28 N·m (21 lb-ft) high-pressure crossover tube union nut
Combustion SealVirgin PTFE Teflon Sealing Ring (Pre-compressed)
Upper Rail O-RingFluorocarbon (FKM) High-Temp Bio-Ethanol Resistant
ManufacturerBosch (OEM for Ford Motor Company)
Bosch Production Number0261500360 / 0261500361
04

Pokyny k montáži

  1. [
  2. {
  3. "step": 1,
  4. "title": "Dual-Fuel System Depressurization & Preparation",
  5. "instruction": "Depressurize both port fuel and direct injection systems by disabling the low-pressure fuel pump fuse and running engine until stall. Disconnect battery negative terminal."
  6. },
  7. {
  8. "step": 2,
  9. "title": "Intake Manifold & Upper Port Injection Rail Removal",
  10. "instruction": "Remove intake air ducting and throttle body connections. Disconnect low-pressure port injector wiring harness and unbolt upper intake manifold assembly to access the direct injection rail beneath."
  11. },
  12. {
  13. "step": 3,
  14. "title": "Direct Injection Rail & Steel Fuel Line Removal",
  15. "instruction": "Disconnect high-pressure direct fuel injector electrical plugs. Using a flare wrench, loosen the high-pressure crossover tube fittings. Remove fuel rail hold-down bolts (10 N·m) and withdraw rail with injectors."
  16. },
  17. {
  18. "step": 4,
  19. "title": "Cylinder Head Bore Cleaning & PTFE Seal Pre-Fitting",
  20. "instruction": "Clean injector combustion bores in the cylinder head using brass soft brushes and lint-free swabs. Ensure the pre-installed Teflon seal ring on the new Bosch injector is undamaged and free of engine oil/grease."
  21. },
  22. {
  23. "step": 5,
  24. "title": "Rail Alignment & Torque Specification Adherence",
  25. "instruction": "Lightly lubricate upper FKM O-rings with clean engine oil (keep lower Teflon dry). Press injectors into cylinder head bores, position direct fuel rail, and torque mounting bolts in two passes up to 10 N·m."
  26. },
  27. {
  28. "step": 6,
  29. "title": "High-Pressure Line Torquing & Engine Leak Inspection",
  30. "instruction": "Reinstall high-pressure fuel lines and torque flare nuts to 28 N·m. Reinstall intake manifold and port injection components. Cycle ignition 3 times to prime system and perform high-pressure fuel leak diagnostic check."
  31. }
  32. ]
05

Chybove kody (DTC) a diagnosticke protokoly

Bezne diagnosticke chybove kody (DTC), ktere se spousteji pri opotrebeni, zavade obvodu nebo odchylce kalibrace tohoto vstrikovace common rail:

P0087Critical

Fuel Rail / System Pressure Too Low

Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.

P0201 - P0208High

Injector Circuit Malfunction / Open Circuit

Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.

P0300 / P0301+High

Cylinder Misfire & Balancing Deviation

Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.

P0088High

Fuel Rail / System Pressure Too High

Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.

Technické diagnostické a servisní protokoly

Ověřené dílenské postupy, mezní hodnoty testů a servisní postupy pro tento díl.

Dílenský diagnostický protokol

Test Přepadu Vstřikovačů Common Rail: Mezní Hodnoty a Postup

Měření dynamického přepadu vstřikovačů Common Rail pomocí odměrných válců. Mezní hodnoty v ml/min při volnoběhu, opotřebení ventilu a diagnoza chyby P0087.

Číst technický protokol
IMA / QR Calibration

Kódování Vstřikovačů Bosch IMA: Umístění Kódu a 6-9 Znaků

Číst technický protokol
DÍLENSKÝ POSTUP PRO COMMON RAIL DIESEL

Demontáž zadřených vstřikovačů a čištění | FuelPartsDB

Dílenský postup demontáže zapečených vstřikovačů, vibračního vytahování, chemického rozpouštění karbonu a bezpečného zafrézování sedel v hlavě válců.

Číst technický protokol
MONTÁŽNÍ A INSTALAČNÍ PROTOKOL

Utahovací Momenty Vstřikovačů & Úhly Pootočení TTY

Utahovací momenty vstřikovačů common rail a úhly dotažení šroubů TTY. Dílenské tabulky pro Bosch, Detroit DD13, Cummins a VAG 2.0 TDI v Nm.

Číst technický protokol