DENSO
23209-0V010
Özellikleri Gör
SolenoidToyota Electronic Fuel Injection (EFI Multi-Port 47-psi System)Euro 255
DENSO 23209-0V010 Yakıt Enjektörü Toyota Camry RAV4 2.5L 2AR-FE
OEM REFERANSI
23209-36010, 23209-09140, 23280-36010, FJ1068KONTROL VALFİ
12-Hole Precision Multi-Orifice Micro-Droplet Atomizer PlateENJEKTÖR MEMESİ
-RAİL BASINCI
3.24 barEMİSYONTier 2 Bin 5 / Euro 5 / ULEV II
GARANTİ12 Ay
02
Uyumlu Araçlar ve Motorlar
| Araç | Motor | Model Yılları |
|---|---|---|
| Toyota Camry XV50 / RAV4 XA40 | Toyota 2.5L 2AR-FE & 2.7L 1AR-FE DOHC 16-Valve Dual VVT-i 4-Cylinder EFI | 2012-2018 |
| Toyota Highlander / Venza | Toyota 2.5L 2AR-FE & 2.7L 1AR-FE DOHC 16-Valve Dual VVT-i 4-Cylinder EFI | 2009-2019 |
| Toyota Scion tC (AGT20) 2.5L | Toyota 2.5L 2AR-FE & 2.7L 1AR-FE DOHC 16-Valve Dual VVT-i 4-Cylinder EFI | 2011-2018 |
| Lexus ES 250 (XV60) 2.5L | Toyota 2.5L 2AR-FE & 2.7L 1AR-FE DOHC 16-Valve Dual VVT-i 4-Cylinder EFI | 2011-2018 |
03
Teknik Özellikler
| Özellik | Değer |
|---|---|
| Sistem Tipi | Toyota Electronic Fuel Injection (EFI) Multi-Port Port Injection |
| Operating Fuel Pressure | 3.24 bar (47 psi / 324 kPa regulated) |
| Static Flow Rate | 280 cc/min @ 3.0 bar (26.6 lb/hr) |
| Electrical Resistance | 11.6 - 12.4 Ohms @ 20°C (High-Impedance Saturated Solenoid) |
| Spray Geometry | 12-Hole Precision Multi-Dispersal Micro-Atomization Director |
| Fuel Rail Fastener Torque | 9 N·m (80 in-lb) fuel rail mounting bolts |
| Seals Architecture | Upper Viton Fluorocarbon O-Ring & Lower Resilient Vibration Insulator |
| Manufacturer | Denso Corporation (Tier-1 OEM for Toyota Motor Corporation) |
| Denso Production Reference | 23209-0V010 / 23209-36010 |
| Çalışma BasıncıTemel Değer |
04
Montaj İpuçları
Püf Noktaları ve Uyarılar:
- Always replace lower manifold vibration insulators: Hardened lower rubber insulators allow unfiltered unmetered air into intake ports, causing persistent P0171 lean codes.
- Never use silicone sealant or grease: Lubricate O-rings strictly with fresh engine oil or spindle oil to prevent silicone contamination of oxygen sensors.
- Verify injector free rotation: After snapping injectors into the fuel rail, verify that each injector rotates smoothly by hand without binding.
- Prime fuel circuit prior to ignition: Turn ignition switch ON for 5 seconds twice without cranking to pressurize system and confirm zero fuel seepage.
05
Ariza Kodlari (DTC) ve Teshis Protokolleri
Bu common rail enjektorunde asinma, devre arizasi veya kalibrasyon kaymasi olustugunda tetiklenen yaygin ariza kodlari (DTC):
P0087Critical
Fuel Rail / System Pressure Too Low
Excessive internal backleak from worn control valve seats drops common rail pressure below target under engine load.
P0201 - P0208High
Injector Circuit Malfunction / Open Circuit
Solenoid coil resistance drift (0.2-0.5 Ω) or piezo stack degradation triggers driver stage shutdown on affected cylinders.
P0300 / P0301+High
Cylinder Misfire & Balancing Deviation
Carbon-clogged nozzle spray holes or missing IMA calibration causes uneven cylinder contribution. Recode ECM and verify washer seating.
P0088High
Fuel Rail / System Pressure Too High
Spill line backpressure or stuck metering valve prevents rail depressurization, creating overpressure risks under load.
ATÖLYE PROTOKOLLERİ
Teknik Arıza Teşhis ve Servis Protokolleri
Bu parça grubu için doğrulanmış atölye prosedürleri, test eşik değerleri ve servis talimatları.
Atölye Teşhis Protokolü
Teknik Kılavuzu OkuCommon Rail Enjektör Geri Dönüş Testi: Limitler ve Teşhis
COMMON RAIL DİZEL ATÖLYE SOP
Teknik Kılavuzu OkuSıkışmış Enjektör Sökme ve Karbon Temizleme | FuelPartsDB
MONTAJ VE KURULUM PROTOKOLÜ
Teknik Kılavuzu Oku